Filter by
Reamer Diameter
System of Measurement
Reamer Size
For Use On
Flute Style
Shank Type
Material
Reamer Type
Number of Flutes
Overall Length
Flute Length
DFARS (Defense Acquisition Regulations System)
Shank Diameter
Spiral Direction
Application
Reamers
Enlarge holes to exact inch, metric, wire gauge, or letter sizes. Reamers also smooth the walls of holes. Note: Never rotate the reamer in the reverse direction of the cut. This will ruin its accuracy.
For technical drawings and 3-D models, click on a part number.Round Shank
The most common shank type, it fits in the chuck of drill presses, turret lathes, and other machine and power tools. Also known as chucking reamers.
Use high-speed steel reamers for general purpose reaming on a wide variety of materials.
Cobalt steel reamers offer better heat and abrasion resistance than high-speed steel reamers to run up to 25% faster for a longer tool life. They're commonly used on hard-to-machine materials such as nickel alloys, stainless steel, and titanium.
Carbide reamers are harder, stronger, and more wear resistant than carbide-tipped reamers for the highest accuracy. Use on hard and abrasive materials such as cast iron, nonferrous alloys, plastic, and hardened steel. Not for use with hand-held tools, they require rigid tool holding to prevent breakage.
Right-hand spirals pull chips upward as they cut, so they’re often used in blind holes.
The most common shank type, it fits in the chuck of drill presses, turret lathes, and other machine and power tools. Also known as chucking reamers.
Reamer Size | Reamer Diameter | Material | Flute Length | Overall Length | Number of Flutes | Spiral Direction | Cutting Diameter Tolerance | For Use On | Each | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Straight flutes are used for general purpose cutting. Since chips are forced forward into the hole, they perform best in through-hole applications. | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 13/64" | 0.2031" | High-Speed Steel | 1 1/4" | 5" | 6 | __ | 0" to 0.0002" | Aluminum, Brass, Bronze, Iron, Plastic, Stainless Steel, Steel | 2995A118 | $19.34 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 13/64" | 0.2031" | Cobalt Steel | 1 1/4" | 5" | 6 | __ | 0" to 0.0002" | Aluminum, Brass, Bronze, Hardened Steel, Iron, Nickel, Plastic, Stainless Steel, Steel, Titanium, Tool Steel | 2975A57 | 27.17 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 13/64" | 0.2031" | Carbide | 1" | 3" | 4 | __ | 0" to 0.0002" | Aluminum, Brass, Bronze, Fiberglass, Hardened Steel, Iron, Nickel, Plastic, Stainless Steel, Steel, Titanium, Tool Steel | 3026A24 | 45.97 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Spiral flutes clear chips better than straight flutes. The choice for keyways and other applications with a break in the hole's surface. | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 13/64" | 0.2031" | High-Speed Steel | 1 1/4" | 5" | 6 | Right Hand | 0" to 0.0002" | Aluminum, Brass, Bronze, Iron, Plastic, Stainless Steel, Steel | 3106A21 | 21.35 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Threaded Shank with Built-In Pilot
Use with power drills that have a 1/4"-28 threaded spindle or adapter. A built-in pilot maintains alignment in the hole.
Use high-speed steel reamers for general purpose reaming on a wide variety of materials.
Use with power drills that have a 1/4"-28 threaded spindle or adapter. A built-in pilot maintains alignment in the hole.
Reamer Size | Reamer Diameter | Pilot Diameter | Material | Thread Size | Flute Length | Pilot Length | Overall Length | Number of Flutes | Pilot Chamfer Angle | Cutting Diameter Tolerance | Pilot Cutting Tolerance | For Use On | Each | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Straight flutes are used for general purpose cutting. Since chips are forced forward into the hole, they perform best in through-hole applications. | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 13/64" | 0.2031" | 0.194" | High-Speed Steel | 1/4"-28 | 1 1/8" | 1/4" | 2 3/8" | 6 | 45° | 0" to 0.0002" | -0.001" to 0" | Aluminum, Brass, Bronze, Iron, Plastic, Stainless Steel, Steel | 2585A27 | $49.05 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Hole-Alignment Reamers
Straighten, enlarge, and deburr misaligned and overlapping holes. Also known as bridge, car, and aligning reamers, they have a tapered tip for easy entry into misaligned holes. Note: Never rotate the reamer in the reverse direction of the cut. This will ruin its accuracy.
Round Shank
The most common shank type, it fits in the chuck of drill presses, turret lathes, and other machine and power tools. Also known as chucking reamers.
Use high-speed steel reamers for general purpose reaming on a wide variety of materials.
Left-hand spirals push chips downward as they cut, so they’re often used in through holes.
The most common shank type, it fits in the chuck of drill presses, turret lathes, and other machine and power tools. Also known as chucking reamers.
Reamer Size | Reamer Diameter (A) | Reamer Diameter (B) | Material | Flute Length | Overall Length | Spiral Direction | Cutting Diameter Tolerance | For Use On | Each | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Spiral flutes clear chips better than straight flutes. The choice for keyways and other applications with a break in the hole's surface. | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 9/16" | 0.5625" | 0.2031" | High-Speed Steel | 1 5/8" | 3 1/2" | Left Hand | 0" to 0.0050" | Aluminum, Brass, Bronze, Iron, Plastic, Stainless Steel, Steel | 3411N11 | $53.43 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Reamer Sets
Keep a variety of reamer sizes on hand for enlarging holes to exact inch, metric, or wire gauge sizes. Reamers also smooth the walls of holes. Note: Never rotate the reamer in the reverse direction of the cut. This will ruin its accuracy.
For technical drawings and 3-D models, click on a part number.Round Shank
With Metal Case (29 Pieces)
With Wood Case (29 Pieces)
With Roll Pouch
With Wood Case (13 Pieces)
With Metal Case (25 Pieces)
With Metal Case (20 Pieces)
With Metal Case (60 Pieces)
The most common shank type, it fits in the chuck of drill presses, turret lathes, and other machine and power tools. Also known as chucking reamers.
Use high-speed steel reamers for general purpose reaming on a wide variety of materials.
Right-hand spirals pull chips upward as they cut, so they’re often used in blind holes.
The most common shank type, it fits in the chuck of drill presses, turret lathes, and other machine and power tools. Also known as chucking reamers.
Sizes Included | Number of Pieces | Material | Spiral Direction | Container Type | For Use On | Set | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Straight flutes are used for general purpose cutting. Since chips are forced forward into the hole, they perform best in through-hole applications. | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 1/16"-1/2" (increments of 1/64") | 29 | High-Speed Steel | __ | Metal Case | Aluminum, Brass, Bronze, Iron, Plastic, Stainless Steel, Steel | 3008A17 | $754.51 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 1/16"-1/2" (increments of 1/64") | 29 | High-Speed Steel | __ | Wood Case | Aluminum, Brass, Bronze, Iron, Plastic, Stainless Steel, Steel | 3008A8 | 781.88 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Spiral flutes clear chips better than straight flutes. The choice for keyways and other applications with a break in the hole's surface. | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 1/16"-1/2" (increments of 1/64") | 29 | High-Speed Steel | Right Hand | Metal Case | Aluminum, Brass, Bronze, Iron, Plastic, Stainless Steel, Steel | 3008A9 | 873.53 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Drill-Length Reamer Sets
Shorter than standard-length reamers for rigidity, these can be used in the same tools as jobbers' drill bits to size and smooth holes. Sets include a variety of reamer sizes. Note: Never rotate the reamer in the reverse direction of the cut. This will ruin its accuracy.
For technical drawings and 3-D models, click on a part number.Round Shank
13-Piece Set
29-Piece Set
26-Piece Set
60-Piece Set
15-Piece Set
The most common shank type, it fits in the chuck of drill presses, turret lathes, and other machine and power tools. Also known as chucking reamers.
Use high-speed steel reamers for general purpose reaming on a wide variety of materials.
The most common shank type, it fits in the chuck of drill presses, turret lathes, and other machine and power tools. Also known as chucking reamers.
Sizes Included | Number of Pieces | Material | Container Type | For Use On | Set | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Straight flutes are used for general purpose cutting. Since chips are forced forward into the hole, they perform best in through-hole applications. | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 1/16"-1/4" (increments of 1/64") | 13 | High-Speed Steel | Metal Case | Aluminum, Brass, Bronze, Iron, Plastic, Stainless Steel, Steel | 3008A1 | $194.94 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 1/16"-1/2" (increments of 1/64") | 29 | High-Speed Steel | Metal Case | Aluminum, Brass, Bronze, Iron, Plastic, Stainless Steel, Steel | 3008A2 | 604.85 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||