We will reply to your message within an hour.
Multiple thread channels (also known as thread starts) create faster linear travel than lead screws with a single thread start.
Internal threads allow you to mount these shafts onto threaded studs and fasteners, no shaft supports needed.
Mount these externally threaded shafts into tapped holes rather than using a shaft support, or attach a hex nut, shaft collar, or other threaded accessory.
Designed for use with right-hand, internally threaded rod ends, these rods have right-hand threads on both ends. Use them for remote valve operators, throttle controllers, shifting mechanisms, and virtually any push/pull assembly.
Designed for use with right-hand, externally threaded rod ends, these rods have right-hand threads on both ends. Use them for remote valve operators, throttle controllers, shifting mechanisms, and virtually any push/pull assembly.
Similar to turnbuckles, these rods have right-hand threads on one end and left-hand threads on the other so you can make a linkage that adjusts for tension. Add right- and left-hand threaded rod ends to build your linkages.
Similar to turnbuckles, these rods have right-hand threads on one end and left-hand threads on the other so you can make a linkage that adjusts for tension.
Made from stainless steel for excellent corrosion resistance in damp environments.
Thread these ball socket end fittings onto gas springs. They rotate in any direction on a ball stud to compensate for misalignment.
Made of Grade B7 steel, the tensile strength of these threaded rods is one and a half times higher than low-strength steel threaded rods. They also meet the pressure and temperature requirements of ASTM A193 and are often used to secure pressure tanks, valves, and flanges.
The tensile strength of these metric Grade B7 rods is about one and a half times higher than low-strength steel rods.
An economical alternative to Grade B7 and Grade B16 threaded rods, these metric Class 8.8 rods are suitable for fastening most machinery and equipment.
These metric threaded rods are about half the strength of medium-strength steel threaded rods for light duty hanging, mounting, and fastening.
About half the strength of medium-strength steel threaded rods, use these metric fine-thread rods for light duty hanging, mounting, and fastening.
These metric threaded rods tighten when turned to the left; once fastened, they resist loosening from counterclockwise motion. About half the strength of medium-strength steel threaded rods, use them for light duty hanging, mounting, and fastening.
Available in metric sizes, these 18-8 stainless steel threaded rods have good chemical resistance.
These metric 316 stainless steel threaded rods are more corrosion resistant than 18-8 and 410 stainless steel threaded rods and have excellent resistance to chemicals and salt water.
These metric threaded rods are made from nylon 6/6 and resist oil, grease, and solvents. They’re nonconductive, making them good for use around sensitive electrical components.
These metric brass threaded rods are corrosion resistant in wet environments, electrically conductive, and nonmagnetic.
Screw the threaded end of these metric studs into a tapped hole and use the unthreaded end as a pivot point, hinge, shaft, or locator pin.
Also known as setup studs, these studs withstand sideways forces better than fully threaded studs because they have an unthreaded middle that is stronger than the treaded ends.
These metric 316 stainless steel studs have excellent resistance to chemicals and salt water. Also known as hanger bolts, use them to hang, mount, and fasten parts to wood structures.
These steel studs are zinc plated to resist corrosion in wet environments.
18-8 stainless steel studs have good chemical resistance.
316 stainless steel studs have excellent resistance to chemicals and salt water.
To remove these pins, thread a screw or tool into the tapped hole, then pull them out.
The flat side of these pins relieves trapped air, making them easier to insert in and remove from blind holes. To remove, thread a screw or tool into the tapped hole, then pull the pin out.
For light duty applications, choose these metric-sized coupling nuts.
Choose these locknuts to fasten standard metric threads. They’re Class 8 steel, so they can be used in most fastening applications.
These metric coupling nuts have good chemical resistance.
More corrosion resistant than 18-8 stainless steel coupling nuts, these metric nuts have excellent resistance to chemicals and salt water.
Brass coupling nuts are corrosion resistant in wet environments and electrically conductive.
One-third the weight of steel, aluminum coupling nuts resist corrosion in wet environments.
Plastic coupling nuts are chemical resistant, nonconductive, and lightweight.
Stainless steel coupling nuts have excellent corrosion resistance in most environments.
Known for their strength, steel coupling nuts are available with a corrosion-resistant finish.
A smooth rounded body provides a finished look.
Position components in assemblies, as well as separate or connect parts with these standoffs.
A nylon patch bonded to the threads adds friction, preventing these standoffs from loosening from vibration.
Also known as captive standoffs, a recess under the hex clinches the panel for a strong hold that won't push, pull, or twist out. When mounted, the hex sits flush with the surface and the closed end creates a neat, finished appearance.
A recess under the hex clinches a panel for a strong hold that won't push, pull, or twist out. When mounted with a lever press, the hex sits flush with the surface and the open end creates a through hole.
Often called sleeve nuts, these thread adapters fasten parts with right-hand threads to parts with left-hand threads.
Adapt threaded rods from inch to metric. These adapters connect two male-threaded fasteners, so you can change the gender of a mating part or increase or decrease its thread size. The hex-shaped body fits into the head of a standard wrench.
Increase or decrease metric thread size from one male-threaded part to another. Commonly used to connect two differently sized threaded rods, they have a hex-shaped body, so you can tighten them with a standard wrench.
Typically used with high-pressure brass and bronze threaded pipe fittings.
A metal case protects the magnetic material.
A rubber cover protects the mounting surface as well as the magnet.
A steel case concentrates and focuses the magnetic field. It also protects the magnetic material.
A rubber cover protects the magnet and mounting surface.
Ceramic magnets resist demagnetization better than other magnets and are an economical choice. They resist temperatures up to 140° F.