1/10 hp Pumps | McMaster-Carr

Clear All

	Voltage Voltage

115V AC

120V AC

240V AC

	For Use With For Use With

Deionized Water

Ethylene Glycol

Water

	Intake Pipe Size Intake Pipe Size

	Power Source Power Source

Electric

	Discharge Pipe Size Discharge Pipe Size

1/2

	Electrical Connection Type Electrical Connection Type

Hardwire

Plug

	Power Power	Show

1/10 hp

	Power Power	Hide

	Maximum Flow Rate Maximum Flow Rate

	Flow Rate @ 10 ft. of Head Flow Rate @ 10 ft. of Head

11 gpm

12 gpm

	Pump Type Pump Type

Centrifugal

Submersible

	Maximum Feet of Head Maximum Feet of Head

Less than 100 ft.

	Duty Cycle Duty Cycle

Continuous

	Current Current

0.7A

1.2A

1.7A

	Maximum Temperature Maximum Temperature

Less than 100° F

150° to 199° F

	Frequency Frequency

60 Hz

	Maximum Pressure Maximum Pressure

10 psi

	Housing Material Housing Material

ABS Plastic

Polypropylene Plastic

PPS Plastic

	Phase Phase

Single

	Pump Style Pump Style

Circulating

	Intake Connection Type Intake Connection Type

Pipe

Inlet

	Discharge Thread Type Discharge Thread Type

NPT

	Motor Enclosure Type Motor Enclosure Type

Totally Enclosed Fan Cooled
(TEFC)

Open

	RoHS (Restriction of Hazardous Substances) RoHS (Restriction of Hazardous Substances)

RoHS Compliant

Forward

How can we improve?

4 Products

How to Prime Your Pump

How to Determine Feet of Head

About Process Pumps

About Sump, Water-Removal, Condensate, and Submersible Pumps

Low-Maintenance Plastic Circulation Pumps for Water and Coolants

Eliminate seal wear and leakage with pumps that use magnets to turn the impeller. They’re often used with electroplating and photographic solutions. Pumps are gravity fed and require an elevated liquid source to fully fill the pump before turning on. Do not run dry or use with solids.

Note: If flow control is needed, place valves or reducers on the discharge side; never restrict the inlet of a pump with a valve or reducer.

Pumps With Pipe Connections

With Pipe Connections

	Flow Rate, gpm								Intake			Discharge			Overall
Max. Flow Rate, gpm	@ 10 ft. of Head	@ 20 ft. of Head	Max. ft. of Head	Max. Pressure, psi	Max. Viscosity, cP	Temp. Range, °F	hp	Current, A	Pipe Size	Gender	Thread Type	Pipe Size	Gender	Thread Type	Lg.	Wd.	Ht.		Each
115V AC, Single Phase—With Thermal Overload Protection
Plug
14	11	4	24	10	20	35° to 150°	1/10 hp	1.7	1	Female	NPT	1/2	Male	NPT	9 5/8"	5 1/2"	4 7/8"	0000000	0000000

Harsh-Environment Low-Maintenance Plastic Circulation Pumps for Water and Coolants

These pumps have a totally enclosed fan-cooled (TEFC) motor for use in dusty, dirty, and damp environments. The impeller is turned with magnets to eliminate seal wear and leakage for a long service life. Pumps are often used with electroplating and photographic solutions. They are gravity fed and require an elevated liquid source to fully fill the pump before turning on. Do not run dry or use with solids.

Note: If flow control is needed, place valves or reducers on the discharge side; never restrict the inlet of a pump with a valve or reducer.

	Flow Rate, gpm							Intake (NPT)		Discharge (NPT)		Overall
Max. Flow Rate, gpm	@ 10 ft. of Head	@ 20 ft. of Head	Max. ft. of Head	Max. Pressure, psi	Max. Viscosity, cP	hp	Current, A	Pipe Size	Gender	Pipe Size	Gender	Lg.	Wd.	Ht.		Each
120V AC, Single Phase—With Thermal Overload Protection
Plug
14	12	4	24.3	10	20	1/10	1.7	1	Female	1/2	Male	10 7/8"	5 1/2"	5"	00000000	0000000
240V AC, Single Phase—With Thermal Overload Protection
Hardwire
14	12	4	24.3	10	20	1/10	0.7	1	Female	1/2	Male	10 5/8"	5 1/2"	5"	0000000	000000

Submersible Pumps for Water

Style B

		Max. Flow Rate, gpm								Discharge				Overall
	Electrical Connection Type	@ 1 Ft. of Head	@ 5 Ft. of Head	@ 10 Ft. of Head	Max. Ft. of Head, ft.	Temp. Range, °F	Horsepower	Current, A	Intake Inlet Connection Type	Pipe Size	Thread Type	Gender	Cord Length, ft.	Ht.	Wd.	Dp.		Each
115V AC, Single Phase—Without Thermal Overload Protection
B	Plug	9.2	7	3.5	13	35° to 85°	1/10 hp	1.2	Screened	1/2	NPT	Male	16	3"	4"	5"	0000000	0000000