Use these valves with garden hose and other landscaping equipment. They’re for use with water, air, and inert gas.

Install these low-profile valves in tight spots. They are for use with water, oil, air, and inert gas.

Plastic provides a lightweight and economical alternative to metal. All valves have barbs that grip onto tubing for a secure hold. They’re for use with water, oil, air, and inert gas.

For fast installation and removal from pipelines, these valves have union fittings that disassemble into multiple pieces. Insert unthreaded pipe into the socket ends and bond with primer and cement to create a permanent, leak-tight connection. These valves meet NSF/ANSI 61 for use in drinking water lines.

Disassemble the union fittings on these valves for fast installation and removal from your pipeline. All meet NSF/ANSI 61 for use with drinking water.

For chemical-processing applications in confined areas, these valves have an EPDM seal and a PVC or CPVC body to withstand aggressive and corrosive solutions and a low-profile handle to fit in tight spots.

Union fittings on both ends of these valves disassemble for fast installation and removal from your pipeline. Insert unthreaded pipe into the socket ends and bond with primer and cement to create a permanent, leak-tight connection. These valves have a fluoroelastomer seal and a plastic body that can withstand aggressive and corrosive solutions in chemical-processing applications.

Insert tubing into the fittings on these valves—no heat, solder, or flux required. To withstand aggressive and corrosive solutions, they have a chemical-resistant fluoroelastomer seal and a plastic body.

These valves have socket-weld connections for bonding to unthreaded male plastic pipe.

These valves have NPT connections for use with threaded pipe.

These top-of-the-line valves are comparable to Asco Red Hat 8210G Series and Parker Gold Ring 23C Series.

Control flow in high-pressure lines in tight spots—these valves have the highest pressure ratings of our compact valves.

Less than half the size of our other compact valves, these have small pipe connections for miniature lines.

To fit in tight spots, these valves have a slimmer body than standard valves with an exhaust port.

These valves are rated for use in hazardous locations with flammable gas and combustible dust.

Avoid pressure surges and system shocks that can damage piping by installing these valves that open and close slowly.

A built-in strainer traps debris and allows you to replace the screen without disconnecting your pipeline.

Often used to control single-acting, spring-return air cylinders, these valves have a third threaded port to exhaust media.

To change the flow rate of antifreeze and cleaning solutions, use the adjustment screw or knob to manually set how much these valves will open when actuated.

Built to withstand the extreme cold of liquid nitrogen and liquid oxygen, these valves are cleaned and bagged for high-purity applications.

Insert tubing into the fittings on these valves—no heat, solder, or flux required.

Install these valves in gas pipelines to automatically control the flow of natural gas, propane, and butane to equipment.

With a plastic body and a fluoroelastomer seal, these valves can stand up to aggressive and corrosive solutions in chemical-processing applications.

Supply fuel oil to boilers, furnaces, and other equipment.

Also known as piston valves, these have a compact, lightweight actuator that allows them to be installed in any mounting orientation. They’re often used in water-treatment applications.

Insert unthreaded pipe into the socket ends and bond with PVC primer and cement to create a permanent, leak-tight connection.

All valves have threaded NPT connections.

For a lightweight and corrosion-resistant alternative to metal valves, these have a plastic body. To create a permanent, leak-tight connection, insert unthreaded pipe into the socket ends and bond with PVC primer and cement. These valves are for use with oil. They gradually open and close to adjust and regulate flow.

Insert tubing into the fittings on these valves—no heat, solder, or flux required. They’re for use with water, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Use these valves with NPT threaded pipe. They have a fluoroelastomer seal and a plastic body to withstand aggressive and corrosive solutions in chemical-processing applications. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

These valves have barbed fittings that grip onto tubing, providing a secure hold. They’re often used in food and beverage tubing lines to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

In addition to fluoroelastomer seats that resist a wide range of chemicals, these valves have no metal parts to corrode, so they’re often used for chemical-processing applications in corrosive conditions. All bolt to flanges to adjust and regulate flow in flanged pipelines.

Available in smaller pipe sizes than other solenoid flow-adjustment valves, these are often used with gas chromatography equipment and analytical instrumentation. They adjust and regulate flow based on the intensity of the electrical signal into the valve. They're often integrated into PLC systems for automatic control over the valve position based on system conditions.

For easy installation and removal from pipelines, all ends on these valves have union fittings that disassemble into multiple pieces. Use with water. Valves divert flow between ports.

Barbs grip onto tubing, providing a secure hold. Use with water, oil, air, and inert gas. These valves divert flow between ports in tubing lines.

To divert flow between ports in drinking water lines, these valves meet NSF/ANSI 61.

These valves operate on electricity to automatically divert flow between ports. Use with water, oil, air, and inert gas.

Often used for emission analysis and gas processing, these valves attach to each other horizontally to create one centralized manifold for servicing multiple process lines. All are rated for use with water, oil, air, and inert gas. They operate on electricity to automatically divert flow between ports.

Barbs grip onto tubing, providing a secure hold.

Also known as backwater valves, these valves prevent backflow of sewage and wastewater in drain, waste, and vent systems.

These valves open to allow flow in one direction and close when flow stops or reverses.

Body is plastic.

A plastic body withstands pH neutralizing, cleaning, and plating solutions containing sodium hydroxide, methyl ethyl ketone, and other harsh chemicals.

Run through equipment cycles up to 30% faster than with standard valves. These valves shift between flow positions in 1.7 ms. Also known as 3/2 valves, they create one action, such as extending a cylinder. Apply voltage to the electrical connection to actuate.

Often used to extend and then retract a cylinder at different speeds, these valves create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as 5/2 valves, they actuate when voltage is applied to the electrical connection.

In the off position, these valves exhaust all air pressure, allowing the equipment to return to the neutral position. Often used to extend and then retract a cylinder at different speeds, they create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Apply voltage to the electrical connection to actuate.

Also known as 4-way valves, these valves create two actions, such as extending and then retracting a double-acting cylinder. Apply voltage to the electrical connection to actuate.

Use a single valve to create motion and control the speed of that motion.

These valves are rated for environments where hazardous material is present. They actuate when voltage is applied to the electrical connection.

With two 3-way integrated solenoid valves, these electrically controlled valves direct airflow to end-of-arm tools that don’t require vacuum suction, such as pick-and-place grippers. Also known as 3/2 valves, each of the two solenoid valves directs air to a different port.

Mix and match valve styles on one manifold to meet your control needs. Mount multiple valves to a manifold to reduce piping requirements and create multiple actions from a single pressure input.

With two 2-way integrated solenoid valves, these electrically controlled valves direct airflow to venturi pumps, which generate the suction you need to run end-of-arm tools, such as vacuum cups.

Convert a continuous stream of air into a series of quick pulses, reducing air consumption by up to 50% and improving performance in air-blowing applications such as cleaning and drying.

Also known as Monday-morning valves, these valves slowly introduce pressure to reduce surge damage during start-up.

Also known as Monday-morning valves, these valves slowly introduce pressure to reduce surge damage during start-up.