We will reply to your message within an hour.
Housing is plastic.
Housing is brass.
These gauges come with a calibration certificate traceable to NIST that states they've passed a test for accuracy.
Measure tension force as well as weight.
The large dial makes these gauges easy to read. They measure tension force as well as weight.
Press the side of the gauge tip against an object to record the amount of tension required to move it.
Measure the tension of wire and filament without pausing your operation.
Apply your load directly to the top of these gauges to measure compression force.
Use the included Windows-compatible software to upload measurement data.
Measure tension force as well as weight. Also known as dynamometers.
Safely view your tension force measurements on a handheld receiver up to 450 ft. away when moving bulk material with cranes and hoists.
Also known as load cells, these sensors measure and track the forces of your equipment by converting them into electrical signals.
Use these gauges with changeable sensors and square-drive sockets to display, collect, and download torque readings.
Place your tool and the included square drive connector on the tester and turn.
These testers have a digital display and are accurate to ±1%.
Measure the force of hand and non-impact electric torque screwdrivers to keep fasteners from failing due to under or overtightening.
Measure the twisting force needed to tighten or loosen caps and knobs with these torque testers.
Calibrate torque-limiting power tools such as air-powered and impact drivers.
Made to last, our most corrosion-resistant rulers are stainless steel and have wear-resistant etched markings.
A calibration certificate traceable to NIST is included with these stainless steel rulers.
Numbers and graduations etched in light colors are easy to see on a black background.
Rulers have large numbers and deeply etched graduations.
Made of aluminum, these rulers are an economical alternative to stainless steel rulers.
Ensure accurate measurements with these certified rulers.
Keep your workpiece in view as you measure with these see-through rulers.
A cork back prevents slipping and protects delicate surfaces.
Made of wood with a clear protective coating, this ruler is an economical choice for measuring objects up to three feet long.
A clear protective coating and brass endcaps add durability to these hard-maple rulers.
Also known as machinists’ rules, these rulers ensure reliable, repeatable measurements.
Ensure reliable, repeatable measurements with these rulers.
An economical alternative to Starrett High-Accuracy Rulers, these provide reliable, repeatable measurements.
These rulers include a certificate of calibration traceable to NIST with test measurements that confirm accuracy.
A reversible, removable hook grabs the edge of an object for easy alignment.
Protect your ruler from scratches and wear with a TiN (titanium nitride) coating.
High-powered magnets hold these rulers in place.
Permanently mount these rulers to a machine or workbench.
Use to find diameters and centers.
Rulers are narrow and just 6" long to measure in tight spaces.
Create a ruler up to 192" long by adding continuous segments.
Fold these rulers for convenient storage and transport.
A safety guard or finger groove prevents your fingers from getting in the way as you cut with these rulers.
Permanently mount these rulers on machines, tanks, and walls to measure heights and depths.
The graduations on these rulers are half the actual length of the object you are measuring.
These extra-thick rulers have a polycarbonate coating that resists wear from traffic and chemicals.
Measurements are printed from top to bottom for measuring heights and depths.
Use to measure heights and tank levels.
A hook grabs the edge of an object for easy alignment.
Zero marks the center when these rulers are positioned so the same number touches each side of an object.
Slip these rulers into your pocket, so they’re always on hand to find center readings. All are narrow and about 6" long to measure in tight spaces.
Rulers are marked with picas for working with type.
Slide this ruler across the surface of plans, maps, and blueprints and read the measurement on the digital display in one of 111 different scales including inches, feet, yards, miles, centimeters, meters, kilometers, or a scale you define.
Determine the circumference of a circle without calculations.
Ensure accurate measurements with certified tape measures.
Attach the magnetic-hook tip to metal surfaces to assist vertical and distance measuring.
The blade locks in place when extended until you press the release lever, and a magnetic-hook tip attaches to metal surfaces to assist vertical and distance measuring.
An orange case makes these tape measures easy to spot.
These tape measures have a chrome-plated, impact-resistant plastic case.
A built-in slot for your finger allows you to control the speed these tape measures retract without pinching your finger with the hook.
Drop tested to 120 ft., these tape measures can fall from a 10-story office building and still work.
A black blade with bright yellow graduation marks makes these tape measures easy to read, even in low-light and high-glare locations. Drop-tested to 120 ft., they can fall from a 10-story office building and still work.
A window with an indicator line clearly shows the measurement.
Compared to standard tape measures, these are less than half the size.
The blade on these tape measures is chrome-plated for durability and corrosion resistance.
Slide the lock to hold the blade in place.
Measure from a distance—the blade on these tape measures remains rigid when extended up to 11 feet.
Control how fast the blade retracts without pinching your finger—these tape measures have a built-in finger slot.
The case is impact-resistant plastic that's yellow for high visibility. Slide the lock to hold the blade in place.
The blade automatically locks in place when extended and stays locked until you press the release lever.
All internal parts, including the blade, are stainless steel for corrosion resistance.
For a comfortable and secure hold, these tape measures have a narrow case with a molded rubber grip.
Numbers and graduation marks are printed vertically to measure heights and depths.
Fractions are labeled on the blade every 1/8" for fast reading.
Pull the blade out of these tape measures and it locks in place automatically. Press the lever to release it.
With a built-in slot for your finger, you can control the speed these tape measures retract without pinching your finger with the hook.
Read measurements in dark spaces with the LED light that illuminates the blade.
Attach to curved or flat steel surfaces.
Durable and flexible, these tape measures are coated for scratch resistance.
At about half the size of standard diameter tape measures, these fit in your pocket.
Also known as tree tapes, wrap these tape measures around circular items to determine diameter and measure circumference without the need for calculations.
Accurately measure diameter.
Also known as tree tapes, wrap these tape measures around circular items to measure the circumference and determine the diameter without any calculations. The blade automatically retracts unless it’s looped onto something or the lock is engaged.
Measure distances over 35 ft.
Hold on to the large, rubber-coated handle while carrying these tape measures.
These reliable tape measures include a calibration certificate traceable to NIST stating they have passed a test for accuracy.
Measure over 35 ft. and quickly retract the tape once you're finished. These tape measures will recoil automatically unless you engage the brake or hook the tip onto something.
Grip the tape measure through the hole in the center and quickly rewind the blade with the specially designed reel.
Easily spot the brightly colored case on these tape measures around your worksite and in your toolbox.
Find the exact center of your work. Measure the total distance with the upper scale; then find the same number on the bottom scale—that's your center point.
Measure volume in gallons or liters without calculations.
Built to resist corrosion and last in harsh environments, these vertical rulers are iron with a porcelain-enamel finish. Mount them to walls and tanks.
Permanently mount these vertical rulers to walls and tanks.
Connect continuous segments to create a ruler up to 10 ft. long.
Fold these vertical rulers for convenient storage and transport.
Attach a plumb bob (sold separately) to the rope’s hook and lower it into your tank to take a measurement.
Also known as oil-gauging tapes, use these tape measures to check the level of oil and other fluids in deep, large containers such as tanks and vats.
Reach deep into small holes and slots for precise depth measurements.
Take precise depth measurements in small holes and slots.
All gauges have zero-position memory, also known as absolute (ABS) positioning, which retains the measuring position when the gauge is turned off.
Connectable extension rods allow you to measure depths.
Measure depth in dusty or wet environments--these gauges are rated IP67 for protection from dust and temporary water submersion.
Check measurements at a glance.
Use these blades with Starrett High-Accuracy Combination Square Heads. They meet Fed. Spec. GGG-R-791H, which establishes uniform standards for accuracy, graduations, and size.
Replace your try square, miter square, depth gauge, height gauge, center-point finder, and level. The blade on these squares meets Fed. Spec. GGG-R-791H, which establishes uniform standards for accuracy, graduations, and size.
Replace your try square, miter square, depth gauge, marking gauge, 90° level, ruler, and scriber with one tool.
Blades are for use with High-Accuracy Combination Square Heads.
Use these squares in place of your try square, miter square, depth gauge, height gauge, center-point finder, and level.
A titanium coating protects the blade against scratches and wear.
Built for welding and other heavy duty fabricating jobs, these squares have an extra-wide head and a large thumbwheel, so they’re easy to adjust and hold while wearing gloves. They combine the functionality of a try square, miter square, depth gauge, marking gauge, 90° level, and ruler in one tool.
Ensure reliable, repeatable angles.
Also known as carpenters’ and framing squares, these have graduations on both blades for horizontal and vertical measurements.
Also known as try squares, these are square inside and out for checking and marking angles.
These squares meet Fed. Spec. GGG-S-656-E, which establishes uniform standards for square accuracy to ensure reliable, repeatable angles.
Measure and mark material exactly where you need to with a sliding blade.
Large numbers and dark graduations on both blades make it easy to read horizontal and vertical measurements.
Also known as rafter squares, these have a 0° to 90° scale for measuring angles.
Pipe fitting sizes and welding charts are shown on this square in wear-resistant etched markings.
Mount on any flat surface.
Measure angles with these round protractors.
Measure the outside diameter of small round- and hex-shaped objects such as rods, drill bits, bolts, and tubing with this pocket-size tool.
Wrap these pocket-size tape measures around pipe and fittings to determine size.
Measure outer diameter and mark lines around pipe.
Also known as safety scales, these gauges confirm that the gaps between the grinding wheel and the tool rest and tongue comply with OSHA and ANSI requirements.
Verify machine guard openings are sized to prevent hands and fingers from reaching hazards. These gauges check whether a machine guard complies withOSHA, CSA, or ANSI requirements.
Lightweight yet strong and durable, these bamboo levels won't stick to wet cement. Also known as masonry levels.
The sturdy box-style housing has precision-machined leveling surfaces to ensure accuracy.
These brightly-colored levels are easy to spot.
One of the horizontal vials is a pitch gauge that reads slope in 1/8" increments.
Glow-in-the-dark vials are easy to read in low light.
Align and measure at the same time with these levels that have rulers on the front and side.
Adjust a surface into a level position on multiple planes.
These levels have a plastic housing.
These levels have a sturdy aluminum housing.
These levels come with a calibration certificate that's traceable to NIST and includes the test measurements that confirm accuracy.
A color LCD and highly accurate sensor allow you to level both horizontally and vertically at the same time. This level also displays a real-time vibration graph.
A color LCD and highly accurate sensor allow you to level both horizontally and vertically at the same time.
With a precision-machined leveling surface and highly sensitive vial, this level provides superior accuracy.
These levels come with a calibration certificate traceable to NIST that states they've passed a test for accuracy.
Slip these levels into a drilled hole.
Mount these levels to a table or other horizontal surface and they will indicate when you're level on the horizontal plane.
Mount these levels to a wall or other vertical surface and they will indicate when you're level on the horizontal plane.
Stick these levels onto carts, mobile equipment, and other horizontal surfaces to make sure they're level before use. The adhesive backing forms a permanent hold with no drilling or fasteners required.
Replace broken vials in tools and equipment.
A magnet keeps this 90° level in place while you position posts and corners.
Use this 90° level to position posts and corners.
A thumb screw secures to the end of your pipe or conduit to ensure accuracy when bending.
Hang these levels from the center of a string stretched between two points, and the string acts as a horizontal reference line.
One person is all you need to determine level around corners and over long distances.
Level machinery, check surface flatness, and scribe work positions.
Take measurements off of scaled architectural or engineering drawings with these specialized scales.
Unfold and lock the corners to form a triangle for marking angles.
A protractor and triangle in one, use these tools to quickly set any angle from 0° to 90°.
Mark and cut straight lines or 90° angles.
Use these highly accurate straightedges as a guide to scribe and cut straight lines and to check surface straightness.
Small enough to fit into your pocket, the blade is narrow and only 6" long. These scales are often used for taking measurements off scaled architectural or engineering drawings.
A rule, compass, protractor, and template all in one tool.
Draw and cut straight lines in drafting, graphics, and construction applications.
Highly accurate, these straightedges work as a guide to scribe and cut straight lines and to check surface straightness. They have graduations, so you can take measurements as you go.
Compare your surface finish to one of the swatches on these solid nickel-alloy scales.
These scales come with a calibration certificate traceable to NIST that states they've passed a test for accuracy.
Compare your surface finish to one of the swatches on this inexpensive plastic scale.
A microscope measures the indentation made by a small diameter ball penetrator to provide a hardness reading.
Make sure your hardness testers are accurately calibrated.
Operate these testers with one hand. Squeeze the handles until the penetrator contacts the test material and a reading appears on the dial indicator.
These testers use an indenter to measure hardness.
Slide these bars into a Brinell hardness tester to determine the hardness of very hard steel.
Measure the hardness of flat materials, such as plastic, rubber, and laminate.
Determine the relative hardness of resins, film, lacquer, and paint by testing their resistance to scratches by graphite pencils.
One side of these rulers lists tap and drill sizes. The other side has a decimal equivalent table and a 6" rule.