3" Rods | McMaster-Carr

Made with more carbon and manganese than other easy-to-machine carbon steels, 1144 carbon steel has a higher yield strength and hardness. Also known as Stressproof, these rods are stress-relieved to minimize warping during machining.

Tight-Tolerance High-Strength
Easy-to-Machine 1144 Carbon Steel Rods

These rods are precision ground and held to a strict straightness tolerance, so they're all set for turning applications in your lathe.

Ultra-Strength Easy-to-Machine
1144 Carbon Steel Rods

Also known as Fatigueproof, these rods have enhanced strength and resistance to breaking from repeated impact compared to High-Strength Easy-to-Machine 1144 Carbon Steel Rods.

Ultra-Machinable 12L14 Carbon Steel Rods

The lead additive acts as a lubricant, which allows 12L14 carbon steel to withstand very fast machining. It's used to fabricate a wide variety of machine parts.

Easy-to-Machine 1215 Carbon Steel Rods

A lead-free alternative to 12L14, 1215 carbon steel contains the same amount of sulfur and phosphorus for excellent machinability. It is often used for shaft couplings, studs, and pins.

High-Strength 1045 Carbon Steel Rods and Discs

Stronger than low-carbon steel with equally good machinability, 1045 carbon steel is widely used for bolts, studs, and shafts.

High-Strength 1141 Carbon Steel

Choose 1141 carbon steel for its balance of strength and machinability. Often compared to low-carbon steel, 1141 is higher strength. It’s not as machinable as similar alloys, like 1144, due to its low sulfur content.

Alloy Steel

Chrome-Plated Hardened
Multipurpose 4140 Alloy Steel Rods

A chrome plating on these rods increases their corrosion resistance. They're also hardened, which makes them more resistant to impacts and abrasion.

Hardened Multipurpose 4140 Alloy Steel Rods

These rods are hardened for increased abrasion and impact resistance. Also known as chrome-moly steel, 4140 alloy steel resists fracturing from repeated stress.

Tight-Tolerance Multipurpose 4140 Alloy Steel Rods

Ready for turning in your lathe, these rods are precision ground and held to a strict straightness tolerance.

Multipurpose 4140 Alloy Steel Rods and Discs

Also known as chrome-moly steel, this versatile 4140 alloy steel is used for a wide range of parts, such as gears, axles, shafts, collets, and die holders. It resists fracturing from repeated stress.

Easy-to-Weld 4130 Alloy Steel Rods

4130 alloy steel has a low carbon content that provides good weldability. It's often used for gears, fasteners, and structural applications.

High-Strength 4340 Alloy Steel Rods

Use for power transmission and structural applications that involve extreme impact, heat, and wear.

Hard Wear-Resistant 52100 Alloy Steel Rods

Also known as chrome steel, 52100 is an extremely hard and wear-resistant material. It’s used for parts such as bearings, bushings, and punches.

Ultra-Wear-Resistant 4150 Alloy Steel

Higher levels of carbon and chromium make this 4150 alloy steel more wear-resistant than 4820 alloy steel. Also known as chrome-moly steel, it’s often used for gears, shafts, and ball screws.

Cast Iron

Oversized Easy-to-Machine
Gray Cast Iron Rods and Discs

An oversized diameter allows for finishing to your exact requirements.

Impact-Resistant Ductile Cast Iron Rods and Discs

Ductile cast iron is strong, resilient, and able to handle repeated stress without breaking.

Easy-to-Machine Impact-Resistant
Ductile Cast Iron Rods

With a high amount of ferrite, these cast iron rods are easier to machine without cracking than other impact-resistant ductile cast iron rods. Use them to create bushings, gears, pulleys, and pistons.

Tool Steel

Oversized High-Speed M2 Tool Steel Rods

An oversized diameter allows for finishing to your exact requirements.

Tight-Tolerance Multipurpose
Air-Hardening A2 Tool Steel Rods

Precision ground and held to a strict straightness tolerance, these rods are ready for turning in your lathe.

Oversized Multipurpose Air-Hardening
A2 Tool Steel Rods and Discs

An oversized diameter allows for finishing to your exact requirements.

Oversized Wear-Resistant D2
Tool Steel Rods and Discs

An oversized diameter allows for finishing to your exact requirements.

Oversized Shock-Resistant
S7 Tool Steel Rods and Discs

An oversized diameter allows for finishing to your exact requirements.

Oversized Multipurpose Oil-Hardening
O1 Tool Steel Rods and Discs

An oversized diameter allows for finishing to your exact requirements.

Oversized High-Temperature H13 Tool Steel Rods

An oversized diameter on these rods allows for finishing to your exact requirements.

Hardened Easy-to-Machine P20 Tool Steel

Furnished hardened, P20 tool steel is strong and easy to machine. It has the wear resistance and highly polishable surface needed to fabricate long-lasting molds and dies.

Stainless Steel

Multipurpose 304 Stainless Steel

From cookware to chemical-processing equipment, 304 stainless steel is a good all-around choice for a wide range of applications.

Tight-Tolerance Multipurpose 304 Stainless Steel

This material has tighter tolerances than standard 304 stainless steel.

Easy-to-Machine 303 Stainless Steel

Widely used for fabricating fittings and fasteners, 303 stainless steel machines quickly without sticking to cutting tools.

Shaft-Quality Nitronic 60 Stainless Steel

Offering outstanding resistance to surface wear and corrosion, Nitronic 60 stainless steel is often used for shafts, fasteners, and valves.

Corrosion-Resistant 316 Stainless Steel

The addition of molybdenum gives 316 stainless steel excellent corrosion resistance. Use it in a variety of marine and chemical-processing applications.

Tight-Tolerance Corrosion-Resistant
316 Stainless Steel

This material is precision ground to offer tighter tolerances than standard 316 stainless steel.

Stress-Corrosion-Resistant 2205 Stainless Steel

2205 stainless steel resists cracking even when faced with a combination of tensile stress, corrosive chemicals, and heat. Also known as duplex stainless steel, it has twice the strength of 316 stainless steel. Use it for high-pressure applications in caustic environments.

High-Strength 17-4 PH Stainless Steel

With a higher chromium content than 15-5 PH stainless steel, this high-strength 17-4 PH offers better corrosion resistance. It is also known as 630 stainless steel.

Hardened High-Strength 17-4 PH Stainless Steel

This material is hardened for improved strength and wear resistance.

Easy-to-Machine 416 Stainless Steel

One of the most machinable types of stainless steel available, 416 contains sulfur for fast machining without clogging cutting tools. It's used for gears, screws, and shafts.

Bearing-Quality 440C Stainless Steel

One of the hardest types of stainless steel after heat treating, 440C offers excellent wear and abrasion resistance. It's often used for bearings, valves, and knife blades.

Wear-Resistant 410 Stainless Steel

Often used for fasteners and valves, 410 stainless steel withstands wear caused by abrasion.

Weldable 321 Stainless Steel

The titanium content of 321 stainless steel preserves corrosion resistance around weld points.

Aluminum

Multipurpose 6061 Aluminum Rods and Discs

The most widely used aluminum, 6061 is fabricated into everything from pipe fittings and containers to automotive and aerospace parts. It is strong and corrosion resistant, plus it's easy to machine and weld.

Tight-Tolerance Multipurpose
6061 Aluminum Rods and Discs

These rods and discs are precision ground to offer tighter tolerances than standard 6061 rods and discs.

Anodized Multipurpose 6061 Aluminum Rods

An anodized coating forms a bond with the aluminum surface to improve wear and corrosion resistance.

High-Strength 7075 Aluminum Rods and Discs

Originally developed for aircraft frames, uses for 7075 aluminum now include keys, gears, and other high-stress parts. It is often used as a replacement for 2024 aluminum because it’s stronger and provides similar performance in all other aspects.

High-Strength 2024 Aluminum Rods and Discs

While 2024 aluminum was initially designed for structural components in aircraft, it's now widely used when a high strength-to-weight ratio is needed, such as for gears, shafts, and fasteners. It offers similar performance to 7075 aluminum, but it’s not as strong.

Easy-to-Machine 2011 Aluminum Rods

2011 has the best machinability of all the aluminum alloys. It is the most selected aluminum for screws, tube fittings, hose parts, and other items that require extensive machining.

Copper, Brass, and Bronze

Ultra-Machinable 360 Brass Rods and Discs

With the highest lead content of all the brass alloys, 360 offers the best machinability. Often called free-machining and free-cutting brass, it stands up to high-speed drilling, milling, and tapping operations with minimal wear on your tools. It’s commonly used for gears, pinions, and lock components.

Marine-Grade 485 Brass

Also known as high-leaded naval brass, 485 brass contains lead for good machinability. It is commonly used for marine hardware, valve stems, and screw machine products.

Multipurpose 110 Copper Rods and Discs

Offering high electrical conductivity and formability, 110 copper is 99.9% pure. Also known as ETP copper, it's often used in electrical applications, such as for bus bars and wire connectors, as well as for flashing, gaskets, and rivets.

Super-Conductive 101 Copper Rods and Discs

With 99.99% copper content, 101 copper has higher purity than 110 copper, resulting in superior electrical conductivity. It's commonly called OFE and OFHC copper. Use it in electrical applications, such as for coaxial cables and terminal lugs.

Extra High-Strength
Beryllium-Free 180 Copper Rods

Even though they have similar performance properties to beryllium copper, these copper rods don't require special machining techniques.

Oversized 932 Bearing Bronze Rods

Diameter is oversized to allow for finishing.

Tight-Tolerance 932 Bearing Bronze Rods

These rods are precision ground for a tight diameter tolerance of ±0.0005".

Weldable 954 Bearing Bronze Rods

954 bronze contains a minimum of 10% aluminum for strength and weldability. It is also known as aluminum bronze. It's widely used for bearings, bushings, valve bodies, and worm gears.

Oil-Filled 841 Bearing Bronze Rods

Powdered bronze is pressed and then impregnated with SAE 30 oil to make this material self-lubricating.

Easy-to-Machine 936 Bearing Bronze Rods

An easier-to-machine alternative to 932 bronze, 936 also has better corrosion resistance. It's also called modified SAE 64.

Ultra-Wear-Resistant AMPCO® 18 Bearing Bronze

AMPCO® 18 is a premium aluminum-bronze alloy that combines strength with superior wear resistance.

High-Strength Machinable 955 Bronze

For a good combination of strength, machinability, and weldability, choose 955 bronze.

Nickel

High-Strength 625 Nickel Rods

A blend of nickel, chromium, and molybdenum gives these 625 nickel rods the strength, weldability, and corrosion resistance necessary for use in expansion joints, exhaust systems, and marine components. They are comparable to Inconel 625 and Haynes 625.

Ultra-Strength 718 Nickel Rods

Often used for cryogenic tanks and fasteners, these 718 nickel rods will maintain their high strength in temperatures from -300° to 1200° F, even after long-term exposure. They are comparable to Inconel 718.

Zinc Rods

Cut and thread discs and other parts that draw corrosion away from nearby metal in water tanks, heat exchangers, and marine applications.

Multipurpose Plastic

Wear-Resistant Easy-to-Machine
Delrin® Acetal Resin Rods and Discs

Delrin® acetal resin, also known as acetal homopolymer, is stronger and stiffer than acetal copolymer.

Slippery Wear-Resistant Easy-to-Machine
Delrin® Acetal AF Resin Rods and Discs

The addition of PTFE provides a more slippery, wear-resistant surface than standard Delrin® acetal resin. It’s commonly fabricated into pump components, gears, and bearings.

Wear-Resistant Easy-to-Machine
Acetal Rods and Discs

An economical alternative to Delrin® acetal resin, this acetal copolymer offers similar wear resistance.

Slippery Wear-Resistant
Easy-to-Machine Acetal Copolymer

A silicone additive gives this material a self-lubricating surface that reduces friction and extends the life of your parts.

Wear-Resistant Nylon Rods and Discs

Also known as nylon 6/6, this general purpose material is often used for bearings, gears, valve seats, and other high-wear parts.

Moisture- and Wear-Resistant Nylon Rods

Because this 6/12 material absorbs less water than standard nylon 6/6, it holds its shape better. It’s often machined into hose fittings and valve components.

MDS-Filled Easy-to-Machine
Wear-Resistant Cast Nylon Rods and Discs

The addition of MDS results in a nylon with exceptional wear resistance as well as self-lubricating properties.

Oil-Filled Easy-to-Machine
Wear-Resistant Cast Nylon Rods

This nylon stays lubricated over time because it’s filled with oil. Use it to fabricate parts for hard-to-reach places where adding lubricants would be difficult.

Heat-Stabilized Easy-to-Machine
Wear-Resistant Cast Nylon Rods

Use these cast nylon 6 rods to make sheaves, bushings, and pulleys. All withstand higher temperatures and are easier to machine than standard nylon 6/6 rods.

Easy-to-Machine Wear-Resistant
Cast Nylon Rods and Discs

This cast nylon 6 material is easier to machine than other types of nylon. It’s comparable to Nylatron and Nycast.

Slippery UHMW Polyethylene Rods and Discs

In addition to a low-friction surface that prevents sticking and binding, this tough material is impact and wear resistant to handle the scuffs, scrapes, and strikes that other plastics can’t.

Antistatic Slippery UHMW Polyethylene Rods

This material suppresses static charges to prevent dust from building up.

Oil-Filled Slippery UHMW Polyethylene Rods

This oil-filled material is self-lubricating for an extra-slippery surface.

Metal-Detector-Grade Slippery
UHMW Polyethylene Rods

If a chip of this material breaks off, it can be located by metal detectors to reduce contamination risks.

Chemical-Resistant PVC Rods and Discs

Because PVC resists many acids and alkalies, it’s widely used for tanks and in chemical-processing applications. Also known as PVC Type 1.

High-Temperature CPVC Rods

CPVC is just as chemical resistant as standard PVC Type 1 and can handle hotter temperatures up to 200° F.

Impact- and Chemical-Resistant PVC Rods

Offering greater impact resistance than standard PVC Type 1 with similar chemical resistance, this PVC Type 2 is widely used for parts that are subject to shock.

Impact-Resistant Easy-to-Form ABS Rods

Because ABS maintains its toughness even after thermoforming, it’s often made into storage cases, tote trays, equipment housings, and protective gear.

Moisture-Resistant Polyethylene
(HDPE) Rods and Discs

Practically nonabsorbent, HDPE won't swell when exposed to moisture. It is denser and more rigid than LDPE, plus it's more chemical resistant.

Polypropylene Rods

Because this polypropylene resists swelling when exposed to water, it’s often fabricated into containers and parts for laboratory equipment.

Slippery Moisture-Resistant Polyester

When moisture-resistant polyester is combined with PTFE, the result is this self-lubricating material. It’s also called Hydex and PBT.

Moisture-Resistant Polyester Rods

Polyester resists swelling in wet environments.

Impact-Resistant Polycarbonate Rods

Polycarbonate maintains good impact resistance across a wide temperature range. It's comparable to Lexan, Hyzod, Tuffak, and Makrolon.

High-Strength Glass-Filled
Impact-Resistant Polycarbonate Rods

The addition of glass fibers to this polycarbonate increases tensile strength for use in structural applications.

Flexible Polyethylene (LDPE) Rods

One of the softest and most flexible plastics we offer, LDPE is more formable than HDPE.

High-Temperature Plastic

Chemical-Resistant Slippery PTFE Rods and Discs

Known for its naturally slippery surface, PTFE surpasses most plastics when it comes to chemical resistance and performance in extreme temperatures.

Recycled PTFE

Also called reprocessed and mechanical-grade PTFE, this material is an economical alternative to standard PTFE.

Durable Glass-Filled
Chemical-Resistant Slippery PTFE Rods

This glass-filled PTFE is more rigid than standard PTFE for increased durability in high-stress applications.

Wear- and Chemical-Resistant
PEEK Rods and Discs

Not only does PEEK provide superior wear resistance in repetitive processes, it is also resists wear caused by abrasion. PEEK can be used as a lightweight substitute for metal parts in chemical-processing applications.

Electrical-Insulating Ultem PEI Rods

Often used for circuit-breaker housings, manifolds, and semiconductor components, Ultem PEI offers excellent electrical-insulating properties.

Clear Plastic

Clear Scratch- and UV-Resistant
Acrylic Rods and Discs

This extruded acrylic offers similar performance as cast acrylic at a lower cost.

Clear Scratch- and UV-Resistant
Cast Acrylic Rods and Discs

Cast acrylic is easier to machine than extruded acrylic. It's comparable to Lucite and Plexiglas® Acrylic.

Clear Impact-Resistant
Polycarbonate Rods and Discs

At only half the weight of glass, polycarbonate maintains excellent impact resistance across a wide temperature range. It's comparable to Lexan, Hyzod, Tuffak, and Makrolon.

Mirrored Scratch-Resistant Acrylic Discs

Resistant to scratches and scuffs, mirrored acrylic is an economical alternative to mirrored polycarbonate.

Power Transmission

Acme Lead Screws and Nuts

Found in hand-powered clamps, vises, grates, doors, and work tables, lead screws and nuts have broad, square threads that are well suited for quick assembly, high clamping forces, and lifting and lowering heavy objects.

Keyed Rotary Shafts

Combine with a machine key to transmit torque to gears, sprockets, and other power transmission components.

Garolite

Multipurpose Flame-Retardant
Garolite G-10/FR4 Rods

A good all-around choice, Garolite G-10/FR4 is strong, machinable, and electrically insulating. It meets UL 94 V-0 for flame retardance.

Multipurpose Flame-Retardant
Garolite G-10/FR4 Discs

A good all-around choice, Garolite G-10/FR4 is strong, machinable, and electrically insulating. It meets UL 94 V-0 for flame retardance.

Easy-to-Machine Garolite LE Rods

Using nothing more than standard high-speed steel tooling, Garolite LE can be machined into intricate parts.

Economical Garolite CE Rods

Garolite CE is often fabricated into parts where high strength is not required.

Glass, Mica, Ceramic, and Graphite

Easy-to-Machine Alumina-Bisque
Ceramic Rods and Discs

Often used to create prototype components, these ceramic rods and discs come semi-fired so they can be machined using conventional metalworking tools.

Low Thermal Expansion
Alumina-Silicate Ceramic Rods

Conductive Graphite Rods

Ultra-High-Temperature
Quartz Glass Rods and Discs

Able to withstand temperatures up to 2100° F, this quartz glass is useful in high-temperature applications that also require optical clarity, such as high-intensity lighting, fiber-optic production, and optical lens systems.

Borosilicate Glass Rods and Discs

Also called Pyrex and Schott glass, these glass rods and discs resist clouding and pitting and are highly chemical and heat resistant.

Rubber

Abrasion-Resistant Polyurethane Rubber Rods

Stronger than natural rubber, these polyurethane rods combine the shock-absorbing qualities of rubber with the tear resistance of plastic. Use them to seal narrow spaces such as channels.

Multipurpose Neoprene Rubber Rods

The cylindrical shape fits into channels and other narrow spaces for sealing and cushioning.

Oil-Resistant Buna-N Rubber Rods

Seal and cushion narrow spaces, such as inside channels and seams.

Backer Rods

Provide support for sealants in gaps—insert these backer rods into gaps and fill in with sealant.

Super-Cushioning Foam

Super-Cushioning Polyurethane
Foam Cords and Circles

Use these flexible polyurethane foam cords and circles to cushion narrow spaces, such as channels and gaps.

Super-Cushioning Foam Half Rounds

Use these foam half rounds as a cushioning bumper.

Carbon Steel

Low-Carbon Steel Rods and Discs

High-Strength Easy-to-Machine1144 Carbon Steel Rods

Tight-Tolerance High-StrengthEasy-to-Machine 1144 Carbon Steel Rods

Ultra-Strength Easy-to-Machine1144 Carbon Steel Rods

Ultra-Machinable 12L14 Carbon Steel Rods

Easy-to-Machine 1215 Carbon Steel Rods

High-Strength 1045 Carbon Steel Rods and Discs

High-Strength 1141 Carbon Steel

Alloy Steel

Chrome-Plated HardenedMultipurpose 4140 Alloy Steel Rods

Hardened Multipurpose 4140 Alloy Steel Rods

Tight-Tolerance Multipurpose 4140 Alloy Steel Rods

Multipurpose 4140 Alloy Steel Rods and Discs

Easy-to-Weld 4130 Alloy Steel Rods

High-Strength 4340 Alloy Steel Rods

Hard Wear-Resistant 52100 Alloy Steel Rods

Ultra-Wear-Resistant 4150 Alloy Steel

Cast Iron

Oversized Easy-to-MachineGray Cast Iron Rods and Discs

Impact-Resistant Ductile Cast Iron Rods and Discs

Easy-to-Machine Impact-ResistantDuctile Cast Iron Rods

Tool Steel

Oversized High-Speed M2 Tool Steel Rods

Tight-Tolerance MultipurposeAir-Hardening A2 Tool Steel Rods

Oversized Multipurpose Air-HardeningA2 Tool Steel Rods and Discs

Oversized Wear-Resistant D2Tool Steel Rods and Discs

Oversized Shock-ResistantS7 Tool Steel Rods and Discs

Oversized Multipurpose Oil-HardeningO1 Tool Steel Rods and Discs

Oversized High-Temperature H13 Tool Steel Rods

Hardened Easy-to-Machine P20 Tool Steel

Stainless Steel

Multipurpose 304 Stainless Steel

Tight-Tolerance Multipurpose 304 Stainless Steel

Easy-to-Machine 303 Stainless Steel

Shaft-Quality Nitronic 60 Stainless Steel

Corrosion-Resistant 316 Stainless Steel

Tight-Tolerance Corrosion-Resistant316 Stainless Steel

Stress-Corrosion-Resistant 2205 Stainless Steel

High-Strength 17-4 PH Stainless Steel

Hardened High-Strength 17-4 PH Stainless Steel

Easy-to-Machine 416 Stainless Steel

Bearing-Quality 440C Stainless Steel

Wear-Resistant 410 Stainless Steel

Weldable 321 Stainless Steel

Aluminum

Multipurpose 6061 Aluminum Rods and Discs

Tight-Tolerance Multipurpose6061 Aluminum Rods and Discs

Anodized Multipurpose 6061 Aluminum Rods

High-Strength 7075 Aluminum Rods and Discs

High-Strength 2024 Aluminum Rods and Discs

Easy-to-Machine 2011 Aluminum Rods

Copper, Brass, and Bronze

Ultra-Machinable 360 Brass Rods and Discs

Marine-Grade 485 Brass

Multipurpose 110 Copper Rods and Discs

Super-Conductive 101 Copper Rods and Discs

Extra High-StrengthBeryllium-Free 180 Copper Rods

Oversized 932 Bearing Bronze Rods

Tight-Tolerance 932 Bearing Bronze Rods

Weldable 954 Bearing Bronze Rods

Oil-Filled 841 Bearing Bronze Rods

Easy-to-Machine 936 Bearing Bronze Rods

Ultra-Wear-Resistant AMPCO® 18 Bearing Bronze

High-Strength Machinable 955 Bronze

Nickel

High-Strength 625 Nickel Rods

Ultra-Strength 718 Nickel Rods

Zinc Rods

Zinc Rods

Multipurpose Plastic

Wear-Resistant Easy-to-MachineDelrin® Acetal Resin Rods and Discs

Slippery Wear-Resistant Easy-to-MachineDelrin® Acetal AF Resin Rods and Discs

Wear-Resistant Easy-to-MachineAcetal Rods and Discs

Slippery Wear-ResistantEasy-to-Machine Acetal Copolymer

Wear-Resistant Nylon Rods and Discs

Moisture- and Wear-Resistant Nylon Rods

MDS-Filled Easy-to-MachineWear-Resistant Cast Nylon Rods and Discs

Oil-Filled Easy-to-MachineWear-Resistant Cast Nylon Rods

Heat-Stabilized Easy-to-MachineWear-Resistant Cast Nylon Rods

High-Strength Easy-to-Machine
1144 Carbon Steel Rods

Tight-Tolerance High-Strength
Easy-to-Machine 1144 Carbon Steel Rods

Ultra-Strength Easy-to-Machine
1144 Carbon Steel Rods

Chrome-Plated Hardened
Multipurpose 4140 Alloy Steel Rods

Oversized Easy-to-Machine
Gray Cast Iron Rods and Discs

Easy-to-Machine Impact-Resistant
Ductile Cast Iron Rods

Tight-Tolerance Multipurpose
Air-Hardening A2 Tool Steel Rods

Oversized Multipurpose Air-Hardening
A2 Tool Steel Rods and Discs

Oversized Wear-Resistant D2
Tool Steel Rods and Discs

Oversized Shock-Resistant
S7 Tool Steel Rods and Discs

Oversized Multipurpose Oil-Hardening
O1 Tool Steel Rods and Discs

Tight-Tolerance Corrosion-Resistant
316 Stainless Steel

Tight-Tolerance Multipurpose
6061 Aluminum Rods and Discs

Extra High-Strength
Beryllium-Free 180 Copper Rods

Wear-Resistant Easy-to-Machine
Delrin® Acetal Resin Rods and Discs

Slippery Wear-Resistant Easy-to-Machine
Delrin® Acetal AF Resin Rods and Discs

Wear-Resistant Easy-to-Machine
Acetal Rods and Discs

Slippery Wear-Resistant
Easy-to-Machine Acetal Copolymer

MDS-Filled Easy-to-Machine
Wear-Resistant Cast Nylon Rods and Discs

Oil-Filled Easy-to-Machine
Wear-Resistant Cast Nylon Rods

Heat-Stabilized Easy-to-Machine
Wear-Resistant Cast Nylon Rods

Easy-to-Machine Wear-Resistant
Cast Nylon Rods and Discs

Metal-Detector-Grade Slippery
UHMW Polyethylene Rods

Moisture-Resistant Polyethylene
(HDPE) Rods and Discs

High-Strength Glass-Filled
Impact-Resistant Polycarbonate Rods

Durable Glass-Filled
Chemical-Resistant Slippery PTFE Rods

Wear- and Chemical-Resistant
PEEK Rods and Discs

Clear Scratch- and UV-Resistant
Acrylic Rods and Discs

Clear Scratch- and UV-Resistant
Cast Acrylic Rods and Discs

Clear Impact-Resistant
Polycarbonate Rods and Discs

Multipurpose Flame-Retardant
Garolite G-10/FR4 Rods

Multipurpose Flame-Retardant
Garolite G-10/FR4 Discs

Easy-to-Machine Alumina-Bisque
Ceramic Rods and Discs

Low Thermal Expansion
Alumina-Silicate Ceramic Rods

Ultra-High-Temperature
Quartz Glass Rods and Discs

Super-Cushioning Polyurethane
Foam Cords and Circles