Free of metal particles, these lubricants won’t react with stainless steel. Also known as thread lubricants, antiseize lubricants prevent threaded fasteners and close-fitting parts from locking together due to corrosion, contamination, or heat.

Corrosion-resistant additives allow these lubricants to prevent parts from locking together in caustic environments, such as steel mills and power plants.

Often used with engine bolts and heavily-loaded, slow-moving gears, these lubricants are formulated with moly (molybdenum disulfide) to prevent parts from locking together under high loads and pressure.

Copper allows these lubricants to conduct electricity, while graphite gives them good chemical and corrosion resistance. Use them to prevent threaded fasteners and close-fitting parts from locking together in connections where you need to conduct electricity.

Use these lubricants to prevent threaded fasteners and close-fitting parts in food-processing and preparation areas from locking together. They're NSF registered H1 for incidental food contact.

These lubricants dry to form a thin, solvent-resistant film that won't squeeze out or attract dirt. Use them to prevent threaded fasteners and close-fitting parts from locking together.

Formulated for use on soft metal, such as aluminum, copper, and brass, these lubricants won’t stain. They reduce friction between your cutting tool and workpiece to make cutting cycles faster and easier, improve surface finishes, and extend tool life.

These general purpose lubricants reduce friction between your cutting tool and workpiece to make cutting cycles faster and easier, improve surface finishes, and extend tool life.

A high sulfur concentration provides the lubricity required to protect tools and stainless steel work surfaces, but these lubricants will stain other metal. They reduce friction between your cutting tool and workpiece to make cutting cycles faster and easier.

For use in food-processing and preparation areas, these lubricants are NSF registered H1 for incidental food contact. They reduce friction between your cutting tool and workpiece to make cutting cycles faster and easier, improve surface finishes, and extend tool life.

Prevent workpieces from sticking to saw and receiving tables. These lubricants make a dry, slippery film that protects tables from corrosion and that won’t come off on your workpiece. Made without silicone or petroleum, they won’t stain wood or interfere with glue or finishes.

Apply just a few drops of these coolants to your cutting tools before and during milling and machining to reduce heat with very little cleanup.

These coolants prevent material buildup on smoothing and sharpening stones. They are water-based, so they’re easy to clean from workpieces.

Use these lubricants to ensure smooth, consistent motion when pulling wire or cable through conduit. They provide long-lasting lubrication to support repositioning and maintenance after initial cable installation. Compatible with all cable and insulation types.

For use with roller chain and other moving metal parts, these thin lubricants cut through dirt, grease, and rust, withstand heavy loads, and resist wear.

These lubricants foam when applied, so they don’t drip while sinking into roller chain and other moving metal parts. They dry to form a film that prevents dust, dirt, and corrosion.

Use these NSF registered H1 lubricants in food-processing and preparation areas with a risk of incidental food contact. They form a nonstick film that won't attract contaminants, such as flour.

A high load-carrying capacity makes these lubricants good for use on chain and moving metal parts. They dry to form a film that lubricates without attracting dust.

Spray these wear-resistant lubricants on rollers, hinges, and tracks of overhead doors to reduce friction and noise. PTFE provides excellent lubricity, while silicone repels water for use outdoors. Once dry, these lubricants form a thin lubricating layer that won’t rub off or attract dust.

Prevent packages from sticking on conveyor rails and chutes. Made with silicone, use these lubricants to create a slippery dry film that won’t attract dust where metal and non-metal surfaces meet.

Use these lubricants to release large, intricate, or difficult-to-release parts. Also known as paintable mold-release lubricants, they don’t leave a residue, so you can paint or finish the molded part without the need to clean it. They allow you to easily remove cast parts and prevent sticking, stretching, and tearing.

Also known as paintable mold-release lubricants, these lubricants don’t leave a residue, so you can paint or finish the molded part without the need to clean it. Use them for molding and casting parts in food-processing and preparation areas, or when molding parts that will be used around food. They allow you to easily remove cast parts and prevent sticking, stretching, and tearing.

Made of 98% moly, this lubricant withstands pressure up to 500,000 psi and has excellent wear resistance. Apply it to metal surfaces to prevent parts from corroding or sticking.