We will reply to your message within an hour.
Connect these internally threaded shafts directly to threaded components, or use a fastener to secure. They have a flat surface area that allows set screws to dig into the shaft for securely mounting gears, sprockets, and bearings.
Connect these internally threaded shafts directly to threaded components, or use a fastener to secure.
Attach threaded accessories, such as mixer propellers and fan blades, to the end of these shafts.
Designed for use with right-hand, internally threaded rod ends, these rods have right-hand threads on both ends. Use them for remote valve operators, throttle controllers, shifting mechanisms, and virtually any push/pull assembly.
Designed for use with right-hand, externally threaded rod ends, these rods have right-hand threads on both ends. Use them for remote valve operators, throttle controllers, shifting mechanisms, and virtually any push/pull assembly.
Similar to turnbuckles, these rods have right-hand threads on one end and left-hand threads on the other so you can make a linkage that adjusts for tension. Add right- and left-hand threaded rod ends to build your linkages.
Similar to turnbuckles, these rods have right-hand threads on one end and left-hand threads on the other so you can make a linkage that adjusts for tension.
Grade B7, these threaded rods have a tensile strength about one and a half times stronger than low-strength steel rods. They meet the pressure and temperature requirements of ASTM A193 and are often used to secure pressure tanks, valves, and flanges.
Comparable to Grade 8 steel, these threaded rods have a tensile strength of 150,000 psi, making them about 25% stronger than medium-strength steel rods.
About half the strength of medium-strength steel threaded rods, use these for light duty hanging, mounting, and fastening.
18-8 stainless steel threaded rods have good chemical resistance.
More corrosion resistant than 18-8 and 410 stainless steel threaded rods, these 316 stainless steel rods have excellent resistance to chemicals and salt water.
Grade B8M threaded rods meet the pressure and temperature requirements of ASTM A193 and are often used to secure pressure tanks, valves, and flanges.
Made from nylon 6/6, these threaded rods resist oil, grease, and solvents. They’re nonconductive, making them good for use around sensitive electrical components.
These acetal threaded rods won't absorb moisture like nylon and fiberglass rods, so they're good for use in wet environments. They resist alcohol, gasoline, and solvents.
Brass threaded rods are corrosion resistant in wet environments, electrically conductive, and nonmagnetic.
One-third the weight of steel, aluminum threaded rods resist corrosion in wet environments.
Screw these studs into a tapped hole and use them as a pivot point, hinge, shaft, or locator pin.
These studs have good chemical resistance. Weld them to stainless steel surfaces.
Weld these studs to uncoated steel surfaces.
Pass these studs through a hole and weld them in place.
These steel studs are zinc plated to resist corrosion in wet environments.
18-8 stainless steel studs have good chemical resistance.
316 stainless steel studs have excellent resistance to chemicals and salt water.
Add a stud to thin material when you only have access to one side.
To remove these pins, thread a screw or tool into the tapped hole, then pull them out.
The flat side of these pins relieves trapped air, making them easier to insert in and remove from blind holes. To remove, thread a screw or tool into the tapped hole, then pull the pin out.
A spiral groove cut into these pins relieves trapped air but stays in 360° contact with the hole for a secure fit that's easy to insert in and remove from blind holes. To remove, thread a screw or tool into the tapped hole, then pull the pin out.
About half the strength of medium-strength steel coupling nuts, these nuts are for light duty fastening applications.
Made from Grade 5 steel, these inch-sized coupling nuts are suitable for most applications.
These coupling nuts have good chemical resistance.
More corrosion resistant than 18-8 stainless steel coupling nuts, these nuts have excellent resistance to chemicals and salt water.
Brass coupling nuts are corrosion resistant in wet environments and electrically conductive.
One-third the weight of steel, aluminum coupling nuts resist corrosion in wet environments.
Plastic coupling nuts are chemical resistant, nonconductive, and lightweight.
Stainless steel coupling nuts have excellent corrosion resistance in most environments.
A smooth rounded body provides a finished look.
Use the sight hole to check for proper thread engagement.
Position components in assemblies, as well as separate or connect parts with these standoffs.
A nylon patch bonded to the threads adds friction, preventing these standoffs from loosening from vibration.
Also known as captive standoffs, a recess under the hex clinches the panel for a strong hold that won't push, pull, or twist out. When mounted, the hex sits flush with the surface and the closed end creates a neat, finished appearance.
A recess under the hex clinches a panel for a strong hold that won't push, pull, or twist out. When mounted with a lever press, the hex sits flush with the surface and the open end creates a through hole.
Often called sleeve nuts, these thread adapters fasten parts with right-hand threads to parts with left-hand threads.
Connect two differently sized male-threaded parts, such as threaded rods, and tighten with a standard wrench.
Adapt threaded rods from inch to metric. These adapters connect two male-threaded fasteners, so you can change the gender of a mating part or increase or decrease its thread size. The hex-shaped body fits into the head of a standard wrench.
A metal case protects the magnetic material.
These ceramic magnets resist demagnetization better than other magnets, and have a metal case to protect the magnetic material. They resist temperatures up to 175° or 245° F.
Alnico magnets resist temperatures up to 420° F.