Also known as cam followers, track rollers support loads while guiding and positioning work. Thread the stud directly into a component or secure with a nut for through-hole mounting.

Because they never need to be relubricated, these rollers are a good choice for hard-to-reach places.

Also known as eccentric track rollers, the shoulder adjusts up or down to align to your track, enabling uniform alignment among rollers in a system.

Lubricated with graphite, these rollers can handle temperatures from -450° to 750° F—the widest temperature range of any track roller in our offering.

With dry-running PTFE sleeve bearings, these rollers don’t require lubricant. They’re also fully submersible, nonsparking, and lightweight.

Also known as yoke-style cam followers, these rollers have more mounting flexibility than threaded track rollers. They're typically mounted onto a shaft or clevis rod end.

Made of 440C stainless steel, these shaft-mount track rollers resist corrosion in damp environments.

Also known as yoke-style cam followers, these rollers have more mounting flexibility than threaded track rollers. They're typically mounted onto a shaft or clevis rod end.

Also known as eccentric track rollers, the shoulder adjusts up or down to align to your track, enabling uniform alignment among rollers in a system.

Support and guide loads on angle rails in food, pharmaceutical, and other sanitary environments. Also known as yoke-style cam followers, these track rollers offer more mounting flexibility than threaded alternatives and are typically mounted on shafts and clevis rod ends.

Thread the stud directly into a component or secure with a nut for through-hole mounting.

Carry loads along a track with this series of smooth-rolling alternating vertical and horizontal wheels.

Track provides the runway for trolleys, carriers, and chain in manual and powered systems.

Use brackets to hang and join sections of enclosed track.

Conveyor guides direct and position material.

Choose the channel and wear strip or brush you need for your application.

Use these guides when positioning static-sensitive material such as electronic equipment.

Use brackets and connectors to create vertical and horizontal support arms.

Graduated in 1/8" increments, these rods make it easy to align multiple brackets during installation.

Spacers increase the distance between a bracket and the conveyor frame.

Suspend trays, plates, and drip pans underneath a conveyor.

Also known as cross blocks, connectors join rods at different angles.

Idler wheels keep the belt moving and prevent sagging.

Mount along a wall or other vertical surface.

Create a self-aligning carriage and guide rail system to compensate for mounting surfaces that aren't parallel.

V-shaped rollers and rails allow these carriages to operate well in dirty environments because the debris won't get trapped on the rail.

Nylon rollers provide low-friction movement for light loads and corrosive environments.

A handle on the side of the carriage locks the carriage in place.

Made of stainless steel, these track rollers and guide rails are more corrosion resistant than steel rollers and rails.

Mate with a T-slotted rail to add linear motion to your assembly.

A handle on the side of the carriage locks the carriage in place.

Threaded inserts secure the bearing to the carriage and prevent it from loosening due to frequent starts and stops.

Fasten loads on the side of these carriages and add linear motion to a T-slot assembly.

With a wide base, these sleeve bearing carriages stabilize moment (twisting) and off-center loads better than standard carriages. Use in areas where multiple carriages or rails won't fit.

For applications with low clearance, these carriages protrude less than 5 mm above their rails.

Mount to vertical surfaces for applications where tight tolerances aren't required.

These carriages and guide rails are steel.

These carriages and guide rails are steel.

Made of stainless steel, these carriages and guide rails are more corrosion resistant than steel carriages and guide rails.

Suitable for clean room use, these carriages and guide rails are made entirely of stainless steel.

Run many cycles in tight spaces before replacing or re-greasing carriages.

Create your own positioning table or telescoping slide. Sets include four rails, two roller bearing cages, and eight end stops.

With a row of crossed-roller bearings on each side of the rail, these slides have over twice the load capacity of standard low-friction slides and are better for handling shock loads.

A linear scale and micrometer-like hand wheel measure travel distance in increments of 0.001".

Made with Frelon bearings, these slides have over four times the load capacity of standard positioning slides.

Two micrometer handles ensure accurate, repeatable positioning along two axes—good for positioning parts, such as measuring and inspecting equipment, that are part of a larger automated system.

Three micrometer handles ensure accurate, repeatable positioning along three axes—good for positioning parts, such as measuring and inspecting equipment, that are part of a larger automated system.

Use these rollers as replacements on an existing door hanger or as the starting point for a customized hanger.

Combine track, mounting brackets, and hangers to create a system for hanging doors.

Narrow track allows you to hang doors in tight spaces.

Curved track pieces allow you to create a wide variety of layouts for doors, curtains, and strip doors.

Built to withstand corrosive marine environments, track is anodized aluminum and hangers are 316 stainless steel.

To prevent drawers from slamming shut and support them even if they’re tall and full of heavy equipment, these steel slides have soft-closing bumpers and mount to the top and bottom of drawers.

A stop holds the drawer closed; pull firmly on the drawer to open.

Half the length of other drawer slides we sell, these slides install in small-parts cabinets.

The stacked design provides stability for deep and wide drawers.

When you push on the drawer, these slides force the drawer open.

A stop holds the drawer open; push firmly on the drawer to close.