To gradually relieve pressure in lines for diesel fuel, fuel oil, gasoline, and kerosene, these valves begin opening at the set pressure and fully open at about 10% over the set pressure.

These valves have union fittings that disassemble for fast installation and removal from pipelines. Use with water, air, and inert gas.

Attach gauges or sensors to these valves so you can remove them for maintenance and calibration without depressurizing your line. They are also known as block and bleed valves.

For fast installation and removal from pipelines, these valves have union fittings that disassemble into multiple pieces. All have a fluoroelastomer seal and a plastic body that can stand up to aggressive and corrosive solutions in chemical-processing applications.

Union fittings on both ends of these valves disassemble for fast installation and removal from your pipeline. Insert unthreaded pipe into the socket ends and bond with primer and cement to create a permanent, leak-tight connection. These valves have a fluoroelastomer seal and a plastic body that can withstand aggressive and corrosive solutions in chemical-processing applications.

Insert tubing into the fittings on these valves—no heat, solder, or flux required. To withstand aggressive and corrosive solutions, they have a chemical-resistant fluoroelastomer seal and a plastic body.

For extra gripping power and a strong seal, these valves have Yor-Lok fittings with two sleeves that bite into tubing as you tighten the nut. They are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings. All have a PTFE seal and a corrosion-resistant 316 stainless steel body that can stand up to aggressive and corrosive solutions in chemical-processing applications.

A low-profile handle allows these valves to fit in low-clearance pipelines for diesel fuel, fuel oil, gasoline, and kerosene.

For use with threaded pipe, these valves have NPT connections.

With a plastic body and a fluoroelastomer seal, these valves can stand up to aggressive and corrosive solutions in chemical-processing applications.

Limit wear and damage in high-cycling applications—these valves have additional seals that prevent leakage to reduce maintenance time.

With a ball-valve design, these valves can handle three times the flow of butterfly valves.

Also known as diaphragm valves, these have a diaphragm that can handle dirty liquid, slurries, and abrasive media without damage.

For three times the flow of butterfly valves, these have a ball valve design.

All valves have threaded NPT connections.

Use these valves with NPT threaded pipe. They have a fluoroelastomer seal and a plastic body to withstand aggressive and corrosive solutions in chemical-processing applications. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

For extra gripping power and a strong seal, these valves have Yor-Lok fittings with two sleeves that bite into tubing as you tighten the nut. All are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings. The 316 stainless steel body and seal, the PTFE seat and packing, and the Monel needle can withstand aggressive and corrosive solutions in chemical-processing applications. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Valves have NPT connections for use with threaded pipe. Turn the handle to adjust the flow of butane, diesel fuel, fuel oil, gasoline, kerosene, natural gas, and propane in small increments.

To automatically shut off the flow of diesel fuel, fuel oil, kerosene, and oil in case of fire, these valves automatically close and the handle permanently fuses in place when the ambient temperature reaches 165° F.

Install these valves between ANSI flanges.

The most chemical-resistant check valves in our offering, these have a PFA body to withstand methyl ethyl ketone, sodium hypochlorite, and other extremely harsh chemicals.

Barbs grip onto tubing, providing a secure hold.

Insert tubing into the fittings on these valves—no heat, solder, or flux required. All are for use with water, oil, air, and inert gas. They divert flow between ports in tubing lines.

There’s no need to unbolt these valves for cleaning—remove the handle and slide the valve apart for inline access to internal components. Also known as elliptical valves, they have a fluoroelastomer seal and a polypropylene body for diverting flow in chemical-processing applications.