Use these valves with water, air, and inert gas.

These valves have union fittings that disassemble for fast installation and removal from pipelines. Use with water, air, and inert gas.

Insert tubing into the fittings on these valves—no heat, solder, or flux required. They’re for use with water, oil, air, and inert gas.

Insert unthreaded pipe into the socket ends and bond with primer and cement to create a permanent, leak-tight connection. These valves meet NSF/ANSI 61, which means they’re safe to use with drinking water systems.

These valves meet NSF/ANSI 61 for use in drinking water lines.

With a fluoroelastomer seal and a CPVC body, these valves can withstand aggressive and corrosive solutions in chemical-processing applications.

For fast installation and removal from pipelines, these valves have union fittings that disassemble into multiple pieces. All have a fluoroelastomer seal and a plastic body that can stand up to aggressive and corrosive solutions in chemical-processing applications.

Insert unthreaded pipe into the socket ends and bond with primer and cement to create a permanent, leak-tight connection. These valves have a fluoroelastomer seal and a plastic body that can withstand aggressive and corrosive solutions in chemical-processing applications.

For use with threaded pipe, these valves have NPT connections.

These valves have NPT connections for use with threaded pipe.

With a plastic body and a fluoroelastomer seal, these valves can stand up to aggressive and corrosive solutions in chemical-processing applications.

Also known as actuated ball valves, these provide higher flow rates than other air-driven valves.

Insert unthreaded pipe into the socket ends and bond with PVC primer and cement to create a permanent, leak-tight connection.

Plastic provides a lightweight and corrosion-resistant alternative to metal. Use with oil. These valves gradually open and close to adjust and regulate flow.

Often used in low-pressure water pipelines, these valves have a plastic body for the lightest weight of our flanged flow-adjustment valves. Use them with water. They bolt to flanges to adjust and regulate flow in flanged pipelines.

These valves meet NSF/ANSI 61 for use with drinking water. They bolt to flanges to adjust and regulate flow in flanged pipelines.

Insert tubing into the fittings on these valves—no heat, solder, or flux required. They’re for use with water, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Use these valves with NPT threaded pipe. They have a fluoroelastomer seal and a plastic body to withstand aggressive and corrosive solutions in chemical-processing applications. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

For a lightweight alternative to metal valves, these have a plastic body. To fit in tight spots, they have a low-profile handle and a short end-to-end length. Valves are for use with water, oil, air, and inert gas. All divert flow between ports.

Insert tubing into the fittings on these valves—no heat, solder, or flux required. All are for use with water, oil, air, and inert gas. They divert flow between ports in tubing lines.

For easy installation and removal from pipelines, all ends on these valves have union fittings that disassemble into multiple pieces. Their fluoroelastomer seal and plastic body can withstand aggressive and corrosive solutions for diverting flow between ports in chemical-processing applications.

Plastic provides a lightweight alternative to metal.

Insert tubing into the fitting—no heat, solder, or flux required.

Also known as backwater valves, these valves prevent backflow of sewage and wastewater in drain, waste, and vent systems.

To reduce installation time and allow for maintenance without detaching pipe connections, these valves have union fittings.

Visually inspect flow and debris accumulation through the transparent valve body.

Insert unthreaded pipe into the socket ends and bond with primer and cement to create a permanent, leak-tight connection.

With a three-port design, these valves allow inline flow from the inlet to the outlet during normal conditions and divert flow through the relief port in overpressure conditions. They are often used with feed pumps for fertilizers and bleach.

A plastic body and fluoroelastomer seal stand up to harsh chemicals.