Protect your feet from chemical spills and splashes. All boots are water resistant.

PVC/polyurethane blend has excellent resistance against inorganic and mineral acids. It also resists oils and grease. Neoprene has excellent resistance against alkalies and is softer than PVC/polyurethane.

6" high boots cover the ankle. 12" high boots are mid-calf boots. 15" and 16" high boots are knee high.

Boots with a safety toe meet ASTM F2413 standards for protection against impact and compression.

Style A are made from a PVC/polyurethane blend and have excellent resistance to acids, oil, and grease. A steel-reinforced toe adds safety. A shank provides arch support by distributing weight during strenuous work, such as climbing ladders.

Style B are made from neoprene, they have excellent resistance against alkalies. Boots with a safety toe are reinforced with steel for protection.

Style C provide knee-high coverage. Made from a PVC/polyurethane blend, they have excellent resistance to acids, oil, and grease. For added protection, boots with a safety toe are reinforced with steel. Boots with a shank offer arch support by distributing weight during strenuous work, such as climbing ladders. Boots with a reinforced midsole protect against punctures when working around sharp objects, such as glass, nails, and scrap metal.

Style D boots are a PVC/polyurethane blend and provide knee-high coverage against acids, oil, and grease. Boots with a safety toe are reinforced with steel for protection. For added arch support, a shank distributes weight during strenuous work, such as climbing ladders.

Keep feet warm and dry in frigid temperatures with these insulated boots. They have a safety toe that’s made of steel or lightweight composite and meets ASTM F2413 standards for protection against impact and compression.

Men’s boots are made of oil- and water-resistant leather. 8" high boots cover the ankle; they have a skid-resistant sole that grips wet and slippery surfaces for good traction. 11" high boots are mid-calf boots.

Women’s boots are made of oil-resistant rubber and are knee-high.

Also known as firefighters' boots, these meet the NFPA 1971 standard for structural firefighting. They have a Kevlar lining throughout and a foam insole to withstand ambient heat up to 500° F. These boots are knee high and made of water-resistant blended rubber. They have a safety toe that meets ASTM F2413 standards for protection against impact and compression. A shank provides arch support by distributing weight during strenuous work, such as climbing ladders.

Wear these guards over shoes or boots to shield toes and feet from accidental impact. Steel and aluminum guards meet ASTM F2413 for protection against accidental impact and compression up to 75 ft.-lbs.

Order your normal shoe size. For large work shoes, order one size up. Guards with a foot strap and snaps are designed to fit over large work shoes or boots, so order your normal shoe size.

These covers are ASTM F2413 rated and tested to 20,000 volts AC for protection against electrical hazards. They are made of water-resistant dielectric rubber with a fabric lining for easy removal. A skid-resistant sole grips wet and slippery surfaces for good traction. They have a deep-cut heel that locks onto ladder rungs or stair edges to stabilize the wearer when climbing.

Order your normal shoe size unless wearing over large work shoes, then order one size up.

These covers are ASTM F2413 rated and tested to 20,000 volts AC for protection against electrical hazards. They are knee high and made of water-resistant dielectric rubber with a fabric lining for easy removal. A skid-resistant sole grips wet and slippery surfaces for good traction. They have a deep-cut heel that locks onto ladder rungs or stair edges to stabilize the wearer when climbing. Tighten the top using the adjustable strap.

Order your normal boot size unless wearing over large work boots, then order one size up.

Studs dig in and hold tight on icy surfaces.

Ice grippers with heel coverage leave the front of shoes bare, so users can climb ladders safely and operate machinery without damaging the pedals. The adjustable strap secures these grippers to shoes. They have four steel studs on each foot.

Ice grippers with full shoe coverage have studs on the toe and heel to give wearers complete traction for walking.

Slip-on grippers are made of flexible rubber or plastic that stretches to fit over shoes. They have six steel studs or eight tungsten carbide studs on each foot. Grippers with tungsten carbide studs are more durable and harder to dull than those with steel studs. They also give you more stability because they have a greater number of studs. If one of the studs breaks or goes missing, there’s a replacement stud built into the upper toe area for a quick swap. To help you handle thick snow conditions, these grippers have treaded soles for extra traction. They remain elastic even in cold temperatures, so you can stretch them over shoes using their pull tabs without cracking or breaking them.

Grippers with hook and loop straps provide a snug fit over shoes or bulky boots. They have 15 steel studs on each foot to provide better traction than slip-on grippers. Studs are replaceable.

When ordering ice grippers, order your normal shoe size.

Repair rips, split seams, and detached soles to stop leaks in shoes, boots, and waders. These polyurethane adhesives create a strong, flexible seal that keeps water out, so they’re also used to coat seams. Use on leather, plastic, and rubber. They fully harden in 10 hours and dry clear.

These waders go up to your chest to keep you dry in deep water, mud, and sludge. They have adjustable suspenders to modify the fit. All waders fit over socks.

PVC is oil resistant. Blended rubber is more abrasion resistant than PVC. These waders have a layer of foam insulation to keep you warm in cold conditions.

Waders with a safety toe meet ASTM F2413 standards for protection against impact and compression.

Waders with a shank provide arch support by distributing weight during strenuous work, such as climbing ladders.

Waders with a reinforced midsole protect against punctures when working around sharp objects, such as glass, nails, and scrap metal.

Inner and outer seam lengths are approximate. The outer seam length is measured from the bottom of the heel to the top of the wader.

Use these waders to stay dry when you’re in deep water, mud, and sludge. Straps are adjustable to modify the fit; loop through your belt and secure with a snap. All waders fit over socks.

PVC is oil resistant. Blended rubber is more abrasion resistant than PVC.

Waders with a safety toe meet ASTM F2413 standards for protection against impact and compression.

Waders with a shank provide arch support by distributing weight during strenuous work, such as climbing ladders.

Waders with a reinforced midsole protect against punctures when working around sharp objects, such as glass, nails, and scrap metal.

Inner and outer seam lengths are approximate and measured from the bottom of the heel to the top of the wader.

The metal spikes on the bottom of these shoe covers prevent damage to the finish of self-leveling coatings as well as your shoes. Spikes are small enough that coatings can fill in the holes they make when you walk away, so they are level when they cure. Covers fit most shoe sizes.