For Load Direction For Load Direction |
|---|
 | Combined Radial and Thrust |
 | Radial |
 | Thrust |
Roller Style Roller Style |
|---|
 |  |
| Shaft Mount | Threaded Stud |
Environment Environment |
|---|
Dynamic Radial Load Capacity Dynamic Radial Load Capacity |
|---|
|
|
Static Radial Load Capacity Static Radial Load Capacity |
|---|
|
|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
|---|
|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
|---|
|
Specifications Met Specifications Met |
|---|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
|---|
Shoulder Style Shoulder Style |
|---|
|
About Track Rollers
Also known as cam followers, track rollers have a thick outer roller that runs directly on a flat surface.
More
Sanitary Shaft-Mount V-Groove Track Rollers
Support and guide loads on angle rails in food, pharmaceutical, and other sanitary environments. Also known as yoke-style cam followers, these track rollers offer more mounting flexibility than threaded alternatives and are typically mounted on shafts and clevis rod ends. They’re permanently lubricated to prevent contamination, with sealed and shielded bearings blocking out debris and liquids to protect the lubricant. FDA compliant and NSF registered H1, the lubricant is safe for incidental contact with food. These track rollers are made of stainless steel, so they won’t corrode from frequent washdowns with harsh cleaners.
Double-sealed rollers are better protected from high-pressure liquid and debris than single-sealed rollers, and also operate within a broader temperature range. They’re built to withstand the frequent high-pressure, high-temperature washdowns found in food and pharmaceutical plants.
For technical drawings and 3-D models, click on a part number.
Roller | Groove | Radial Load Capacity, lbs. | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Diameter | Width | For Shaft Diameter | Overall Width | Width | Depth | Maximum Speed, rpm | Static | Dynamic | Static Thrust Load Capacity, lbs. | Maximum Temperature, °F | Bearing Type | Specifications Met | Each | |
440C Stainless Steel V-Groove Rollers With Seal | ||||||||||||||
Single-Sealed and Shielded | ||||||||||||||
| 1 3/16" | 7/16" | 3/8" | 7/16" | 1/4" | 3/16" | 3,400 | 590 | 590 | 140 | 175° | Ball | FDA Compliant 21 CFR 178.3570, NSF Registered H1 | 0000000 | 0000000 |
| 1 13/16" | 5/8" | 15/32" | 5/8" | 5/16" | 5/16" | 2,200 | 1,300 | 1,300 | 380 | 175° | Ball | FDA Compliant 21 CFR 178.3570, NSF Registered H1 | 0000000 | 000000 |
Double-Sealed and Shielded | ||||||||||||||
| 1 3/16" | 7/16" | 3/8" | 7/16" | 1/4" | 3/16" | 3,400 | 540 | 540 | 90 | 210° | Ball | FDA Compliant 21 CFR 178.3570, NSF Registered H1 | 0000000 | 000000 |
| 1 13/16" | 5/8" | 15/32" | 5/8" | 5/16" | 5/16" | 2,200 | 1,100 | 1,100 | 130 | 210° | Ball | FDA Compliant 21 CFR 178.3570, NSF Registered H1 | 0000000 | 000000 |
Sanitary Threaded V-Groove Track Rollers
Guide loads along angle rail tracks in food and pharmaceutical plants or other sanitary environments with these threaded rollers. They’re permanently lubricated, a feature often seen in sanitary areas where repeated lubrication could cause contamination. Their lubricant is NSF registered H1 as safe for incidental contact with food. They’re made of stainless steel, so they won’t corrode from frequent washdowns with harsh cleaners. The bearings are sealed and shielded to keep out liquid and make sure the lubricant stays intact. These rollers have a V-groove profile, which allows debris to fall off when they’re mounted on angle rails. They’re also known as cam followers.
Rollers with a standard shoulder have a threaded mounting stud. Thread them directly into a component, or secure them with a nut for through-hole mounting.
Rollers with an adjustable shoulder are also known as eccentric track rollers. They can be moved up and down, and they’re commonly used alongside standard rollers to correct misalignment. Secure them with a nut for through-hole mounting.
For technical drawings and 3-D models, click on a part number.
Roller, mm | Stud, mm | Thread | Groove, mm | Radial Load Cap., lbs. | ||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Dia. | Wd. | Dia. | Lg. | Size | Pitch, mm | Lg., mm | Shoulder Lg., mm | Hex Shoulder Wd., mm | Ht. Adjustment Capability, mm | Wd. | Dp. | Max. Speed, rpm | Static | Dynamic | Static Thrust Load Cap., lbs. | Max. Temp., °F | Bearing Type | Includes | Each | |
Single-Sealed 440C Stainless Steel V-Groove Rollers | ||||||||||||||||||||
Standard Shoulder | ||||||||||||||||||||
| 31 | 11 | 10 | 25 | M10 | 1.5 | 15 | 3.1 | 14 | 1 | 6 | 3 | 3,400 | 590 | 590 | 140 | 175° | Ball | Mounting Hardware | 0000000 | 0000000 |
| 46 | 16 | 12 | 30 | M12 | 1.75 | 18 | 4.1 | 19 | 1.5 | 8 | 4 | 2,200 | 1,300 | 1,300 | 380 | 175° | Ball | Mounting Hardware | 0000000 | 000000 |
Adjustable Shoulder | ||||||||||||||||||||
| 31 | 11 | 10 | 25 | M10 | 1.5 | 15 | 3.1 | 14 | 1 | 6 | 3 | 3,400 | 590 | 590 | 140 | 175° | Ball | Mounting Hardware | 0000000 | 000000 |
| 46 | 16 | 12 | 30 | M12 | 1.75 | 18 | 4.1 | 19 | 1.5 | 8 | 4 | 2,200 | 1,300 | 1,300 | 380 | 175° | Ball | Mounting Hardware | 0000000 | 000000 |