This wire rope provides a good balance of abrasion resistance and flexibility.

Often used as bracing and guy wires, individual strands are thick solid wire for a stiff construction.

This wire rope provides a good balance of abrasion resistance and flexibility.

More wires per strand than other wire rope provides the flexibility required for repeat bending over drums and pulleys.

This braided wire has a stiff construction for use as bracing and guy wires.

This wire rope provides a good balance of abrasion resistance and flexibility.

More wires per strand than other wire rope provides the flexibility required for repeat bending over drums and pulleys.

Flattened outer strands create a smooth surface area that spreads contact to reduce wear.

These clamps must be oriented with the saddle on the long (live) end and the U-bolt on the short (dead) end. They’re also known as wire rope clips.

Install these clamps without any specific orientation, slide the nut over the rope and tighten it onto the threaded halves with a torque wrench.

A clamp and thimble in one convenient fitting simplifies installation while providing support and fray protection to the wire rope loop. Use a torque wrench to tighten the clamp.

Also known as standard-pattern thimbles, these provide better protection against fraying than light duty thimbles.

The open-end design leaves more room for connections than other thimbles.

Install these clevis-end plug-lock fittings on the end of wire rope for a strong hold and finished appearance.

Install these swivel-hook-end plug-lock fittings on the end of wire rope for a strong hold and finished appearance.

A thimble on the inside of the loop protects the wire rope from fraying.

Create a choker loop around a supporting structure with the snap-hook end and use the loop to secure the suspended material.

Attach the 90° eye to a surface for support and use the loop to secure the suspended material.

The swivel fork ends allow the lanyard to rotate freely.

With a reinforced loop, also known as a thimble eye, installed on one end, quickly attach a hook or a shackle to a wire rope.

The galvanized finish resists corrosion.

A stop, also known as a ferrule fitting, installed on one end holds the rope in place.

Screw the pin into position by hand for quick installation and removal. They're for use in low-vibration applications where the shackle remains stationary.

Screw the pin into position by hand for quick installation and removal. They're for use in low-vibration applications where the shackle remains stationary.

Screw the pin into position by hand for quick installation and removal. They're for use in low-vibration applications where the shackle remains stationary.

The strongest shackles we offer, these connectors have a pin with flush ends that prevents snagging and accidental disengagement.

The pins have flush ends to prevent snagging and accidental disengagement.

Create fast connections with items, such as rope, chain, and straps.

Also known as quick links, these links thread closed by hand or with a wrench.

Flat sides allow webbing and strapping to lay flat, so they won't slide and bunch.

The twisted shape of these links prevents loads from rotating or knotting.

Also known as lap links or repair links.

Strike the prongs with a ball peen hammer and they expand to hold the connecting link together.

Hang, pull, and secure loads. These rings are good for general non-lifting applications.

Smaller than lifting oblong links, these links provide room for snaps, carabiners, and other non-lifting connectors.

Also known as master and sling links, a large inner diameter provides room to attach multiple connectors or legs on a sling.

Providing better load distribution and alignment than single oblong links, these reduce wear in three and four leg slings.

Commonly used in conjunction with connecting links to meet OSHA 29 CFR 1910.184.

Hammer the pin through the center to assemble these links. They’re also known as hammer locks and sling links.

The flat side lets webbing and strapping lay flat, so they don’t slide and bunch.

A latch ensures rope, chain, and fittings won't separate from the hook when the load slackens.

A latch ensures rope, chain, and fittings won't separate from the hook when the load slackens. The hook opening accommodates large anchor points and allows chain to move freely through the closed hook.

These rotate for easy positioning before a load is applied. They have a latch to ensure rope, chain, and fittings won't separate from the hook when the load slackens.

Screw these hooks into place and secure with the included nut.

These rotate for easy positioning before a load is applied.

For a more secure connection than standard hooks, these clevis hooks have a latch that locks closed when a load is applied.

These hooks swivel under load. They have a latch locks closed when a load is applied for a more secure connection than standard hooks.

With a narrow opening and contoured sides, these securely hold a single link of chain to prevent overtightening when lifting a load.

A spring-loaded pin ensures chain won't separate from the hook when the load slackens. Connect your chain to the eye end.

Also known as foundry hooks, use these on thick molds, castings, and objects that don't have attachment points.

These swivel hooks have a latch that ensures rope, chain, and fittings won't separate from the hook when the load slackens.

Weld these hooks into place.

An unthreaded shank allows you to cut your own threads.

Often used in binding and tie-down applications, these hooks have a narrow opening to securely hold a single link of chain.

Designed for angular lifting, hoist rings resist stresses that would bend or break an eyebolt. They have a lifting ring that pivots 180° front to back to compensate for roll and sway when lifting heavy or unbalanced loads.

Choose these hoist rings when you need to lift your load from the side.

Join, organize, and suspend objects with these S-hooks.

One side is closed and the other is open.

These hooks have closed ends on both sides.

Rotating for easy positioning before a load is applied, these minimize twisting and knotting of rope and chain.

These rotate for easy positioning before a load is applied to minimize twisting and knotting of rope and chain.

Minimize twisting and knotting of rope and chain and adjust the position of a fitting or an object under load.

Also known as seizing bands, these prevent fraying while cutting wire rope. Wrap the band around the wire rope and squeeze the flat end into the indented end.

Attach these clamps by running a wire rope through the jaws to create an attachment point anywhere along the wire rope.

Attach these hooks to elastic cord to make a tie down.

Create a tie down by attaching these hooks to elastic strap.

Sew webbing onto these plates for a permanent anchor point or run webbing through to use them as guides.

Use the split in the hook to slide a loop on and off these fittings.

These slings are more abrasion and cut resistant than web and round slings, yet lighter in weight than mesh and chain slings.

Mount these pulleys to a flat surface to assist with horizontal pulling or to guide a rope.

Also known as sheaves, use these pulleys to assist with horizontal pulling or to guide a rope.