Connect two differently sized male-threaded parts, such as threaded rods, and tighten with a standard wrench. The threads on these adapters have various sizes and spacing, so you can increase or decrease thread size or adapt from coarse to fine threading. You can also use them to change the gender of a connection from male to female. Small adapters can work as threaded standoffs, which position and separate circuit boards and other components in assemblies.

Choose black-oxide steel adapters to match the aesthetics of your system or for their mild corrosion resistance. The finish won't chip or rub off. They resist rust in indoor and dry environments, but avoid using them in corrosive environments.

Zinc-plated steel adapters are a good option in dry environments. The zinc plating prevents the steel from corroding until the plating wears away.

18-8 stainless steel adapters resist corrosion caused by water. They're good for wet and damp environments but will corrode when exposed to salt water and other chloride solutions.

316 stainless steel adapters have the best corrosion resistance. They stand up to wet environments, just like 18-8 stainless steel adapters, but unlike 18-8 stainless steel adapters, they resist corrosion caused by salt water and harsh chemicals.

At about a third of the weight of steel adapters, aluminum adapters are the lightest we offer. They resist corrosion in wet environments.

For technical drawings and 3-D models, click on a part number.

Made of 18-8 stainless steel, these inserts have good corrosion resistance. Also known as E-Z Lok, they use Loctite® adhesive to keep them in place. The adhesive reaches full strength after 72 hours. They may be mildly magnetic. Installation requires a drill bit and a standard tap. Then set the insert with an installation bit, a slotted screwdriver, or a bolt with two nuts.

Choose inserts with a thick wall for greater strength than thin-wall inserts, or to fill a large hole.

For technical drawings and 3-D models, click on a part number.

A black-phosphate finish provides mild corrosion resistance. Also known as E-Z Lok, these inserts use Loctite® adhesive to keep them in place. The adhesive reaches full strength after 72 hours. Installation requires a drill bit and a standard tap. Then set the insert with a bolt and two nuts, or use an installation bit.

Choose inserts with a thick wall for greater strength than thin-wall inserts, or to fill a large hole.

To drive slotted inserts, you can use a slotted screwdriver instead of using an installation bit or a bolt and two nuts.

For technical drawings and 3-D models, click on a part number.

These inserts are the most corrosion-resistant thread-locking inserts we offer. Also known as E-Z Lok, they use Loctite® adhesive to keep them in place. The adhesive reaches full strength after 72 hours. All have thick walls for strength and can be used to fill a large hole with stripped threads. They may be mildly magnetic. Installation requires a drill bit and a standard tap. Then set the insert with an installation bit, a slotted screwdriver, or a bolt with two nuts.

For technical drawings and 3-D models, click on a part number.

These assortments include various sizes of thread-locking inserts. Also known as E-Z Lok, they use Loctite® adhesive to keep them in place. The adhesive reaches full strength after 72 hours. All inserts have thick walls for strength and can be used to fill a large hole.

Black-phosphate steel inserts are mildly corrosion resistant.

A black-phosphate finish provides mild corrosion resistance. Drive the keys into the surrounding material for a more secure hold than thread-locking inserts. Use them to repair or change threads in soft metals such as aluminum. They’re comparable to Keensert® inserts. Installation requires a drill bit, a standard tap, an installation tool, and a hammer.

Choose inserts with a thick wall for greater strength than thin-wall inserts, or to fill a large hole with stripped threads.

Inserts with an extra thick wall are stronger than thick- and thin-wall inserts. Use them to reduce the size of tapped holes.

For technical drawings and 3-D models, click on a part number.

Made of stainless steel, these inserts have good corrosion resistance. Drive the keys into the surrounding material for a more secure hold than thread-locking inserts. Use them to repair or change threads in soft metals such as aluminum. Inserts may be mildly magnetic. They’re comparable to Keensert® inserts. Installation requires a drill bit, a standard tap, an installation tool, and a hammer.

Choose inserts with a thick wall for greater strength than thin-wall inserts, or to fill a large hole.

Inserts with an extra-thick wall are stronger than thick- and thin-wall inserts. Use them to reduce the size of tapped holes.

For technical drawings and 3-D models, click on a part number.

These inserts are made to stringent military specifications. Drive the keys into the surrounding material for a more secure hold than thread-locking inserts. Use them to repair or change threads in soft metals such as aluminum. Inserts may be mildly magnetic. They’re comparable to Keensert® inserts. Installation requires a drill bit, a standard tap, an installation tool, and a hammer.

Choose inserts with a thick wall for greater strength than thin-wall inserts, or to fill a large hole.

For technical drawings and 3-D models, click on a part number.

The strongest key-locking inserts we offer, these inserts are made to stringent military specifications. Drive the keys into the surrounding material for a more secure hold than thread-locking inserts. Use them to repair or change threads in soft metals such as aluminum. Inserts may be mildly magnetic. They’re comparable to Keensert® inserts. Installation requires a drill bit, a standard tap, an installation tool, and a hammer.

Choose inserts with a thick wall for greater strength than thin-wall inserts, or to fill a large hole.

For technical drawings and 3-D models, click on a part number.

With a distorted internal thread and keys on the outside, these inserts create a strong hold on both fasteners and surrounding material. Together, the distorted thread and keys create a mechanical lock that resists pull-out from vibration or temperature changes and is stronger than inserts that require threadlocker. Use them to create completely new threads, add strong threads in soft metal, or replace existing threads that are damaged or need to be resized. They're often seen in molds, tools and dies, and suspension systems in vehicles.

Made of a solid piece of metal, these inserts are also stronger than helical inserts, which are made of coiled wire. A dry-film lubricant makes it easy to install them and to screw fasteners into them. All are made to tight tolerances with strictly controlled materials; many inch sizes also meet military or aerospace standards for dimensions and material.

To install, you'll need a tap to create the threads in your material, and an installation tool and a hammer to drive the keys into the material.

When choosing between stainless steel and cadmium-plated steel, consider strength and price. Both materials withstand wet environments. Stainless steel inserts are economical, but not as strong as steel. Use cadmium-plated steel inserts in applications where additional strength is necessary, such as in engine blocks. Steel inserts are stronger than stainless steel inserts, but are more expensive.

Inserts with thick walls are the most commonly used; they’re stronger than thin-wall inserts and are used in larger holes. Inserts with extra-thick walls are the strongest; use them to reduce the size of tapped holes.

For technical drawings and 3-D models, click on a part number.

Drive the keys into the surrounding material for a more secure hold than thread-locking inserts. These inserts are used to repair or convert threads in soft metals such as aluminum. They’re comparable to Keensert® inserts.

18-8 stainless steel inserts are more corrosion resistant than black-phosphate steel. They may be mildly magnetic.

Black-phosphate steel inserts are mildly corrosion resistant.

Choose inserts with a thick wall for greater strength than thin-wall inserts, or to fill a large hole.

Inserts with an extra thick wall are stronger than thick- and thin-wall inserts. Use them to reduce the size of tapped holes.

These assortments include various sizes of key-locking inserts with thick and thin walls, and an installation tool. Drive the keys into the surrounding material for a more secure hold than thread-locking inserts. Use them to repair or convert threads in soft metals such as aluminum. They’re comparable to Keensert® inserts.

18-8 stainless steel inserts are more corrosion resistant than black-phosphate steel. They may be mildly magnetic.

Black-phosphate steel inserts are mildly corrosion resistant.

Choose assortments with thick-wall inserts for greater strength than thin-wall inserts, or to fill a large hole.

Also known as Heli-Coil inserts, these inserts have coils that expand once installed to securely anchor the insert. All have a prong for ease of installation. An installation tool grips the prong and reduces the coil diameter, enabling the insert to fit in tapped holes. Remove the prong to insert the screw. Installation requires a drill bit, a helical insert tap, an installation tool, and a prong break-off tool.

For technical drawings and 3-D models, click on a part number.

A distorted thread grips the screw to resist loosening. Also known as Heli-Coil inserts, these inserts have coils that expand once installed to securely anchor the insert. All have a prong for ease of installation. An installation tool grips the prong and reduces the coil diameter, enabling the insert to fit in tapped holes. Remove the prong to insert the screw. Installation requires a drill bit, a helical insert tap, an installation tool, and a prong break-off tool.

For technical drawings and 3-D models, click on a part number.

Inserts come with a through-hole tap and installation tool. Also known as Heli-Coil inserts, they have coils that expand once installed to securely anchor the insert. All have a prong for ease of installation. An installation tool grips the prong and reduces the coil diameter, enabling the insert to fit in tapped holes. Remove the prong to insert the screw.