Turn the knob to adjust the opening size.

Slide the upper jaw to adjust the opening size. These clamps hold larger workpieces than other locking plier clamps of similar size.

A removable, heavy duty steel base plate provides a flat, durable clamping surface. Carry it where needed or mount the base plate to your workbench.

Press the lever down to lock these clamps, which fit in tight spaces and hold thin materials.

Mount these clamps to a bench top or other surface to keep workpieces in place.

Hold workpieces of slightly different thicknesses with one clamp. These clamps automatically adjust to compensate for imperfections or small inconsistencies on the material’s surface.

Reduce the chance of getting pinched when unclamping. These clamps have more space between the handle and the arm than other low-profile toggle clamps.

Hold workpieces of different thicknesses without adjustment.

Often used when assembling small parts, these small clamps have the holding strength of a full-size clamp.

The mounting base secures these clamps to a rail or bar.

Mount these clamps below a surface.

Weld these clamps to the side of an object or drill your own holes in the mounting plate and bolt into place.

Attach one of these nonmarring rubber or plastic tips to prevent a metal holding screw from damaging workpiece surfaces.

These clamps have mounting holes on the bottom.

Push or pull the plunger to hold your workpiece from the side.

Pull the handle backward to push the plunger forward. These clamps secure when the plunger is fully extended to hold your workpiece from the side.

Hold workpieces of different thicknesses without adjustment.

Moving parts are protected by a metal cover when the clamp is engaged to prevent dirt and dust from clogging the clamp.

Smaller than standard push toggle clamps, these are often used for electronics and small fixturing applications.

Drill a hole to mount these clamps through a surface and secure the mounting flange with screws. The plunger can be locked at any position along its travel.

Push the lever to lock the handle and prevent accidental opening.

Clamp up to three workpieces at 90° angles.

Clamp workpieces from the outside at a 90° angle, leaving the inside free for welding or fabrication.

Sized for small parts and tight spaces, these clamps have a pivoting pad at each end to hold workpieces at any angle up to 180°.

Hold magnetic workpieces in place with these clamps.

Two vise heads tilt and rotate 360°, locking in place to hold work at any angle.

For large workpieces, these vises open three times as wide as standard tilting-head vises. Tilt and lock the head to position work at an angle.

Use these vises for general purpose workholding.

For big jobs, these vises have a wider jaw opening, deeper throat depth, and larger footprint than standard vises.

Designed for outdoor use, these vises have a finish that resists corrosion.

Made of 304 stainless steel to stand up to washdown environments, such as food and beverage production, these are the most corrosion-resistant vises we offer.

Hold your smallest workpieces in these vises, which have a clamp-on base for quick installation and removal from a benchtop.

These V-shaped liners hold large round material.

Fold the pliable tabs over the jaws to install.

Replace worn flat and V jaws.

Turn the handle to move the jaw on these basic vises.

The base and three sides of the vise are ground flat, enabling mounting on its base, either side, or upright.

Use the adjustment dials to ensure your work is accurately positioned on X and Y axes.

Use these vises for reliable workholding on CNC machines.

Arrange the included pins in a series of holes to position a part at any angle and hold odd-shaped parts securely.

Hold workpieces steady with these vise jaws—they work with slot-mount workstops so you can quickly position, adjust, and change out your workpieces.

Quickly move parallels in and out of these jaws to raise your workpiece within the vise. Mount jaws to the vise, slide the mating parallels in place, and rest your workpiece on top.

The vise body and stationary jaw are one piece for high repeatability, even under heavy clamping loads. Ground flat on the base and three sides, these vises ensure accuracy whether mounted on the base, either side, or upright.

Designed to hold your part on 4- and 5-axis milling machines, these vises provide rigid clamping while exposing five full sides of the workpiece. This allows even complex parts to be completed in a single operation. You must cut a dovetail into your material before the vise can grip it.

The jaws move inward at the same time to consistently position your workpiece in the center of the vise.

Tilt the head on two axes and rotate the base to position your workpiece at almost any angle.

Jaw are serrated or grooved to firmly grip workpieces.

Plastic jaw inserts prevent damage to the workpiece.

Each end of the vise has a collet to hold a different tool—turn the collar to close the collets around them.

Clamp and unclamp with one hand by sliding the knurled ring forward to close the collet.

A rubber-covered body provides a comfortable grip. These vises have a rotating end cap on the handle that allows you to apply constant pressure while turning the body of the vise with your fingertips.

Notches on the jaws hold round material on its outside diameter.

Steel jaws secure round workpieces such as pipe, tubing, and conduit.

Keep clean rooms free of contaminants. These tripod-mounted vises have rubber-covered jaws that prevent metal-to-metal contact and a plastic-encased chain that seals in lubrication.

Lock the jaws in a vise-like grip around a workpiece and these pliers stay clamped in place to leave your hands free.

Hold larger workpieces than standard locking pliers. These tools lock in a vise-like grip around a workpiece and stay clamped in place.

Change out worn or broken springs in the handle of your locking pliers.

When there isn't clearance to use standard-grip locking pliers, the angled handle on these tools gives you access. Lock the jaws around a workpiece and these pliers stay clamped in place.

Clamp down on nonreinforced hose and tube to squeeze it shut, eliminating the need to drain the hose when working on pumps, heating and cooling systems, and fuel lines.

Attach your locking pliers to a slide hammer to pull stubborn objects.