The insulated housing reduces vibration and won’t transmit cold air to the operator’s hand.

Operate in a horizontal position, vertical position, or any angle in between.

These rubber blocks sand flat surfaces.

Blocks hold an adhesive-back sanding roll—cut off worn abrasive and pull out more as needed.

Press onto a compatible sanding tool or backup pad; peel off to remove.

The cushioned construction gives you more control over sanding pressure, creating finer and more consistent finishes.

The premium abrasive stays sharp longer.

Holes allow dust removal when used with a vacuum sander.

The premium abrasive lasts longer as well as cuts faster and produces a more consistent finish than standard hook and loop discs.

The mesh backing lets sanding dust and debris escape during use, preventing material build up on the abrasive surface.

The thick, abrasive-embedded nylon mesh construction gives you maximum control over sanding pressure.

These discs are abrasive-embedded cloth with a cushioned layer.

The premium abrasive lasts longer as well as cuts faster and produces a more consistent finish than standard hook and loop discs.

The cushioned construction gives you more control over sanding pressure, creating finer and more consistent finishes.

A special fastener on the back of these discs allows you to easily swap one disc for another.

These discs have a harder abrasive than standard quick-change discs.

The outer 3/8" of these discs is extremely flexible to prevent marring or gouging your work when sanding a radius or contour.

Thicker, more pliable, and less aggressive than standard nylon mesh quick-change discs, use these for finer sanding on curved surfaces.

The abrasive-embedded nylon mesh construction gives you more control over sanding pressure.

The premium abrasive stays sharp longer.

The heavy duty construction provides more support than standard discs for heavy material removal.

The premium abrasive stays sharp longer.

The premium abrasive stays sharp longer. Holes in the disc let you see the surface you’re sanding.

The premium abrasive stays sharp longer.

Fit these discs over your tool’s arbor.

A coating prevents dust and debris from building up on the abrasive surface.

With more flaps than standard discs, these last 30-40% longer.

With more flaps than standard discs, these last 30-40% longer.

A heavy duty backing plate provides more support than standard discs for heavy material removal.

The flaps alternate between an abrasive to remove material and a lubricant that minimizes heat to reduce discoloration of the work surface.

These discs have a harder abrasive than standard flap sanding discs for corners.

With more flaps than standard discs, these last 30-40% longer.

The backing plate on these discs can be sheared away as the abrasive flaps wear down, allowing you to use more of the disc rather than replacing with a new one.

The flaps wrap around the outer edge of these discs to sand welds at right angles.

A coating prevents dust and debris from building up on the abrasive surface.

These belts resist deterioration when used with water or cutting fluids.

The widely spaced grains prevent dust and debris from building up on the abrasive surface.

These belts have a cushioned layer.

Use these narrow belts on hand-held sanding sticks.

These belts have a tear-resistant backing.

Secure the shank into the collet or chuck of your tool.

The flaps are slit into narrow strips to provide more flexibility than other flap wheels.

A coating prevents dust and debris from building up on the abrasive surface.

With alternating cloth and nylon mesh abrasive flaps, these wheels are more flexible and produce finer finishes than all-cloth flap sanding wheels.

The premium abrasive stays sharp longer.

These assortments include various sizes and grits of flap sanding wheels. The threaded stud allows faster wheel changes but requires the use of an adapter in your tool.

Polish, clean, and debur deep inside tubes and cylinders.

Shape, debur, and sand edges and internal surfaces.

The abrasive-embedded mesh construction gives you more control over sanding pressure, creating finer and more consistent finishes.

Create smooth finishes on wood.

These rolls can be cut to length.

The soft abrasive is good for fine hand-polishing of soft nonferrous metals. Also known as crocus cloth.

These cut-to-length rolls resist deterioration when used wet or with grease, chemicals, cutting fluids, and other solvents that may be present when sanding.

Flexible enough to sand around curves and in corners, these sponges provide the comfort and control of a sanding block.

These sponges conform exceptionally well to small, contoured surfaces.

The dental floss of abrasives, these cords slip into areas that other forms cannot. They're good for deburring and polishing small holes, narrow slots, keyways, and grooves.

Providing the control of a sanding block while remaining flexible, these sponges sand around curves and in corners.

Create consistent finishes on stainless steel, titanium, steel, iron, and nickel.

Quickly attach, remove, and reuse.

A coating prevents dust and debris from building up on the abrasive surface.