We will reply to your message within an hour.
More
Mount the flange to a machine or wall to support idler sprockets and pulleys in tensioning applications. They include washers and a nut to position your component and hold it in place.
Designed for use with right-hand, internally threaded rod ends, these rods have right-hand threads on both ends. Use them for remote valve operators, throttle controllers, shifting mechanisms, and virtually any push/pull assembly.
Designed for use with right-hand, externally threaded rod ends, these rods have right-hand threads on both ends. Use them for remote valve operators, throttle controllers, shifting mechanisms, and virtually any push/pull assembly.
Grade B7, these threaded rods have a tensile strength about one and a half times stronger than low-strength steel rods. They meet the pressure and temperature requirements of ASTM A193 and are often used to secure pressure tanks, valves, and flanges.
Comparable to Grade 8 steel, these threaded rods have a tensile strength of 150,000 psi, making them about 25% stronger than medium-strength steel rods.
About half the strength of medium-strength steel threaded rods, use these for light duty hanging, mounting, and fastening.
Tighten these threaded rods by turning them to the left; once fastened, they resist loosening from counterclockwise motion. About half the strength of medium-strength steel threaded rods, use them for light duty hanging, mounting, and fastening.
18-8 stainless steel threaded rods have good chemical resistance.
More corrosion resistant than 18-8 and 410 stainless steel threaded rods, these 316 stainless steel rods have excellent resistance to chemicals and salt water.
Made from nylon 6/6, these threaded rods resist oil, grease, and solvents. They’re nonconductive, making them good for use around sensitive electrical components.
Brass threaded rods are corrosion resistant in wet environments, electrically conductive, and nonmagnetic.
One-third the weight of steel, aluminum threaded rods resist corrosion in wet environments.
Titanium threaded rods have a high strength-to-weight ratio and are resistant to acids and salt water.
Screw these studs into a tapped hole and use them as a pivot point, hinge, shaft, or locator pin.
These studs have good chemical resistance. Weld them to stainless steel surfaces.
Weld these studs to uncoated steel surfaces.
Pass these studs through a hole and weld them in place.
18-8 stainless steel studs have good chemical resistance and may be mildly magnetic. Also known as hanger bolts, use them to hang, mount, and fasten parts to wood structures.
These studs are also known as hanger bolts—use them to hang, mount, and fasten parts to wood structures.
These steel studs are zinc plated to resist corrosion in wet environments.
18-8 stainless steel studs have good chemical resistance.
Add a stud to thin material when you only have access to one side.
About half the strength of medium-strength steel coupling nuts, these nuts are for light duty fastening applications.
Made from Grade 5 steel, these inch-sized coupling nuts are suitable for most applications.
These coupling nuts have good chemical resistance.
More corrosion resistant than 18-8 stainless steel coupling nuts, these nuts have excellent resistance to chemicals and salt water.
Brass coupling nuts are corrosion resistant in wet environments and electrically conductive.
One-third the weight of steel, aluminum coupling nuts resist corrosion in wet environments.
Stainless steel coupling nuts have excellent corrosion resistance in most environments.
Use the sight hole to check for proper thread engagement.
Often called sleeve nuts, these thread adapters fasten parts with right-hand threads to parts with left-hand threads.
Connect two differently sized male-threaded parts, such as threaded rods, and tighten with a standard wrench.
Adapt threaded rods from inch to metric. These adapters connect two male-threaded fasteners, so you can change the gender of a mating part or increase or decrease its thread size. The hex-shaped body fits into the head of a standard wrench.
A metal case protects the magnetic material.
Alnico magnets resist temperatures up to 420° F.
A steel case concentrates and focuses the magnetic field. It also protects the magnetic material.
Ceramic magnets resist demagnetization better than other magnets and are an economical choice. They resist temperatures up to 140° F.