About Tool Steel
More
Tight-Tolerance Multipurpose Oil-Hardening O1 Tool Steel Rods
- Yield Strength: 50,000 psi
- Hardness: Rockwell B90 (Medium)
- Heat Treatable: Yes
- Max. Hardness After Heat Treatment:
Inch sizes: Rockwell C65
Metric sizes: Rockwell C62 - Specifications Met: ASTM A681
Ready for turning in a lathe, these rods are precision ground to a tight diameter tolerance. They’re also known as drill rod. Often used for dies, punches, and gauges, O1 tool steel is an oil-hardening material that resists wear and abrasion.
For technical drawings and 3-D models, click on a part number.
Certificates with a traceable lot number are available for these products. Download certificates from ORDER HISTORY after your order ships.
Tight-Tolerance Easy-to-Machine W1 Tool Steel Rods
- Yield Strength: 50,000 psi
- Hardness: Rockwell B95 (Medium)
- Heat Treatable: Yes
- Max. Hardness After Heat Treatment: Rockwell C65
- Specifications Met: ASTM A686
These rods, also called drill rod, are ground and held to strict diameter and straightness tolerances. They are ready to be turned in a lathe. With lower amounts of alloy elements than other tool steels, W1 offers excellent machinability. This water-hardening material is often used for hammers, files, taps, and reamers. These rods are decarb-free for a uniform surface that will consistently accept heat treating.
For technical drawings and 3-D models, click on a part number.
Certificates with a traceable lot number are available for these products. Download certificates from ORDER HISTORY after your order ships.
Full-Groove Dowel Pins
Grooves run the full length of these pins for a firm hold that won't spin. Use them in place of standard dowel, spring, and taper pins to fasten parts. The three grooves pinch shut when pressed into a hole, creating tension to lock pins in place. For the best fit, the hole should be equal to or slightly larger than the diameter shown. The ends are chamfered for easy insertion. Breaking strength is measured as double shear, which is the force required to break a pin into three pieces. Also known as type A pins.
Pins with tapered grooves are easier to install than pins with parallel grooves, but more likely to loosen from vibration. Zinc-plated steel pins have good strength and some corrosion resistance.
18-8 stainless steel pins offer a balance of strength and corrosion resistance. They may be mildly magnetic. Pins are passivated for added protection against corrosion and oxidation.
For technical drawings and 3-D models, click on a part number.
Lg. | Dia. (A) | Dia. (A) Tolerance | Dia. (B) | Dia. (B) Tolerance | Breaking Strength, lbs. | Groove Style | Pkg. Qty. | Pkg. | |
3/16" Dia. | |||||||||
---|---|---|---|---|---|---|---|---|---|
1 1/2" | 0.188" | -0.002" to 0" | 0.197" | -0.003" to 0.003" | 3,300 | Tapered | 10 | 000000000 | 000000 |
Lg. | Dia. (A) | Dia. (A) Tolerance | Dia. (B) | Dia. (B) Tolerance | Breaking Strength | Groove Style | Pkg. Qty. | Pkg. | |
3/16" Dia. | |||||||||
---|---|---|---|---|---|---|---|---|---|
1 1/2" | 0.188" | -0.002" to 0" | 0.197" | -0.003" to 0.003" | Not Rated | Tapered | 5 | 000000000 | 00000 |
Center-Groove Dowel Pins
Center-groove pins are often used in place of clevis pins or to create T-handles. The grooves pinch shut when pressed into a hole, creating tension and holding the pin in place. The grooved center locks pins in position, while the smooth ends act as a pivot. For the best fit, the hole should be equal to or slightly larger than the diameter shown. The ends are chamfered for easy insertion. Pins are made of zinc-plated steel for good strength and some corrosion resistance. Breaking strength is measured as double shear, which is the force required to break a pin into three pieces. Also known as type E pins.
For technical drawings and 3-D models, click on a part number.
Lg. | Dia. (A) | Dia. (A) Tolerance | Dia. (B) | Dia. (B) Tolerance | Groove Lg. | Breaking Strength, lbs. | Pkg. Qty. | Pkg. | |
Zinc-Plated 1117 Carbon Steel, Zinc-Plated 1215 Carbon Steel | |||||||||
---|---|---|---|---|---|---|---|---|---|
3/16" Dia. | |||||||||
1 1/2" | 0.188" | -0.002" to 0" | 0.197" | -0.003" to 0.003" | 3/4" | 3,300 | 10 | 000000000 | 000000 |
Half-Groove Dowel Pins
These pins make good hinges or pivots. The grooves pinch shut when pressed into a hole, creating tension and holding the pin in place. The grooved half locks pins in position, while the smooth half acts as a pivot. For the best fit, the hole should be equal to or slightly larger than the diameter shown. The ends are chamfered for easy insertion. Pins are made of zinc-plated steel for good strength and some corrosion resistance. Breaking strength is measured as double shear, which is the force required to break a pin into three pieces. Also known as type H pins.
For technical drawings and 3-D models, click on a part number.
Lg. | Dia. (A) | Dia. (A) Tolerance | Dia. (B) | Dia. (B) Tolerance | Groove Lg. | Breaking Strength, lbs. | Pkg. Qty. | Pkg. | |
Dowel Pins—Zinc-Plated12L14 Carbon Steel | |||||||||
---|---|---|---|---|---|---|---|---|---|
3/16" Dia. | |||||||||
1 1/2" | 0.188" | -0.002" to 0" | 0.197" | -0.003" to 0.003" | 3/4" | 3,300 | 10 | 000000000 | 000000 |
Half-Groove Dowel Pins with Notch
These pins are commonly used as anchors for tension springs. The grooved half locks pins in position, and spring ends fit in to the notch. The grooves pinch shut when pressed into a hole, creating tension and holding the pin in place. For the best fit, the hole should be equal to or slightly larger than the diameter shown. The ends are rounded for easy insertion. Pins are made of zinc-plated steel for good strength and some corrosion resistance. Breaking strength is measured as double shear, which is the force required to break a pin into three pieces. Also known as type G pins.
For technical drawings and 3-D models, click on a part number.
Lg. | Dia. (A) | Dia. (A) Tolerance | Dia. (B) | Dia. (B) Tolerance | Groove Lg. | Breaking Strength, lbs. | Pkg. Qty. | Pkg. | |
Zinc-Plated 12L14 Carbon Steel | |||||||||
---|---|---|---|---|---|---|---|---|---|
3/16" Dia. | |||||||||
1 1/2" | 0.188" | -0.002" to 0" | 0.197" | -0.003" to 0.003" | 3/4" | 3,300 | 10 | 000000000 | 000000 |
Quarter-Groove Dowel Pins
Quarter-groove pins are well suited for hinges or pivots. The grooves pinch shut when pressed into a hole, creating tension and holding the pin in place. The grooved end locks pins in position, while the smooth portion acts as a pivot. For the best fit, the hole should be equal to or slightly larger than the diameter shown. The ends are chamfered for easy insertion. Pins are made of zinc-plated steel for good strength and some corrosion resistance. Breaking strength is measured as double shear, which is the force required to break a pin into three pieces. Also known as type C pins.
For technical drawings and 3-D models, click on a part number.
Lg. | Dia. (A) | Dia. (A) Tolerance | Dia. (B) | Dia. (B) Tolerance | Groove Lg. | Breaking Strength, lbs. | Pkg. Qty. | Pkg. | |
Zinc-Plated 12L14 Carbon Steel | |||||||||
---|---|---|---|---|---|---|---|---|---|
3/16" Dia. | |||||||||
1 1/2" | 0.188" | -0.002" to 0" | 0.197" | -0.003" to 0.003" | 3/8" | 3,300 | 10 | 000000000 | 000000 |
High-Strength Fracture- and Wear-Resistant Zirconia Ceramic Rods and Discs
Ideal for applications that must resist bending and wear as well as carry heavy loads, these rods and discs are often used for sleeve bearings and shafts instead of metal. Added yttria gives this material more strength and lowers the chances of cracking from impact compared to standard zirconia, alumina, and silicon nitride ceramic. If cracks do occur, they will not spread, extending the life and reliability of this material. It also means this zirconia blend resists wearing down from rubbing against another part or abrasion from chemical slurries.
Zirconia ceramic resists bending better than alumina and silicon nitride ceramic but does not withstand rapid temperature changes or high temperatures as well as other high-performance ceramics.
For technical drawings and 3-D models, click on a part number.