Repair and rebuild metal surfaces that are exposed to heat. These surface fillers withstand temperatures over 450° F. Fillers that have a mix ratio are multi-part fillers. The size listed is the combined total of the parts.

Surface fillers in a stick have a resin on the outside and a hardener on the inside. Cut the desired amount from the sticks, knead to a uniform color to mix, and press into place.

Surface fillers in a syringe come with everything you need to make repairs.

Chemicals will not affect these two-part epoxies. They repair cracked, worn, and damaged surfaces. The size listed is the combined total of the two parts.

For use in processing equipment that carries particles smaller than 1/16" in diameter, these ceramic-filled epoxies rebuild and repair surfaces exposed to abrasion from particles, such as dust collectors, fan blades, and fan housings. The size listed is the combined total of the two parts.

For use in processing equipment that carries large particles 1/16" in diameter and larger, these ceramic-filled epoxies rebuild and repair surfaces exposed to abrasion from particles, such as pump housings, chute linings, and hoppers. The size listed is the combined total of the two parts.

These rubber-filled epoxies have excellent wear and impact resistance. Use them to repair and rebuild surfaces such as pump liners, hoppers, and vibrating feeders. The size listed is the combined total of the two parts.

To stop leaks in metal tanks and equipment without draining the contents, rub the smaller stick into the leak until it stops. Then, cut the desired amount from the larger stick, knead to a uniform color to mix, and press into place. The size listed is the combined total of the two parts.

To stop leaks in metal tanks and equipment without draining the contents, heat the area with a heat gun or torch to melt the stick and form a permanent seal. The resulting patch can withstand pressure up to 600 psi. These sticks meet NSF/ANSI 61 safety standards for use with drinking water systems.

Stop leaks in metal tanks and equipment without draining the contents. Until a permanent repair can be made, rub these sticks into the leak to form a temporary seal.

Repair stripped threads on female connections, such as oil pans, valve covers, and distributor caps. Apply the included release agent to a male fastener that fits your female connection. Then mix the two-part filler and apply to the stripped threads. Screw in the male fastener, let it set up for five minutes, and remove. The new threads can be used in two hours. The container size listed is the combined total of the two-part filler.

These surface fillers can be used on vertical surfaces without sagging. They repair cracked, worn, and damaged surfaces. The size listed is the combined total of the two parts.

Devcon Plastic Steel® Liquid can repair areas where brazing and welding is impractical.

Devcon Metal Patch & Fill repairs worn, rusted, and corroded surfaces with less preparation.

Surface fillers in one-time-use packets are also known as double-bubbles.

Knead the epoxy-coated patch and resin together to make repairs to pipes, tanks, drums, and containers in the field.

Make castings and fill voids with these two-part pourable epoxies. The size listed is the combined total of the two parts.

Press these putty surface fillers in place to fill in holes, cracks, and dents. When exposed to sunlight or a UV lamp, they begin to harden immediately.

Epoxy fillers provide better adhesion and more corrosion resistance than polyester fillers.

Mix these two-part epoxy surface fillers to create a strong repair in wet environments or underwater. Use them to repair cracked, worn, and damaged surfaces. Size listed is the combined total of the two parts.

Putty fillers come in a stick with a resin on the outside and a hardener on the inside. Cut the desired amount from the sticks, knead to a uniform color to mix, and press into place. NSF/ANSI 61 surface fillers meet safety standards for use with drinking water.

Paste fillers resist alkalies, solvents, gasoline, and oil.

Also known as sloshing compounds, these two-part epoxies bond to rough and rusty surfaces in fuel tanks to repair leaks and prevent further corrosion. They withstand permanent immersion in fuel, oil, and harsh solvents. Use them with metal, plastic, and fiberglass tanks. Mix the smaller can with the bigger one and pour into your fuel tank. Rotate the tank to coat the interior and dump out any excess. Allow to cure overnight. Size listed is the combined total of the two parts.

1.5-pint container can treat a 10-gallon fuel tank. 3-pint container can treat a 20-gallon fuel tank.

This putty-like glue cures into a pliable rubber. Use it to repair seals and cracks, or mold it into hooks and bumpers.

Pull off a small piece of putty and stick lightweight objects to your surface. It removes without leaving stains or residue on most surfaces and is reusable.

Temporarily stabilize objects on flat surfaces with this clear adhesive gel. It removes cleanly from most surfaces with a twist, and it won't dry out so it can be used again.

These machinable epoxies are mixed with metal so they can be used to repair cracks and threaded holes. The strongest and most weather- and chemical-resistant structural adhesives, epoxies work especially well on metals.

The size listed is the combined total of the two parts. For putty adhesives, slice off the required amount, then knead it together to form a moldable adhesive.

1751 and epoxy in 11-oz. tubes are reinforced with aluminum.

8267 is reinforced with steel, but won't rust.

Epoxies are the strongest and most weather- and chemical-resistant structural adhesives. They work especially well on metals. For putty adhesives, slice off the required amount, then knead it together to form a moldable adhesive.

Even when used under water, these adhesives maintain their strength. The most weather- and chemical-resistant structural adhesives, epoxies tend to work especially well on metals.

The size listed is the combined total of the two parts. For putty adhesives, slice off the required amount, then knead it together to form a moldable adhesive.

WaterWeld and 11800, as well as one-time-use packets, can be applied to wet surfaces or under water.

To allow time to adjust and position parts, these epoxies remain workable for at least 90 minutes. The strongest and most weather- and chemical-resistant structural adhesives, epoxies work especially well on metals.

The size listed is the combined total of the two parts.

For quick repairs, these epoxies begin to harden in 6 minutes or less. Epoxies are the strongest and most weather- and chemical-resistant structural adhesives.

The size listed is the combined total of the two parts.

50132 works especially well on plastics and composites.

Urethane adhesives are the most flexible, so they bond dissimilar materials and damp vibration.

The size listed is the combined total of the two parts.

Also known as thumb-grade caulk, this forms a non-hardening, moisture-resistant seal that remains pliable.

Butyl rubber has a sticky, gummy consistency.

Butyl mastic has a clay-like consistency.