Shape Shape | Show |
|---|
|
Heat-Shrink Tubing Type Heat-Shrink Tubing Type |
|---|
 | Tapered Tubing |
System of Measurement System of Measurement |
|---|
|
Color Color |
|---|
 | Black |
Minimum ID After Shrinking Minimum ID After Shrinking |
|---|
|
|
Component Component |
|---|
|
Liner Material Liner Material |
|---|
|
Flexibility Flexibility |
|---|
 | Flexible |
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement)  |
|---|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
|---|
|
End Shape End Shape |
|---|
|
Clarity Clarity |
|---|
 | Opaque |
End Style End Style |
|---|
|
Performance Properties Performance Properties |
|---|
|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
|---|
|
Finish Finish |
|---|
|
Minimum Temperature Minimum Temperature |
|---|
|
About Duct Connections
More
About Heat-Shrink Tubing
More
Tapered Heat-Shrink Tubing
 Style D (After Shrinking) |  Style D and E (Before Shrinking) |
 Style E (After Shrinking) |
- Material: Polyolefin Plastic
- Shrink Ratio: See Table
- Dielectric Strength: 200 V/mil
- Shrink Temperature: 250° F
- Temperature Range: -65° to 275° F
A different shrink ratio on each end allows this tubing to fit over cable assemblies and wire harnesses with large connections, or around connectors with a 90° elbow. An adhesive lining melts when the tubing is heated and bonds to the underlying surface, creating a water-resistant seal. The tubing length listed is after shrinking; the length before shrinking is 20-25% shorter.
Lipped tubing has a ridge on the inside of one opening for better retention than non-lipped tubing. It’s often used with grooved adapters—upon shrinking, the lip grips onto the groove.
Dielectric strength is the maximum voltage a material can handle before it starts to breakdown.
Tapered End | Non-Tapered End | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Style | ID Before Shrinking | Min. ID After Shrinking | Shrink Ratio | ID Before Shrinking | Min. ID After Shrinking | Shrink Ratio | Min. Wall Thick. After Shrinking | Color | End Style | Lg. | Each | |
| D | 1.25" | 0.28" | 4.5:1 | 1.25" | 0.75" | 1.7:1 | 0.09" | Black | Lipped | 1.4" | 0000000 | 000000 |
| D | 1.25" | 0.28" | 4.5:1 | 1.25" | 0.75" | 1.7:1 | 0.09" | Black | Non Lipped | 1.4" | 0000000 | 00000 |
| D | 1.5" | 0.33" | 4.5:1 | 1.5" | 0.75" | 2:1 | 0.1" | Black | Lipped | 1.7" | 0000000 | 00000 |
| D | 1.5" | 0.33" | 4.5:1 | 1.5" | 0.75" | 2:1 | 0.1" | Black | Non Lipped | 1.7" | 0000000 | 00000 |
| D | 1.75" | 0.38" | 4.6:1 | 1.75" | 1.1" | 1.6:1 | 0.13" | Black | Lipped | 2.1" | 0000000 | 00000 |
| D | 1.75" | 0.38" | 4.6:1 | 1.75" | 1.1" | 1.6:1 | 0.13" | Black | Non Lipped | 2.1" | 0000000 | 00000 |
| D | 2" | 0.62" | 3.2:1 | 2" | 1.6" | 1.3:1 | 0.13" | Black | Non Lipped | 3" | 0000000 | 00000 |
| E | 3" | 0.86" | 3.5:1 | 3" | 1.41" | 2.1:1 | 0.18" | Black | Non Lipped | 5" | 0000000 | 000000 |
Standard Duct and Fittings
No need for clamps or connectors—duct and fittings press-fit together. Male ends are crimped or tapered, making them slightly smaller than a female end for simple assembly.
Galvanized steel has good corrosion resistance.
For technical drawings and 3-D models, click on a part number.
