Also known as Pressure Class 150 flanges, these corrosion-resistant flanges are designed for low-pressure pipe applications.

These fittings are made to tighter tolerances than other stainless steel pipe fittings. They are also known as instrumentation fittings.

Use these heavy duty, corrosion-resistant fittings in high-pressure flow applications.

Choose these fittings when you want the same high-quality found in our low-pressure pipe fittings, but need more strength to handle higher pressures.

Press these fittings onto stainless steel pipe using a crimping tool for a permanent, leak-tight connection that's faster than threading or welding and doesn't require heat.

These flanges are for low-pressure applications in noncorrosive environments.

The galvanized finish on these fittings provides fair corrosion resistance. Fittings are for use in low-pressure applications.

A galvanized finish gives these fittings better corrosion resistance than our plain steel high-pressure fittings. Also known as Pressure Class 3000 fittings.

Made to tighter tolerances than other steel pipe fittings, these are also known as instrumentation fittings.

A galvanized finish gives these fittings fair corrosion resistance. They have the strength to handle medium-pressure applications.

Crimp these fittings onto steel pipe to form a tightly sealed connection that’s faster than threading or welding and doesn’t require heat.

Also known as no-hub pipe fittings and soil pipe fittings, these fittings are for use in gravity-flow applications both above and below ground.

The male threads on these brass fittings have a sealant applied for extra protection against leaks. Also known as Pressure Class 125 fittings, they are built for use in low-pressure applications.

These brass fittings have the strength to handle high-pressure applications.

When space in your pipe line is limited, choose these miniature fittings that are one inch or less in length.

Choose these fittings when you need better strength than our low-pressure brass and bronze pipe fittings.

Also known as Pressure Class 125 flanges, these are for use in low-pressure applications. Flanges are aluminum, which is lightweight with good corrosion resistance.

Also known as Pressure Class 3000 fittings, these have the highest pressure rating of all the aluminum pipe fittings we offer.

Connect these fittings to thick-wall plastic pipe—they have thicker, stronger walls than standard-wall fittings, so they can handle heavy duty industrial plumbing and water supply applications, such as water processing, waste water treatment, and irrigation. They can withstand pressures up to 900 psi.

Connect to CPVC pipe for use in high-temperature plumbing and water supply applications up to 200° F.

Extreme temperatures are no problem for these fittings—they’re made of PTFE, so they can withstand a wider temperature range than any of our other plastic pipe fittings for chemicals. They are commonly used in high-purity chemical flow processes, such as semiconductor and clean room applications.

These PVDF fittings meet UL 94 V-0 for flame retardance, so they delay the spread of flames to valuable equipment. PVDF is comparable to Kynar, and has the chemical resistance to stand up to solvents and other harsh substances.

Made of corrosion-resistant plastic, these fittings won’t deteriorate when used in oil applications. They have high strength and impact resistance.

These manifolds have two separate sections inside, so you can run two different substances through them without worrying about them intermixing. Also known as headers.

Unlike other manifolds, which have an inlet on either end, these have one inlet on the opposite side from the outlets. This design allows air or fluid to follow a straight path, improving flow through your system. Also known as headers.

When you’re short on vertical space, these manifolds are a good fit—they have outlets on the side instead of on top, so they have a lower profile than rectangular manifolds. Use them to distribute air or fluid to five locations from a single supply source.

With outlets on the side instead of on top, these manifolds have a lower profile than rectangular manifolds and fit well in cramped spaces. Use them to distribute air or fluid to three locations from a single supply source.

Connect these fittings to fire hydrants and washdown equipment.

The pin lugs on these fittings allow for easy gripping, so you can quickly connect to fire hydrants and washdown equipment.

The through hole allows you to connect float rods to float valves.

Join two female-threaded parts of various thread types and sizes, while allowing air, liquids, wire, or other thin materials to pass through.

Inserts come with a through-hole tap and installation tool.