The standard for high-strength fastening.

Tighten these screws by turning them to the left; once fastened, they prevent counterclockwise-moving parts from loosening.

Use these general purpose 18-8 stainless steel screws for a variety of fastening applications. They have good chemical resistance.

Tighten these screws by turning them to the left; once fastened, they prevent counterclockwise-moving parts from loosening. Made from 18-8 stainless steel, these screws have good chemical resistance.

Often used to fasten parts in engines and turbines, these are our strongest stainless steel screws. They are comparable in strength to alloy steel with the corrosion resistance of 18-8 stainless steel.

Plastic screws are chemical and oil resistant, nonconductive, and lightweight.

Our most corrosion-resistant metal screws, titanium screws withstand salt water, acids, and chemicals. They have a high strength-to-weight ratio and are about 40% lighter than steel screws.

More corrosion resistant than stainless steel screws, nickel alloy screws have excellent resistance to salt water and some acids.

Nearly as strong as steel, these stainless steel screws won’t rust in outdoor, washdown, and other corrosive environments. With half the height of a standard socket head, these low-profile screws fit in tight spaces.

Made from alloy steel, these screws are nearly twice as strong as stainless steel low-profile screws. With a head height one-third the size of a standard socket head, they fit in the tightest spaces.

With a head one and a half times taller than a standard socket head, these screws are easier to install in deep counterbored holes and other hard-to-reach places.

For use where sideways forces are a concern, these screws have a precisely measured unthreaded portion (grip) for a strong hold. Their flanged head distributes pressure where the screw meets the surface, so you don't need a washer.

More corrosion resistant than 18-8 stainless steel screws, these screws have excellent resistance to chemicals and salt water. They have a thread locker to resist vibration.

Stainless steel screws have excellent corrosion resistance in most environments. Wire these screws together for more vibration resistance than other types of socket head screws.

Stainless steel screws have excellent corrosion resistance in most environments. They have a split lock washer to create tension and resist loosening from vibration.

Drilled through the head and shaft, these screws vent fluid and gases trapped below the screw, making them good for vacuum applications.

Seal out contaminants and prevent leaks—a rubber O-ring under the head prevents leaks and seals out contaminants.

The nylon patch bonded to the threads of these socket head screws adds friction to keep vibration from loosening them, while their O-ring prevents leaks and seals out contaminants.

18-8 stainless steel button head screws have good chemical resistance and may be mildly magnetic.

18-8 stainless steel pan head screws have good chemical resistance and may be mildly magnetic.

Choose these screws for their adherence to strict military standards for material and construction.

Choose these screws for their adherence to strict military standards for material and construction.

Reliable in harsh environments up to 500° F, PEEK screws withstand acids, bases, and salt solutions. They are chemical and oil resistant, nonconductive, and lightweight.

Brass pan head screws are corrosion resistant in wet environments, nonmagnetic, and electrically conductive.

These 18-8 stainless steel screws have good chemical resistance and may be mildly magnetic. The extra-wide truss head distributes holding pressure to reduce the likelihood of crushing thin material.

Stainless steel screws have excellent corrosion resistance in most environments.

18-8 stainless steel pan head screws have good chemical resistance and may be mildly magnetic.

These pan head screws are zinc plated for corrosion resistance in wet environments.

PTFE screws withstand harsh chemicals and temperatures from -100° F to 500° F. They are nonconductive, lightweight, and resist wear due to their slippery surface.

Made from brass, these screws are corrosion resistant in wet environments, nonmagnetic, and electrically conductive.

More corrosion resistant than 18-8 stainless steel screws, these screws have excellent resistance to chemicals and salt water.

One-third the weight of steel, aluminum screws resist corrosion in wet environments.

These screws have good chemical resistance.

A zinc plating provides mild corrosion resistance.

Stainless steel screws have excellent corrosion resistance in most environments.

Brass screws are corrosion resistant in wet environments, nonmagnetic, and electrically conductive.

A zinc plating provides mild corrosion resistance.

Made from 18-8 stainless steel, these screws have good chemical resistance and may be mildly magnetic. Torx and Torx-Plus drives have more points of contact than other drives, allowing you to tighten the screw without damaging the recess.

A286 stainless steel screws have comparable strength to alloy steel with the corrosion and chemical resistance of 18-8 stainless steel. They have a Torx drive that has more points of contact than other drives, allowing you to tighten the screw without damaging the recess.

These screws have a Torx or Torx-Plus drive for more points of contact than other drives, allowing you to tighten the screw without damaging the recess.

Made from stainless steel, these screws are chemical resistant and may be mildly magnetic.

18-8 stainless steel screws have good chemical resistance and may be mildly magnetic. The flange distributes pressure across a wide surface, eliminating the need for a separate washer.

Made from alloy steel, these screws are nearly twice as strong as stainless steel button head screws. They have a flange that distributes pressure across a wide surface, eliminating the need for a separate washer.

Made from 18-8 stainless steel, these screws have good chemical resistance and may be mildly magnetic. The flange is wider and thicker than our other flanged screws, so they distribute pressure the best.

These stainless steel screws have good chemical resistance and may be mildly magnetic. The washer has sharp internal teeth that dig into surfaces to resist large amounts of vibration while the smooth outside edge provides a finished look. Also known as Sems screws, the washer rotates freely but is permanently attached.

Made from stainless steel, these screws have good chemical resistance and may be mildly magnetic. All have a washer with sharp external teeth that dig into surfaces for maximum holding power and vibration resistance. Also known as Sems screws, the washer rotates freely but is permanently attached.

Made from stainless steel, these screws have good chemical resistance and may be mildly magnetic. A curved washer protects delicate surfaces while providing constant tension. Also known as Square Cone Sems screws, the washer rotates freely but is permanently attached.

When compressed, the split lock washer flattens to add tension and prevent loosening from small amounts of vibration. Also known as Sems screws, the washer rotates freely but is permanently attached.

The flat washer distributes holding pressure and protects delicate surfaces from damage while the split lock washer adds tension to prevent loosening from small amounts of vibration.

Made from alloy steel, these screws are nearly twice as strong as stainless steel button head screws.

The epoxy adhesive on the threads provides twice the holding power of standard thread-locking screws, but requires time to harden.

These 18-8 stainless steel button head screws have good chemical resistance and may be mildly magnetic. The tamper-resistant Torx drive (also known as a pin-in Torx drive) makes them difficult to remove without special tools.

Made from alloy steel, these screws are nearly twice as strong as stainless steel button head screws. Their tamper-resistant Torx drive (also known as a pin-in Torx drive) makes them difficult to remove without special tools.

The extra-wide head distributes holding pressure to reduce the likelihood of crushing thin materials.

Made from alloy steel, these screws are nearly twice as strong as stainless steel button head screws.

A zinc plating provides mild corrosion resistance.

A rubber O-ring prevents leaks and seals out contaminants. Made from 18-8 stainless steel, these screws have good chemical resistance and may be mildly magnetic.

Made from Grade 8 steel, these screws can be used in high-stress applications, such as valves, pumps, motors, and automotive suspension systems. They are at least 25% stronger than medium-strength steel screws.

When clearance for a wrench is limited, these screws have a Phillips drive so you can install them with a screwdriver. They are used for high-strength fastening.

Tighten these screws by turning them to the left; once fastened, they prevent counterclockwise-moving parts from loosening. For use in high-strength fastening applications.