Often used for climbing electrical substations and utility towers, these kits function as a fall-arrest system during initial ascent and descent. One carabiner connects the 16-ft. anchor span rope to the climbing hook, and the other carabiner connects the rope grab to your harness. Hand tighten the included wing nut on the fiberglass pole (sold separately) to easily attach it to the climbing hook. Then, use the pole to place the hook, which is specially shaped to fit over angle iron, securely above you. The hook serves as an anchor point while climbing.

For adequate fall clearance, you must have at least 18 1/2 ft. of clearance. Use in conjunction with a harness for a complete fall-arrest system. When used properly, the system meets applicable OSHA requirements.

Polyester/elastomer lanyards expand and contract with your movements.

Hook-over lanyards have a large snap hook that attaches directly to a rated structure such as a scaffold or pipe to create an anchor point.

Wraparound lanyards loop around a rated structure such as an I-beam and then attach to themselves to create an anchor point.

A quick-stop lanyard must be used when you have less than 18 1/2 ft. of fall clearance as it will stop your fall within a few inches. Use in conjunction with a harness and an anchor for a complete fall-arrest system. When used properly, the system meets applicable OSHA requirements.

Single-leg lanyards require a carabiner to connect to a harness.

Dual-leg lanyard attaches to two anchors at once.

Use the shock-absorbing attachment (sold separately) to increase the capacity of 310-lb. polyester lanyards to 400 lbs.

Made of steel, these durable lanyards hold up in abrasive and high-heat applications. Attach the large snap hook directly to a rated structure such as a scaffold or pipe to create an anchor point. For adequate fall clearance, you must have at least 20 ft. of clearance. Use in conjunction with a harness for a complete fall-arrest system. When used properly, the system meets applicable OSHA requirements.

Made of Kevlar, these lanyards meet ASTM F887 when used with an arc flash-resistant harness. Wrap the lanyard around a rated structure such as an I-beam and then attach it to itself to create an anchor point. For adequate fall clearance, you must have at least 18 1/2 ft. of clearance. Use in conjunction with a harness for a complete fall-arrest system.

For adequate fall clearance, you must have at least 18 1/2 ft. of clearance. Use in conjunction with a harness and an anchor for a complete fall-arrest system. When used properly, the system meets applicable OSHA requirements.

Polyester/elastomer lanyards expand and contract with your movements.

Dual-leg lanyards attach to two anchors at once.

Made of steel, these durable lanyards hold up in abrasive and high-heat applications. For adequate fall clearance, you must have at least 20 ft. of clearance. Use in conjunction with a harness and an anchor for a complete fall-arrest system. When used properly, the system meets applicable OSHA requirements.

Dual-leg lanyard attaches to two anchors at once.

Made of Kevlar, these lanyards meet ASTM F887 when used with an arc flash-resistant harness. For adequate fall clearance, you must have at least 18 1/2 ft. of clearance. Use in conjunction with a harness and an anchor for a complete fall-arrest system. When used properly, the system meets applicable OSHA requirements.

Dual-leg lanyard attaches to two anchors at once.

These lanyards form their own anchor point by attaching directly to a rated structure. A quick-stop lanyard must be used when you have less than 18 1/2 ft. of fall clearance. Use in conjunction with a harness for a complete fall-arrest system. When used properly, the system meets applicable OSHA requirements.

Hook-over lanyard has a large snap hook that attaches directly to a rated structure such as a scaffold or pipe to create an anchor point.

Wraparound lanyard loops around a rated structure such as an I-beam and then attaches to itself to create an anchor point.

With D-rings on the shoulders, these harnesses allow you to raise and lower workers. They have a D-ring on the back that attaches to a lanyard. A complete fall-arrest system requires a lanyard, a harness, and an anchor. When used properly, the system meets applicable OSHA requirements.

These harnesses have leather-insulated metal components and meet ASTM F887 when used with an arc flash-resistant lanyard. They have a D-ring on the back that attaches to a lanyard. A complete fall-arrest system requires a lanyard, a harness, and an anchor. When used properly, the system meets applicable OSHA requirements.

D-rings on each hip provide a stable working position. Harnesses have a D-ring on the back that attaches to a lanyard for fall protection. A complete fall-arrest system requires a lanyard, a harness, and an anchor. When used properly, the system meets applicable OSHA requirements.

Polyester/elastomer harnesses expand and contract with your movements.

Made of heat-resistant Nomex, these harnesses withstand temperatures up to 700° F. They have a D-ring on the back that attaches to a lanyard. A complete fall-arrest system requires a lanyard, a harness, and an anchor. When used properly, the system meets applicable OSHA requirements.

Harnesses have a D-ring that attaches to a lanyard. A complete fall-arrest system requires a lanyard, a harness, and an anchor. When used properly, the system meets applicable OSHA requirements.

Polyester/elastomer harnesses expand and contract with your movements.