Knock out pins and rivets that have already been loosened. These tools are also known as pin punches.

Impact-resistant steel makes these punches stronger and more durable than standard pin-removal punches.

Minimize damage to your work surfaces with these brass punches, which are softer than steel punches.

Loosen pins and rivets before removal.

A hammer and punch in one, this tool knocks out pins, rivets, and bolts.

Impact-resistant steel makes these punches stronger and more durable than standard pin-removal punches.

The punches in these sets have a knurled handle, which offers a more secure grip than standard punches. Use them to knock out pins and rivets that have already been loosened.

Line up holes by driving these pins through existing rivet, pin, and bolt holes in multiple pieces of metal. Alternatively known as lineup taper punches.

These brass tools reduce marring on metal surfaces because they're softer than steel punches.

When one side wears out, use the other one.

Punch a hole in your material to prepare for the installation of fabric grommets. Strike these tools with a mallet.

These punches set grommets that have a standard washer, tooth lock washer, or an extended-neck washer.

Contains pin-loosening, pin-removal, and center-marking punches as well as chisels.

Sets include three punches in various point diameters to set nails flush or drive them out of view without damaging wood surfaces.

Strengthened edges cut holes up to 4" dia. in fabric, leather, rubber, and soft metal. Also known as arch punches.

Make oblong holes in fabric, leather, and rubber. Also known as arch punches.

Sets include common ID and OD sizes to create gaskets and washers in two strikes.

For accurate punching of inner and outer holes, these sets come with pilots that attach to the outer hole punch.

Screw one of the interchangeable heads into the included handle to create holes up to 3/16" dia. in tight spaces.

Create holes for installing heavy duty industrial connectors. When the die and punch are pressed together, four centering mandrels in the die mark where to drill holes for the connector's assembly.

Cut DIN-size holes in steel up to 7/64" thick using a driver ram and hydraulic pump.

The driver supplies eight tons of force to the hole punches in this set to make straight punches.

Create larger holes and make repeated punches with these drivers that supply 11 tons of force to the included hole punches.

Punch conduit up to size 1 1/4.

Forged steel makes the body of this punch more durable than the Economy Plier-Action Multiple-Size Hole Punch.

Squeeze the spring-return handle to punch round holes of a single size.

These punches are half the size of standard portable lever-operated punches. They come with punches and dies in varying sizes.

Deliver nearly three times the punching force of a standard portable lever-operated punch by holding one handle and turning the other 360°.

A throat depth more than double those of standard bench-mount lever-operated punches allows this tool to reach further past the edge of material.

Our most powerful lever-operated punch, the rotary-action socket turns to deliver two to three times the punching force of other bench-mount lever-operated punches.

Includes all six sizes of our individually sold hand-driven hole punches plus a tool to remove punched out material.

These high-speed steel saws cuts through aluminum, brass, bronze, and steel.

Make clean, fast cuts in thin metal and plastic when you use one of these saws with an impact driver. The body widens at the top to prevent the saw from pushing through your workpiece.

An extra-thick steel body with carbide teeth can cut through stainless steel structural framing and electrical enclosures.

Attach these saws to your portable drill to cut a range of large diameter hole sizes in sheet metal.

These standard saws have high-speed steel teeth.

The carbide teeth on these saws last up to twice as long as high-speed steel teeth.

The carbide-tipped teeth on these saws last up to twice as long as high-speed steel teeth.

With two adjustable blades, these saws cut a variety of hole sizes in ceilings, walls, floors, and other surfaces made of drywall, plaster, plastic, and wood. To block flying chips and collect dust, they have a clear debris shield.

The diamond-grit edge on these hole saws cuts more accurately, leaves a smoother finish, and lasts up to twice as long as carbide-grit-coated teeth.

The saws in these kits have carbide-tipped teeth, so they last up to twice as long as saws with high-speed steel teeth.

The saws in these kits have carbide-grit-coated teeth that cut ceramic tile, fiberglass, masonry, plastic, and composites.

Combine the cutting base and a corner punch to make rounded corners in sheet metal.

With an internal spring mechanism, these punches offer one-hand operation when marking hole centers.

Also known as center punches, strike these with a hammer to mark hole centers in metal and other materials.

Strike these Starrett punches with a hammer to mark hole centers in metal and other materials. Also known as center punches.

Ground to a sharper tip than other center-marking punches, these tools make the precision marks required for the intersection of lines and other detailed tasks. They're also known as prick punches.

Fit these through existing holes and mark the center of the hole in a second workpiece.

Also known as blind-hole spotters, these punches fit into closed-end holes and mark the center of a complementary hole.

These sets come with three punches for use with a variety of hole sizes. Insert one into an existing hole and twist the handle to open the end of the punch. The point automatically centers once the punch has fit the hole size.

Push down on the spring-loaded cone to center the punch in a variety of round and square hole sizes.

Also known as transfer screws, the punches in these sets can be used in any threaded hole to transfer the hole location. Use the handle to screw a punch into a hole.

The punches in these sets have a uniform shoulder height so you can quickly transfer multiple hole locations at once. Also known as transfer screws.

An insulated handle and shaft protects against shock from accidental contact with live electrical circuits. These awls are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

Make marks on surfaces with a Rockwell hardness up to C30, including leather, wood, and most metals. Stamps are steel.

The thick shank provides more control and consistent marks than our standard metal stamps. Make marks on surfaces with a Rockwell hardness up to C30, including leather, wood, and most metals. Stamps are steel.

Make marks on surfaces with a Rockwell hardness up to C50, including stainless steel and heat-treated steel.

These stamps have a solid face.

These stamps have a border around the characters to help them stand out.

These steel stamps are strong enough to make marks on surfaces with a Rockwell hardness up to C50, including stainless steel and heat-treated steel.

Made from 440C stainless steel, these stamps won't rust and flake with exposure to moisture and chemicals. They're strong enough to make marks on surfaces with a Rockwell hardness up to C50, including other stainless steels and heat-treated steel.

Make marks on surfaces with a Rockwell hardness up to C30, including leather, wood, and most metals.