1/2"-20 Rods | McMaster-Carr

Filter by

System of Measurement

Thread Size

Diameter

End Type

Material

Length

Thread Length

Mechanical Finish

Thread Direction

Shaft Motion

Threading

Edge Type

Hardness Rating

Hardness

RoHS Compliance

Overall Length

DFARS Compliance

Heat Treatment

Yield Strength

(ORDERING) Length Increment

Fastener Strength Grade/Class

Maximum (ORDERING) Length

Minimum (ORDERING) Length

Forward

How can we improve?

648 Products

About Shafts

Threaded Linear Motion Shafts

Mount these externally threaded shafts into tapped holes rather than using a shaft support, or attach a hex nut, shaft collar, or other threaded accessory.

Tapped Linear Motion Shafts

Internal threads allow you to mount these shafts onto threaded studs and fasteners, no shaft supports needed.

Step-Down Linear Motion Shafts

A shoulder near the end of the shaft allows for easy positioning of housings, shaft supports, and collars.

Linear Motion Shafts with Retaining Ring Grooves

Clip retaining rings into the grooves to separate and position collars, supports, and housings.

Rotary Shafts

Threaded Rotary Shafts

Attach threaded accessories, such as mixer propellers and fan blades, to the end of these shafts.

Tapped Rotary Shafts

Connect these internally threaded shafts directly to threaded components, or use a fastener to secure.

Keyed Rotary Shafts

Combine with a machine key to transmit torque to gears, sprockets, and other power transmission components.

D-Profile Rotary Shafts

A flat surface area allows set screws to dig into the shaft for securely mounting gears, sprockets, and bearings.

Step-Down Rotary Shafts

A shoulder near the end of the shaft provides a stop for gears, sprockets, and bearings.

Rotary Shafts with Retaining Ring Grooves

Clip retaining rings into the grooves to separate and position gears, sprockets, and bearings.

Threaded Rods

High-Strength Steel Threaded Rods

Comparable to Grade 8 steel, these threaded rods have a tensile strength of 150,000 psi, making them about 25% stronger than medium-strength steel rods.

Medium-Strength Steel Threaded Rods—Grade B7

These Grade B7 threaded rods meet the pressure and temperature requirements of ASTM A193 and are often used to secure pressure tanks, valves, and flanges.

Left-Hand Threaded Medium-Strength
Steel Threaded Rods—Grade B7

Tighten these threaded rods by turning them to the left; once fastened, they resist loosening from counterclockwise motion.

Low-Strength Steel Threaded Rods

About half the strength of medium-strength steel threaded rods, use these for light duty hanging, mounting, and fastening.

Super-Corrosion-Resistant 316
Stainless Steel Threaded Rods

More corrosion resistant than 18-8 and 410 stainless steel threaded rods, these 316 stainless steel rods have excellent resistance to chemicals and salt water.

18-8 Stainless Steel Threaded Rods

18-8 stainless steel threaded rods have good chemical resistance.

Left-Hand Threaded 18-8
Stainless Steel Threaded Rods

Tighten these threaded rods by turning them to the left; once fastened, they resist loosening from counterclockwise motion.

18-8 Stainless Steel Threaded Rods—Grade B8

Grade B8 threaded rods meet the pressure and temperature requirements of ASTM A193 and are often used to secure pressure tanks, valves, and flanges. They have good chemical resistance.

Brass Threaded Rods

Brass threaded rods are corrosion resistant in wet environments, electrically conductive, and nonmagnetic.

Bronze Threaded Rods

Bronze threaded rods are stronger and more resistant to salt water than brass rods.

Aluminum Threaded Rods

One-third the weight of steel, aluminum threaded rods resist corrosion in wet environments.

Partially Threaded Studs with Cotter Pin

Also known as hood pins, these studs have a cotter pin lodged through a drilled hole in the unthreaded portion for light duty holding, such as securing access panels and locking other fasteners.

Coupling Nuts

High-Strength Steel Coupling Nuts—Grade 8

Made from Grade 8 steel, these nuts are about 25% stronger than medium-strength steel coupling nuts. Furnished in inch thread sizes.

Medium-Strength Steel Coupling Nuts—Grade 5

Made from Grade 5 steel, these inch-sized coupling nuts are suitable for most applications.

Low-Strength Steel Coupling Nuts

About half the strength of medium-strength steel coupling nuts, these nuts are for light duty fastening applications.

18-8 Stainless Steel Coupling Nuts

These coupling nuts have good chemical resistance.

Super-Corrosion-Resistant 316
Stainless Steel Coupling Nuts

More corrosion resistant than 18-8 stainless steel coupling nuts, these nuts have excellent resistance to chemicals and salt water.

Brass Coupling Nuts

Brass coupling nuts are corrosion resistant in wet environments and electrically conductive.

Stainless Steel Extra-Long Coupling Nuts

Stainless steel coupling nuts have excellent corrosion resistance in most environments.

Round Coupling Nuts

A smooth rounded body provides a finished look.

Female Thread Adapters

Inch-to-Inch Female Hex Thread Adapters

Connect two differently sized male-threaded parts, such as threaded rods, and tighten with a standard wrench.

Inch-to-Metric Female Hex Thread Adapters

Adapt threaded rods from inch to metric. These adapters connect two male-threaded fasteners, so you can change the gender of a mating part or increase or decrease its thread size. The hex-shaped body fits into the head of a standard wrench.

Connecting Rods

Designed for use with right-hand, internally threaded rod ends, these rods have right-hand threads on both ends. Use them for remote valve operators, throttle controllers, shifting mechanisms, and virtually any push/pull assembly.

Internally Threaded Connecting Rods

Designed for use with right-hand, externally threaded rod ends, these rods have right-hand threads on both ends. Use them for remote valve operators, throttle controllers, shifting mechanisms, and virtually any push/pull assembly.

Turnbuckle-Style Connecting Rods

Similar to turnbuckles, these rods have right-hand threads on one end and left-hand threads on the other so you can make a linkage that adjusts for tension. Add right- and left-hand threaded rod ends to build your linkages.

Internally Threaded
Turnbuckle-Style Connecting Rods

Similar to turnbuckles, these rods have right-hand threads on one end and left-hand threads on the other so you can make a linkage that adjusts for tension.

Ultra-Precision Lead Screws and Nuts

Also known as single-start and self-locking lead screws and nuts, these have a single thread that runs the length of the screw. The nut travels only when the screw turns, so your system won't unexpectedly move when the lead screw is at rest.