A slit along the length makes this sleeving easy to install over wire, cable, and hose without disconnecting them. The corrugated construction gives it impact and abrasion resistance similar to conduit, with more flexibility.

This sleeving reflects heat away from contents and withstands temperatures up to 300°F. A slit along the length makes it easy to install over wire, cable, and hose without disconnecting them. The corrugated construction gives it impact and abrasion resistance similar to conduit, with more flexibility.

The corrugated construction gives this sleeving impact and abrasion resistance similar to conduit, but with more flexibility.

The two halves of this sleeving nest into each other, fully enclosing contents. It has interlocking ridges that overlap to keep out dust and dirt. The corrugated construction gives it the impact and abrasion resistance of conduit, with more flexibility.

Tight braiding makes this sleeving resistant to fraying when cut with scissors. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.

Rated UL 2024 and NFPA 262, this sleeving is approved for use in plenum spaces such as duct work and above a drop ceiling. It self-extinguishes and emits minimal amounts of smoke and gas during combustion. Stretch to fit over items for easy installation; it tightens around its contents for a secure fit.

Braided from thick plastic strands, this sleeving has excellent abrasion resistance. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.

Protect cable, hose, and pipe in high temperature environments—this sleeving withstands temperatures over 450° F. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.

This sleeving withstands temperatures up to 390°F and is often used to insulate connections in transformers and relays. It prevents electricity and heat from dissipating from wire and cable.

A specially formulated silicone rubber coating allows this sleeving to stretch over items during installation; it then tightens around its contents for a secure fit.

Made from thicker and denser fiberglass than standard spark-resistant sleeving, this sleeving is more abrasion resistant and provides better insulation. The silicone rubber coating protects against sparks and molten metal splash.

Unlike fiberglass and silica, this sleeving won't irritate skin, so it's easier to handle. It has a temperature rating of 1100° F or higher.

With a temperature rating of 1800°F or higher, this sleeving can withstand hotter temperatures than fiberglass and most ceramic.

Made of Nomex fabric, this sleeving has excellent tear resistance and better abrasion resistance than nylon sleeving.

Wrap this sleeving around cable, cords and wires to protect them and to form bundles.

Made of PTFE, this sleeving has excellent resistance to chemicals and acids. A reusable alternative to tape and cable ties, it allows you to route wire and cable between the spirals.

A strip of hook-and-loop creates a strong seal along the entire length of this sleeving, yet it can be opened at any point to access contents. Use it to wrap around wire, cable, or hose without disconnecting them.

Snaps keep this sleeving securely closed, yet permit quick access to contents and allow you to route wires in between the snaps. Use it to easily wrap around wire, cable, and hose without disconnecting them.

Organize and protect the cables on your Universal Robots arm without hindering its movement.

Made of aluminum with a fiberglass liner, this sleeving reflects heat away from contents and withstands temperatures up to 390°F. A slit along the entire length makes it easy to install around wire, cable, and hose without disconnecting them.

Coated with PVC, this polyester sleeving resists chemicals and solvents. It has a slit along the entire length so it easily wraps around wire, cable, and hose without disconnecting them.

Silicone rubber coats this fiberglass sleeving to shed sparks and molten metal splash. It has a slit along the entire length so it easily wraps around wire, cable, and hose without disconnecting them.

A mica and silicone rubber blend allows this sleeving to withstand temperatures up to 2100° F. It can be quickly applied to hose or cable like tape, so it's a good option for emergency patches.

These cable ramps handle heavy pedestrian and equipment traffic.

Curve these ramps to route cable around bends and corners in indoor areas with heavy pedestrian and equipment traffic.

Multiple channels let you separate different types of cable and cords.

These cable ramps are strong enough to withstand equipment traffic.

Often used as an alternative to cable ties, wire duct guides and organizes short runs of electrical wiring in enclosures, control panels, and machines.

Faster to install than standard slotted wire duct, attach this to flat, clean surfaces.

Built with snap-in tabs and a spring extension, these cord grips install into panel holes more quickly than standard grips and better prevent damage from sharp bends.

Made of nylon, these grips resist chemicals.

These cord grips are lightweight yet durable.

Secure and seal electrical cords entering knockouts at a 45° angle.

Stronger than aluminum cord grips, these grips are zinc plated for corrosion resistance.

Able to stand up to rust better than steel grips, these 300 series stainless steel grips secure electrical cables in corrosive environments.

Extend your cord’s life while stopping it from coming loose in places that are sanitized with water or steam as hot as 300° F, such as food plants and clean rooms.

Vent air from your enclosure to equalize pressure and stop condensation from forming inside while securing cords in wet environments. These polyamide grips are lightweight and resist rusting.

Wrap the split gland of these grips around ethernet cables with an RJ45 connector or other already installed cables for a water-resistant seal with your enclosure.

Secure cords installed through enclosures and panels in wet environments while protecting them against sharp bends. With a flared end that keeps cords from bending without limiting too much motion, these grips extend cord life.

These grips are made of nylon, which resists most chemicals. The nylon mesh extension provides a secure hold when the cable is pulled or in motion.

Made of PBT, these grips resist soaking up water in washdown and other wet environments while securing cords with an extra-strong hold.

Keep your cord at a gentle angle without sacrificing a tight hold, even in tough, wet environments.

Create a tight grip on cords in wet environments while reducing stress from bending—the 90° angle of these cord grips routes cords to fit tight spaces in enclosures and panels.

Lighter in weight than steel and brass grips, these aluminum grips are strong enough to secure cords in demanding wet environments.

Keep cords from coming loose and seal water out of enclosures in extremely cold labs and storage areas. Thanks to their plastic bushing and rubber O-ring, these grips withstand temperatures as low as -75° F.

These grips have an extension that provides extra support for moving cable and prevents kinking for longer cable life.

Made of nylon, these grips resist chemicals. Install them in panels and enclosures—they have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the enclosure.

Made of nylon, these grips resist chemicals. Install them in panels and enclosures—they have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the enclosure.

Secure cords in wet and industrial environments with little room—these grips curve 45° to relieve bending stress.

These cord grips are lightweight yet durable. They have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the connection.

Stronger than aluminum cord grips, these grips are zinc plated for corrosion resistance. They have a steel locknut and metal-reinforced O-ring that prevents liquid from entering the connection.

Stainless steel construction offers the most corrosion-resistance of any of our multi-diameter wet-location cord grips.

These 90° elbows meet Class III, Divisions 1 and 2 standards for use in hazardous locations.

The cable-entry side has heat-shrinkable polyolefin with an adhesive lining. These are also known as cable-entry seals.

The face of these grips is flush with the cable-entry point for a seamless appearance. They have a thin, flexible seal that covers the holes until you push a cord through.

Peel away layers of rubber inserts to fit around cord grips, even when you don't know the exact diameter.

These grips have a thin, flexible seal that covers the holes until you push cords through.

Attach a cord grip to cable without removing connectors and rewiring. These cord grips have a two-piece design to fit around cables with connectors.