Upgrade your traditional fluorescent washdown lights—these LEDs last longer and eliminate the need to replace bulbs.

Also known as troffers, these lights fit flush into most drop-ceiling grids. They’re fully sealed with an airtight gasket, so they’re rated IP65 for protection against low-pressure washdowns, humidity, and dust.

Suspend or mount with fasteners to the ceiling.

These lights produce a wide beam of uniform light to fill large, open areas with ceilings up to 18-ft. high.

Safely light up chemical processing plants, mining operations, and other large areas where combustible gases and dust are present. These lights have an explosion-proof housing that contains sparks and flames, so they won’t react to nearby hazards.

Don’t waste energy lighting unoccupied spaces—these lights turn on when they detect movement.

Upgrade your fluorescent recessed lighting to energy-efficient LEDs without removing fixtures and exposing insulation.

Link these lights together to create different shapes with a sleek look.

Customize these lights to label doors or areas of a building.

Create ambient and accent lighting with these sleek, modern lights that shine above, below, and around themselves.

To keep contaminants from entering your clean room, these lights seal against drop ceilings with an airtight gasket.

Mount these lights flush with ceilings in wet locations—all are sealed to keep out humidity and dripping, splashing, and falling liquids. Unlike recessed can lights, which require a separate housing, these fit directly into a cutout in your ceiling and are held in place by springs.

Just like traditional tubular lights that illuminate your machine with a bright white light, these lights can also be programmed to switch over to a red or green light for communicating machine status.

Mount these lights into a recessed opening on your machine—they sit flush against the surface for a streamlined appearance.

Update conventional fluorescent tubular lights with newer LED technology. These lights match the diameter of most older lights and fit existing brackets without the need to drill new mounting holes.

Illuminate inline flow sights to inspect the color, clarity, and flow of liquids in food and beverage, brewery, chemical, and pharmaceutical processing lines.

Pivot the head to cast a narrow beam of light to exactly where it's needed.

The articulating arm on these lights holds its position better than gooseneck-arm lights, especially around vibration.

Light up large, open rooms where you need a quick setup and takedown, such as a room under construction. Just hang these lights from a ceiling up to 30' high and they’re ready to go.

Light up damp areas—these lights seal out moisture and humidity. They’ll even work in areas with frequent washdowns. Rated NEMA 4X, they withstand spraying liquid, resist corrosion, and keep out dust.

Power these lights with the same battery as your other cordless tools. They run on a Milwaukee M18 battery to light up work where there’s no outlet.

From pipes to pallet racks to control panels—these lights clamp onto almost anything and swivel to direct light just where you need it.

Splashes and drips are no problem for these lights. They don’t need an outlet, so you can bring them wherever you need them.

Flood hazardous areas with light—these lights are intrinsically safe, meaning they can’t cause an explosion or fire. Rated NEC Class I, II, III, and Zone 0, they’re safe to use in areas with ignitable concentrations of flammable or combustible gases, dust, and fibers.

Safely light up large spaces where combustible gases and dust are normally present. Rated NEC Class I and II, these lights have a housing that contains any sparks or flames and seals out ignitable gases, vapors, and dust.

With a rounded, weighted base, these floodlights wobble—but don't fall over—when bumped.

Bring light to remote areas with the DeWalt rechargeable battery that's already in your toolkit.

Brighten remote areas, even if they’re damp or rainy. These floodlights are IP rated to keep out humidity and dripping, splashing, and falling liquids.

Our brightest plug-in floodlights, these lights illuminate large worksites—about the size of a hockey rink.

As bright as stadium lights, these floodlights are the most powerful in our offering—they’ll brighten jobsites half the size of a football field. They run on a diesel generator you can use to power other lights and tools in the field.

Raise, lower, and tilt these lights to brighten your work in wet spaces.

Hardwire these lights to a power source.

Also known as wall packs, these lights mount to exterior walls and ceilings.

These lights are UL listed for use in hazardous locations where flammable/combustible gases, vapors, and liquids may be present.

Shine light into hard-to-reach spaces—these flashlights have a flexible arm to see around tight corners and in crevices. They’re rated for use in environments where flammable gases, vapors, and liquids are present.

Tilt the head on these flashlights to point light where you need it in explosion-prone areas. Rated NEC Classes I and II, they’re safe to use where there are ignitable concentrations of flammable or combustible gases, vapors, liquids, and dust.

When the power goes out, these flashlights automatically light up. The head tilts so you can aim light wherever you need it.

Shine light into hard-to-reach spaces with these flexible-arm flashlights.

Clip these little flashlights to a baseball cap or a surface to light up your work.

At full power, these flashlights shine as bright as a stadium light. They’re the brightest in our offering.

Light up objects more than a quarter of a mile away. These flashlights are also known as searchlights.

All of these flashlights stand up to wet environments.

Light up work without risking an explosion. NEC rated, these headlamps are safe to use in areas with ignitable concentrations of flammable or combustible gases, vapors, and liquids.

Drop these headlamps in water and they’ll still work—they’re IP rated to withstand submersion for at least 30 minutes.

Safe to use in areas with ignitable concentrations of flammable or combustible gases, vapors, liquids, and dust, these lights are rated NEC Class I, II, and III.

Brighten loading docks and trailers—these lights swing out from the wall and tilt to direct light where it’s needed.

Light the path toward exits where combustible gases and dust are constantly present—the enclosure on these lights contains sparks and flashes to prevent a reaction with nearby hazards. They’re often found in extreme environments, such as refineries and chemical plants.

These lights are rated IP69K to withstand high-pressure washdowns, such as those in food and beverage applications.

You can use these lights outdoors and they will still be visible. Rated IP67 for harsh environments.

These lights have lenses that snap in and out, so you can easily swap colors or change their position in the stack.

Highlight small, specific areas with intensely bright light to help your machine vision camera home in on the details of your product.

Ranging in size from a domino to a small TV remote control, these lights shine bright, even light from tight spots on your production line. Use them to help your machine vision camera capture a detailed image for inspection.