Extend the service life of air-powered tools and equipment by removing particles and water droplets from compressed air.

Extend the service life of air-powered tools and equipment by removing particles and water droplets from compressed air.

Extend the service life of air-powered tools and equipment by removing particles and water droplets from compressed air.

Extend the service life of air-powered tools and equipment by removing particles and water droplets from compressed air.

An automatic drain discharges up to 300 gallons per hour to handle compressed air with high moisture content.

Get two stages of filtration—the first stage removes most particles and water droplets; the second captures any remaining particles and water droplets down to 5 microns.

Assembled, inspected, and packaged in a clean environment, these filters come sealed in anti-static double bags.

Protect small air-powered tools, such as impact wrenches, ratchet wrenches, grinders, and screwdrivers.

Two-stage filtration is like getting two filters in one—the first stage removes large particles, while the second removes fine particles.

No need to buy and service two filters—these filters have a single element that removes both large and fine particles.

Also known as coalescing filters, these filters remove compressor oil to extend the service life of air-powered tools and equipment.

Also known as coalescing filters, these filters remove compressor oil to extend the service life of air-powered tools and equipment.

Generate clean air for instrumentation and applications with critical air requirements.

Remove bacteria, viruses, moisture, and other particles from compressed air and gases used in food, pharmaceutical, biotech, and electronics applications.

Prevent equipment damage and wear caused by moisture in your compressed air supply. The first step in water removal, use one of these separators to remove the large amount of water created as compressed air cools.

When water is condensed out of a compressed air system, it contains oil from the compressor that makes disposal difficult. These separators use two-stage filtration to reduce oil content to below 20 parts per million.

A filter and regulator joined top-to-bottom, these filter/regulators fit in the same space as a filter alone.

A filter and regulator joined top-to-bottom, these filter/regulators fit in the same space as a filter alone.

A filter and regulator joined top-to-bottom, these filter/regulators fit in the same space as a filter alone.

A filter and regulator joined top-to-bottom, these filter/regulators fit in the same space as a filter alone.

A clear polyurethane bowl makes these filter/regulators chemical resistant for use with synthetic compressor oils and cleaning fluids and allows you to see inside to monitor contents.

A stainless steel housing and bowl allow these filter/regulators to withstand corrosive environments in the semiconductor, marine, chemical, instrumentation, and paper industries.

No need for thread adapters—these filter/regulators have an NPT inlet and a BSPP outlet.

A Wilkerson filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.

An ARO filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.

A Festo filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.

An ASCO Numatics filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.

Three components are combined in the same space as a filter alone. These units provide clean, lubricated compressed air at your required pressure.

No need for thread adapters—these filter/regulator/lubricators have an NPT inlet and a BSPP outlet.

These dryer/filters have a clay desiccant that removes moisture, oil, and particles, so there’s no need to install a separate filter and dryer. Once aftercoolers and separators have removed the bulk of the water, they remove any remaining moisture in your air line.

With a clear polycarbonate bowl that’s visible from all angles and silica gel desiccant that changes from blue to pink, it’s easy to see when it’s time to change the cartridge on these dryer/filters and dryer/filter/regulators.

For use with Norgren modular compressed air systems, once aftercoolers and separators have removed the bulk of the water, use one of these desiccant-filled dryers to remove any remaining moisture in your air line.

Install these dryers just before air-powered tools as final protection from water and particles and throw them away when you’re done.

These all-in-one dryer/filters eliminate the need for individual dryers, separators, and filters. They cool air through refrigeration to condense water vapor for removal.