Light diffuses evenly from the sides and bottom to produce ambient lighting. These fixtures are ideal for offices, storage rooms, and other indoor spaces.

Also known as strip or channel lights, the ends of these fixtures are designed to be wired together to create long rows of lights.

Upgrade your fluorescent recessed lighting to energy-efficient LEDs without removing fixtures and exposing insulation.

Maximize the light that reaches your shelving. Often used in storage rooms and warehouse rack rows, these lights have reflectors that direct all light downwards from ceilings up to 24 ft. high.

Light up spaces that have no electrical connection or are difficult to wire, such as sheds and closets.

Brighten entryways and small spaces.

With more surface area than round bay lights, these fixtures produce softer light with less glare. Use them to replace old fluorescent lights and illuminate large, open areas with high ceilings.

Rated for over a decade of use well above 100° F, these linear bay lights long outlast standard facility lights in high heat.

Often used in stairwells and hallways, these lights save energy by only turning on when they sense movement.

Illuminate steps to reduce the risk of tripping or falling, especially at night or in poorly lit areas.

Illuminate chemical plants, refineries, and other facilities where flammable and combustible gases may be present in the event of a leak or ventilation failure. These lights are rated for use in NEC Class 1, Division 2 hazardous locations.

Built for hot, hazardous areas such as steel mills and refineries, these lights work in temperatures up to 212° F. Rated NEC Classes I and II, they’re safe to use where there are ignitable concentrations of flammable or combustible gases, vapors, liquids, and dust.

Contain explosions, sparks, and flashes—the enclosure on these ceiling lights makes them safe to use in NEC Class I and II, Division 1 hazardous locations.

Mount these lights in recessed spaces so the lens is flush with the ceiling or wall. NEC Classes I and II, they’re safe to use in paint spray booths, blast booths, and other areas with ignitable concentrations of flammable or combustible gases, vapors, liquids, and dust.

Also known as troffers, these lights fit flush into most drop-ceiling grids. They’re fully sealed with an airtight gasket, so they’re rated IP65 for protection against low-pressure washdowns, humidity, and dust.

Illuminate areas that need frequent cleaning, such as food processing lines, with long rows of lights. Rated IP65, these lights have a sealed lens and liquid-tight end caps that protect them from low-pressure washdowns and dust.

Tough enough for offshore rigs and seafaring vessels—yet less than half the height of typical jelly jar lights. Built with a thick aluminum housing and a tough polycarbonate lens, these lights withstand hard impact without a guard.

Also known as sconces, these lights are a stylish choice for ambient and accent lighting in hallways and entryways. They’re UL or ETL listed for wet locations, so you can install them outdoors—rain and humidity won’t be a problem.

Prevent contaminants from entering your ISO Class 3 clean room—these lights have an airtight seal.

Mount these lights into a recessed opening on your machine—they sit flush against the surface for a streamlined appearance.

Illuminate machines or monitor processes in environments that reach up to 210° F. These lights have a thick housing that acts as a heat sink to protect the LEDs and driver from overheating.

These classic-style machine lights have a reflector to distribute light more evenly than strip machine lights.

Just like traditional tubular lights that illuminate your machine with a bright white light, these lights can also be programmed to switch over to a red or green light for communicating machine status.

These thin, flexible lights wrap around equipment, hide under cabinets, and squeeze into tight spaces—all you need is an outlet. Just peel and stick to attach them to any smooth surface.

Brighten countertops that your ceiling lights can’t reach. These lights are low-profile, so they won’t take up valuable workspace below your cabinets.

Also known as wall packs, these lights mount to exterior walls and ceilings.

Powered by the sun, these security lights function in areas that don’t have access to electricity. They’re often used to shine light on parking lots, landscaping, signs, entryways, and other outdoor spaces.

Hardwire these lights to a power source.

These lights automatically turn on when movement is detected and off when an area is unoccupied.

Light up offshore rigs, coal mines, and other outdoor areas where gas, vapor, or dust could ignite. These lights have an enclosure that contains sparks and explosions, so they won’t react with nearby hazards.

Guide pedestrians and drivers at night with lighting that defines paths and driveways. These lights produce ambient illumination without the glare of overhead lights.

Heads adjust to any angle so you can direct light where needed.

These lights cast a narrower beam than other gooseneck-arm machine lights. Reposition them faster and more easily than articulating-arm lights.

Gooseneck arms can be repositioned faster and more easily than articulating arms.

Brighten loading docks and trailers—these lights swing out from the wall and tilt to direct light where it’s needed.

Safe to use in areas with ignitable concentrations of flammable or combustible gases, vapors, liquids, and dust, these lights are rated NEC Class I, II, and III.

Light the path toward exits where combustible gases and dust are constantly present—the enclosure on these lights contains sparks and flashes to prevent a reaction with nearby hazards. They’re often found in extreme environments, such as refineries and chemical plants.

Illuminate outdoor exit paths and emergency assembly areas during power outages.

Install these lights in aircraft hangars, gas plants, and other facilities where flammable and combustible gases or dust may be present, such as leaks or ventilation failures. Rated NEC Class I, Division 2, they seal out gases but aren't built to contain explosions.

No bigger than a roll of tape, these lights fit inside equipment to provide visibility during tool changeovers and maintenance.