Made of 18-8 stainless steel, these inserts have better corrosion resistance than black-phosphate steel.

These inserts are the most corrosion-resistant thread-locking inserts we offer.

Adhesive on both the internal and external threads keeps these inserts in place and holds screws tight.

A black-phosphate finish provides mild corrosion resistance.

These inserts are made to stringent military specifications.

With a distorted internal thread and keys on the outside, these inserts create a strong hold on both fasteners and surrounding material.

Inserts come with a through-hole tap and installation tool.

Made of Nitronic 60 stainless steel, these inserts prevent the screw from binding or sticking without any coating or lubricant that could contaminate particle-free environments.

Made of Nitronic 60 stainless steel, these inserts prevent the screw from binding or sticking without any coating or lubricant that could contaminate particle-free environments.

Made of nickel alloy, these inserts are more resistant to acids and salt water than stainless steel inserts.

Assortments include various sizes of helical inserts and a tap, a drill bit, and an installation tool for each thread size.

A dry film keeps the screw from sticking or binding in these inserts during installation.

The tapered shape makes it easier to guide these inserts into a hole during installation. Use a drill bit to create a straight hole, then taper the top half.

Install these inserts into plastic parts to create a secure base for fasteners.

These 18-8 stainless steel inserts have better corrosion resistance than aluminum inserts and may be mildly magnetic.

These 18-8 stainless steel inserts have better corrosion resistance than brass inserts and may be mildly magnetic.

These aluminum inserts are 70% lighter than brass inserts, electrically conductive, and nonmagnetic. They have good corrosion resistance, which is comparable to brass but not as good as stainless steel.

These 18-8 stainless steel inserts have better corrosion resistance than brass inserts and may be mildly magnetic.

The flange keeps these inserts from pulling through a hole. Press them in from the underside of material, and install a screw from the top of material.

Push down on the inside of these inserts with an installation tool and they expand to hold firm in surrounding material.

Made from brass, these inserts are nonmagnetic, mildly corrosion resistant, and electrically conductive.

Assortments include various sizes of tapping inserts for hardwood.

The flange keeps these inserts from being pulled through a hole and provides a load bearing surface.

These 18-8 stainless steel tee nut inserts have better corrosion resistance than zinc-plated steel tee nut inserts.

Steel inserts have high strength for durability.

Fewer prongs than other tee nut inserts reduce the risk of splitting hardwood—these inserts have three short prongs.

Hooked prongs give these inserts excellent holding power even when removing screws.

A closed end seals out elements and protects the threads on these inserts from debris.

Mount these inserts flush or below the material's surface.

A wide flange distributes the load over a large area. Hammer these inserts into a drilled hole.

The most corrosion resistant twist-resistant rivet nuts we offer, these stand up to chemicals.

These aluminum rivet nuts are one-third the weight of steel rivet nuts and have mild corrosion resistance.

Wedges under the flange lock the nut in place in soft materials such as brass and aluminum.

These rivet nuts are mildly corrosion resistant.

About twice as strong as aluminum rivet nuts, these low-profile rivet nuts have a cadmium or tin-zinc plating for corrosion resistance.

The most corrosion resistant low-profile rivet nuts we offer, these stand up to chemicals.

These low-profile rivet nuts are one-third the weight of steel and have mild corrosion resistance.

About twice as strong as aluminum rivet nuts, these rivet nuts are zinc plated for mild corrosion resistance.

Threads float inside the nut so you can install a screw at a slight angle to align with off-center parts. They’re also known as Riv-Float nuts.