Filter by
    Reamer Diameter
    System of Measurement
    Reamer Size
    For Use On
    Flute Style
    Shank Type
    Material
    Reamer Type
    Number of Flutes
    Overall Length
    Flute Length
    DFARS (Defense Acquisition Regulations System)
    Industrial Info Snippet
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Comments
    E-mail address (if you would like a response)
    3 Products

    Reamers

    Enlarge holes to exact inch, metric, wire gauge, or letter sizes. Reamers also smooth the walls of holes. Note: Never rotate the reamer in the reverse direction of the cut. This will ruin its accuracy.
    3D CAD models availableFor technical drawings and 3-D models, click on a part number.
    Round Shank
    The most common shank type, it fits in the chuck of drill presses, turret lathes, and other machine and power tools. Also known as chucking reamers.
    Use high-speed steel reamers for general purpose reaming on a wide variety of materials.
    Cobalt steel reamers offer better heat and abrasion resistance than high-speed steel reamers to run up to 25% faster for a longer tool life. They're commonly used on hard-to-machine materials such as nickel alloys, stainless steel, and titanium.
    The most common shank type, it fits in the chuck of drill presses, turret lathes, and other machine and power tools. Also known as chucking reamers.
    Reamer
    Size
    Reamer
    Diameter
    Material
    Flute
    Length
    Overall
    Length
    Number
    of
    Flutes
    Cutting
    Diameter
    Tolerance
    For Use On
    Each
    Straight flutes are used for general purpose cutting. Since chips are forced forward into the hole, they perform best in through-hole applications.
    62 ga0.0380"High-Speed Steel1/2"2 1/2"40" to 0.0002"Aluminum, Brass, Bronze, Iron, Plastic, Stainless Steel, Steel8930A111$14.34
    62 ga0.0380"Cobalt Steel1/2"1 1/2"30" to 0.0002"Aluminum, Brass, Bronze, Hardened Steel, Iron, Nickel, Plastic, Stainless Steel, Steel, Titanium, Tool Steel2733A89119.60

    Reamer Sets

    Keep a variety of reamer sizes on hand for enlarging holes to exact inch, metric, or wire gauge sizes. Reamers also smooth the walls of holes. Note: Never rotate the reamer in the reverse direction of the cut. This will ruin its accuracy.
    3D CAD models availableFor technical drawings and 3-D models, click on a part number.
    Round Shank
    With Metal Case (29 Pieces)
    With Wood Case (29 Pieces)
    With Roll Pouch
    With Wood Case (13 Pieces)
    With Metal Case (25 Pieces)
    With Metal Case (20 Pieces)
    With Metal Case (60 Pieces)
    The most common shank type, it fits in the chuck of drill presses, turret lathes, and other machine and power tools. Also known as chucking reamers.
    Use high-speed steel reamers for general purpose reaming on a wide variety of materials.
    The most common shank type, it fits in the chuck of drill presses, turret lathes, and other machine and power tools. Also known as chucking reamers.
    Sizes
    Included
    Number
    of
    Pieces
    Material
    Container
    Type
    For Use On
    Set
    Straight flutes are used for general purpose cutting. Since chips are forced forward into the hole, they perform best in through-hole applications.
    80-61 ga20High-Speed SteelMetal CaseAluminum, Brass, Bronze, Iron, Plastic, Stainless Steel, Steel3008A5$436.24