We will reply to your message within an hour.
Internal threads allow you to mount these shafts onto threaded studs and fasteners, no shaft supports needed.
Comparable to Grade 8 steel, these threaded rods have a tensile strength of 150,000 psi, making them about 25% stronger than medium-strength steel rods.
About half the strength of medium-strength steel threaded rods, use these for light duty hanging, mounting, and fastening.
Tighten these threaded rods by turning them to the left; once fastened, they resist loosening from counterclockwise motion. About half the strength of medium-strength steel threaded rods, use them for light duty hanging, mounting, and fastening.
18-8 stainless steel threaded rods have good chemical resistance.
More corrosion resistant than 18-8 and 410 stainless steel threaded rods, these 316 stainless steel rods have excellent resistance to chemicals and salt water.
Made from nylon 6/6, these threaded rods resist oil, grease, and solvents. They’re nonconductive, making them good for use around sensitive electrical components.
Brass threaded rods are corrosion resistant in wet environments, electrically conductive, and nonmagnetic.
One-third the weight of steel, aluminum threaded rods resist corrosion in wet environments.
Titanium threaded rods have a high strength-to-weight ratio and are resistant to acids and salt water.
Screw these studs into a tapped hole and use them as a pivot point, hinge, shaft, or locator pin.
These studs have good chemical resistance. Weld them to stainless steel surfaces.
Weld these studs to uncoated steel surfaces.
Pass these studs through a hole and weld them in place.
These steel studs are zinc plated to resist corrosion in wet environments.
18-8 stainless steel studs have good chemical resistance.
These studs are also known as hanger bolts—use them to hang, mount, and fasten parts to wood structures.
316 stainless steel studs have excellent resistance to chemicals and salt water.
Add a stud to thin material when you only have access to one side.
To remove these pins, thread a screw or tool into the tapped hole, then pull them out.
The flat side of these pins relieves trapped air, making them easier to insert in and remove from blind holes. To remove, thread a screw or tool into the tapped hole, then pull the pin out.
A spiral groove cut into these pins relieves trapped air but stays in 360° contact with the hole for a secure fit that's easy to insert in and remove from blind holes. To remove, thread a screw or tool into the tapped hole, then pull the pin out.
About half the strength of medium-strength steel coupling nuts, these nuts are for light duty fastening applications.
Made from Grade 5 steel, these inch-sized coupling nuts are suitable for most applications.
These coupling nuts have good chemical resistance.
More corrosion resistant than 18-8 stainless steel coupling nuts, these nuts have excellent resistance to chemicals and salt water.
Brass coupling nuts are corrosion resistant in wet environments and electrically conductive.
One-third the weight of steel, aluminum coupling nuts resist corrosion in wet environments.
Plastic coupling nuts are chemical resistant, nonconductive, and lightweight.
Stainless steel coupling nuts have excellent corrosion resistance in most environments.
A smooth rounded body provides a finished look.
Use the sight hole to check for proper thread engagement.
Position components in assemblies, as well as separate or connect parts with these standoffs.
A nylon patch bonded to the threads adds friction, preventing these standoffs from loosening from vibration.
Protect components from electrical charges.
Also known as captive standoffs, a recess under the hex clinches the panel for a strong hold that won't push, pull, or twist out. When mounted, the hex sits flush with the surface and the closed end creates a neat, finished appearance.
A recess under the hex clinches a panel for a strong hold that won't push, pull, or twist out. When mounted with a lever press, the hex sits flush with the surface and the open end creates a through hole.
Thread the male connection into a tapped hole and snap the other end into a panel for a secure hold that can be released for repairs and upgrades.
Often called sleeve nuts, these thread adapters fasten parts with right-hand threads to parts with left-hand threads.
Connect two differently sized male-threaded parts, such as threaded rods, and tighten with a standard wrench.
Adapt threaded rods from inch to metric. These adapters connect two male-threaded fasteners, so you can change the gender of a mating part or increase or decrease its thread size. The hex-shaped body fits into the head of a standard wrench.
A metal case protects the magnetic material.
These ceramic magnets resist demagnetization better than other magnets, and have a metal case to protect the magnetic material. They resist temperatures up to 175° or 245° F.
A steel case concentrates and focuses the magnetic field. It also protects the magnetic material.