These pumps have a totally enclosed fan-cooled (TEFC) motor for use in dusty, dirty, and damp environments. The impeller is turned with magnets to eliminate seal wear and leakage for a long service life.

These pumps can be used to move water and lubricating oil in boiler feed systems, cooling towers, and heat exchangers.

The motor is totally enclosed fan-cooled (TEFC) for use in dusty, dirty, and damp environments. Use these pumps to move water and lubricating oil in boiler feed systems, cooling towers, and heat exchangers

Also known as booster pumps, these have a multistage impeller that propels water about two times higher and farther than standard circulation pumps. Use them in applications such as water delivery, irrigation, and pressure washing.

Instead of a fan-cooled motor, these pumps have an integrated motor that's cooled by the liquid being pumped for virtually silent operation and a long service life. Also known as canned motor pumps, they're commonly used in chiller systems and aquariums.

A high-horsepower motor handles four times the flow and twice the pressure of other inline circulation pumps. Install these pumps directly in your pipeline for applications such as hot-water circulation and hydronic heating and cooling.

Eliminate seal wear and leakage—these pumps have magnets that turn the impeller for a long service life. Install them directly in your pipeline for applications such as hot-water circulation and hydronic heating and cooling.

Use these pumps in pipelines with limited clearance. Install directly in your pipeline for applications such as hot-water circulation and hydronic heating and cooling.

Drain underground tanks and process wastewater with pumps that can be installed up to 20 ft. above your liquid source.

A sealless construction means these pumps have few moving parts that can fail and shorten service life. The intake can be completely submerged in liquid.

Use when space is limited—these pumps connect to a pipe coming from your tank so you can place the pump in another location.

Self-priming up to 6 ft., these pumps have a stainless steel housing sealed with PTFE to resist chemicals such as ammonia and detergents as well as harsh solvents including methyl ethyl ketone (MEK).

Rated for continuous use, these pumps are often used to move caustics such as antifreeze and salt water. Mount them in any position, even upside down. Also known as diaphragm pumps, they are typically used for low-flow spraying, draining, and washdown applications.

Also known as gear pumps, these produce a smooth flow of liquid for applications such as cooling engines, powering hydraulic equipment, and extracting liquid from holding tanks.

These pumps quickly empty drum contents by moving 48 gallons of liquid per minute. Their electric motors are UL listed for use in environments with flammable gases and combustible dust.

Alter the flow rate for versatile dispensing.

Including nozzles and connectors, these pumps come with everything you need to start pumping.

These pumps are rated for fuel such as gasoline, kerosene, and diesel fuel.

Also known as bilge pumps, these remove fresh and salt water from spots where other pumps don’t fit.

Clean up water in flooded areas without a sump pit. Pumps activate when plugged in. You can add a plug-in switch to control when the pump activates.

Use these pumps to remove water with small solids up to 1/4" in diameter. They include a 25-ft. hose with cam-and-groove fittings for quick, secure connections.

Move higher volumes of water than with other high-flow water-removal pumps. These pumps activate when plugged in. You can add a plug-in switch to control when the pump activates.

These pumps provide about 25% more flow than standard float-switch activated pumps for sewage water. Equipped with a large intake and rugged impeller, they transfer raw sewage water with solids up to 2” in diameter. The float switch is wired to the pump.

The float switch has a separate cord that can unplug, so you can replace the switch without replacing the whole pump.

Equipped with a large intake and a rugged impeller, these pumps transfer raw sewage water with solids up to 2” in diameter. The float switch is wired to the pump.

These pumps have a heavy duty motor with sealed bearings that generates a flow rate similar to our other sump pumps for sewage water while using fewer amps. Use them to transfer raw sewage water with solids up to 2” in diameter. The float switch is wired to the pump.

Pumps have a cast iron housing that stands up to demanding environments. The float switch is wired to the pump. Use with debris-free water.

These pumps activate when plugged in. You can add a plug-in switch to control when the pump activates. Use with debris-free water.

These pumps have an explosion-proof motor that is rated for use where hazardous material is present. Since the motor is totally enclosed fan cooled (TEFC) and never comes into contact with the water, the pump can be used with hot water up to 300° F.

Convenient for applications where a sump pit is impractical, these pumps include a basin. Use with debris-free water.

Move higher volumes of water with solids than other sump pumps. The float switch has a separate cord that can unplug, so you can replace the switch without replacing the whole pump. Also known as effluent pumps, they accommodate solids up to 3/4” in diameter. They are often used with liquid waste that has passed through a septic tank, so most solids are removed.

These pumps activate when plugged in. You can add a plug-in switch to control when the pump activates. Also known as effluent pumps, these accommodate solids up to 3/4" in diameter. They're often used with liquid waste that has passed through a septic tank, so most solids are removed

Use these pumps at temperatures up to 200° F. Also known as effluent pumps, they accommodate solids up to 3/4” in diameter. They’re often used with liquid waste that has passed through a septic tank, so most solids are removed. The float switch is adjustable and wired to the discharge pipe.

If the primary float fails, the backup float kicks in and an alarm sounds to indicate float malfunction.

Hang these switches in a sump pit to detect rising water levels.

Rated for liquids with a viscosity up to 10,000 centipoise, these pumps can be used with very thick chemicals such as electropolishing solutions.

Automatically control output from a distance using 4‐20 mA or external-pulse signals. These pumps meter a consistent amount of liquid within ±2% of the maximum flow.

For high-volume chemical sampling and draining, these pumps have a powerful motor that enables them to move 2,448 gallons of liquid per day.

An adjustment dial with a locking lever allows for easy flow control. Also known as diaphragm metering pumps, these can be used with pressures up to four times higher than standard pumps for chemicals.

An adjustment screw lets you increase or decrease flow rate without the hassle of changing tubing. Often used in boiler feed systems and water treatment, these pumps are compatible with chemicals such as cleaning fluids and acid-washing solutions.

These pumps can be submerged or connected remotely to a pipe in your line. Use them to circulate water in small tanks, cooling baths, fountains, and other low-flow applications.

The durable epoxy-coated aluminum housing handles hard knocks in rough waters. Submerge these pumps to circulate water in small tanks, cooling baths, fountains, and other low-flow applications.

These pumps can be submerged or connected remotely to a pipe in your line. Magnets turn the impeller so there's no shaft seal to wear out. Use to circulate water in small tanks, cooling baths, fountains, and other low-flow applications.

These pumps circulate solvent-based parts-washing solutions.

Fully submersible, these pumps are designed for installation inside your condensate collection tank or drain pan. Use them to collect and remove condensate from air conditioners, refrigerators, dehumidifiers, and other equipment.

The stainless steel tank has excellent corrosion resistance. Designed for use in low-pressure steam systems, these pumps capture steam in the attached tank and return hot condensate to your boiler or feed unit.

Use these pumps in low-pressure steam systems to capture hot condensate and return it to your boiler or feed unit.

To handle high condensate volume, the workload is distributed between two pumps for a longer service life than standard high-flow steam condensate pumps. These pumps move a higher volume of condensate than standard steam condensate pumps. Use them in low-pressure steam systems to capture hot condensate and return it to your boiler or feed unit.

Generate a vacuum on demand with these pumps that come mounted on a 10-gal. ASME code vacuum tank for quick startup. They're often used in vacuum-forming applications, such as product packaging.

Achieve powerful vacuum and continuous flow for applications such as vacuum drying, solvent evaporation, and distillation.

Pressurize air for sprinkler systems. These compressors turn on when the tank falls to the activation pressure and they turn off when the tank reaches the maximum pressure.

Choose from pumps that dispense with a set interval. Turn the dial to adjust the flow from 0.1 oz. to 0.2 oz. per cycle.

With a maximum flow of 0.005 oz. per cycle, these pumps deliver small, precise amounts of oil. Turn the dial to set the cycle interval.

These dispensers have a reservoir for recirculating coolant.