Also known as press screws, mount these clamps through a drilled hole and turn the crank to move the jaw end of the screw in and out.

The contact area is covered in plastic to protect soft metal and polished surfaces. Attach these tips to the end of a screw or threaded stud to apply uniform pressure on uneven and angled surfaces. Also known as toggle and swivel-foot pads.

When loosened, you can spin the body of this clamp around its mounting point for better access to the workpiece.

With five times the capacity of standard C-clamps, these are the highest capacity clamps we offer.

These clamps are made of stainless steel for excellent corrosion resistance.

Made entirely of fiberglass, these clamps won’t transmit electricity and are chemical resistant. They're often used around electrical equipment as well as in plating and anodizing applications.

All components of these clamps are made of aluminum-bronze that is Factory Mutual approved. They satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

With no handle or protruding screw, these clamps can fit into tight spaces.

Clamp farther in from the edge of a workpiece than with other C-clamps.

Hold the workpiece down against a bench or table.

Plastic clamping surfaces prevent damage to material.

Reduce the chance of getting pinched when unclamping. These clamps have more space between the handle and the arm than other low-profile toggle clamps.

Hold workpieces of different thicknesses without adjustment.

Weld these clamps to the side of an object or drill your own holes in the mounting plate and bolt into place.

Push the lever to lock the handle and prevent accidental opening.

A nonreflective black oxide finish prevents glare that can interfere with machine vision systems.

Two sets of mounting holes allow mounting on the bottom or side.

The mounting base secures these clamps to a rail or bar.

Unlike the smooth and flat edges of standard fixture clamps, these clamps have ridges that bite into parts, making them good for gripping castings and rough-cut stock.

Set one of these clamps between two workpieces in a fixture and tighten the screw to push the clamp's sides out for a secure hold.

Machine these fixture clamps to match the contours of your workpiece for a stronger grip.

Tighten the spring-loaded socket head cap screw on these clamps to hold your workpiece from above.

These clamps wedge against the workpiece ID to grip cast, unfinished, or uneven parts, leaving the outside clear for machining.

These clamps have twice the capacity of standard fast-action bar clamps.

Pull the handle to lock the jaw in place and prevent loosening caused by vibration.

Hold up to five times the capacity of standard bar clamps. These are also known as I-beam clamps.

All adjustments can be made from one end, allowing clamping in tight spaces.

Attach to your bar clamp to hold material on three sides.

Each arm slides freely for quick, one-handed positioning. They lock when the screws are tightened onto a workpiece.

Also known as J-clamps, these provide additional clearance to reach around obstructions and clamp workpieces in recessed areas.

Two swivel pads on each jaw pivot to grip nearly any shape of material.

Instead of a step block, support these clamps using a screw, leveling mount, or any other threaded object.

The stepped end provides support and quick height adjustment when paired with a step block.

Get everything needed for basic workholding on a machine table.

Designed to provide more clearance above the nut than standard clamps, these have an offset shape. Also known as gooseneck clamps.

A plastic pad on the gripping surface of these clamps prevents workpiece marring, making them useful for holding polished surfaces and reducing the need for secondary finishing steps.

Unlike other setup clamps that grip the horizontal surface of a workpiece, these clamps have a pivoting ball in the tip to get a firm hold on angled parts.

The built-in T-slot nut on these side clamps lets you clamp a part to a machine table quickly. Their small footprint leaves more free space on your table than standard side clamps.

Each jaw can be positioned at an angle to hold round, angled, and odd-shaped material.

These rugged steel handles provide lasting durability for applications involving frequent positioning, tightening, and holding adjustments. Lift the handle to rotate freely; then release the handle to engage and tighten. These handles are also known as clamping handles.

These rugged steel handles provide lasting durability for applications involving frequent positioning, tightening, and holding adjustments in areas with limited vertical space. Lift the handle to rotate freely; then release the handle to engage and tighten. These handles are also known as clamping handles.

Prevent unintentional changes to equipment settings—when not in use, these handles are disengaged and turn freely. To change the position, push down on the handle and turn. When you release the handle, it disengages once again. These handles are also known as clamping handles.

A soft textured surface provides a comfortable grip for applications involving frequent positioning, tightening, and holding adjustments. Lift the handle to rotate freely; then release the handle to engage and tighten. These handles are also known as clamping handles.

Use these handles for applications involving frequent positioning, tightening, and holding adjustments near food processing lines without the risk of contaminating the food. These handles are also known as clamping handles.

With a minimum surface resistance of 10,000 ohms, these handles reduce static electricity that can damage electronic equipment. Also known as clamping handles, use them for applications involving frequent positioning, tightening, and holding adjustments. Lift the handle to rotate freely; then release the handle to engage and tighten.

Also known as double cams, these complete cam handles have a durable, extra-large handle for clamping on fixture bases, plates, and workpieces. For fast adjustments, push down on the handle and the head applies pressure to quickly draw two parts together.

Use these handles to keep holes aligned or lift several sheets of thin material. They have a plug that expands to grip the edges inside holes. They are not suitable for permanent installation—use only for temporary mounting.

Bonded to the stud is an acrylic adhesive that adds friction to resist loosening from vibration. Use these knobs to position, tighten, and hold fixtures, equipment, and machinery. They mount into a threaded hole.

Identify equipment controls and components at a glance by their color. Mount these knobs into a threaded hole. They provide a secure grip to position, tighten, and hold fixtures, equipment, and machinery.

Never lose these knobs—tether them to equipment to keep them where you need them. They provide a secure grip to position, tighten, and hold fixtures, equipment, and machinery. Mount them into a threaded hole.

Knobs have left-hand threads; they're used in applications where counterclockwise motion can loosen common right-hand threads. Mount them into a threaded hole to position, tighten, and hold fixtures, equipment, and machinery.

Long shafts can thread through these knobs for mounting versatility. The knobs provide a secure grip to position, tighten, and hold fixtures, equipment, and machinery.

Like locknuts, these knobs have a nylon insert that grips threads to resist loosening. Long shafts can thread through these knobs for mounting versatility. Use the knobs as a grip to position, tighten, and hold fixtures, equipment, and machinery.

A rubber coating provides a comfortable grip to position, tighten, and hold fixtures, equipment, and machinery. Long shafts can thread through these knobs for mounting versatility.

Install these knobs on a threaded stud. They provide a secure grip to position, tighten, and hold fixtures, equipment, and machinery.

The domed top allows you to firmly hold these knobs in the palm of your hand to position, tighten, and hold fixtures, equipment, and machinery. Install these knobs on a threaded stud.

Designed for sanitary environments, these knobs are commonly used in pharmaceutical and food-processing facilities. Install them on threaded studs to position, tighten, and hold equipment.

Mill specific holes or keyways in the hub to meet your specifications, or weld in place. These knobs provide a secure grip to position, tighten, and hold fixtures, equipment, and machinery.

The domed top allows you to firmly hold these knobs in the palm of your hand. Mill specific holes or keyways in the hub to meet your specifications, or weld in place. Use these knobs to position, tighten, and hold fixtures, equipment, and machinery.

Create custom threads or secure with a set screw to provide a firm grip to position, tighten, and hold fixtures, equipment, and machinery. Long shafts can pass through these knobs for mounting versatility.

Mill specific holes or keyways in the hub to meet your specifications or weld in place. Insert a bar between the arms and twist. The bar provides maximum leverage to tighten knobs securely.

Control devices with round or D-shaped shafts and view settings at a glance with a pointer.

A rubber coating or construction provides a comfortable grip. Use these knobs to control devices with round or D-shaped shafts and view settings at a glance with a pointer.

Expose these easy-to-grip ball knobs to light and they will glow green in the dark. Use them on control levers, push-pull rods, and emergency release handles. They mount on a threaded stud.

Mount these oval, easy-to-grip ball knobs on a threaded stud. They're good for control levers and push-pull rods.

With a mounting hole center-to-center distance of 1" or less, these are the smallest pull handles we offer. Thread screws through holes from the back of your surface into the handles to open and close tiny doors and drawers.

Designed to meet DIN EN 61340-5-1, these handles reduce static electricity that can damage electronic equipment. Fasten them directly to the front of your surface to open and close a variety of doors and drawers.

Suitable for use with food-processing equipment, these handles are made of FDA listed materials.

Cut the grip to the length you need before mounting. Fasten these handles directly to the front of your surface to open and close a variety of doors and drawers, including those on furniture, machines, and equipment.

Thread screws through holes from the back of your surface into the handles to open and close a variety of doors and drawers, including those on furniture, machines, and equipment.

For applications that require a large gripping area, these handles have a center-to-center distance of 12" or more. Fasten them directly to the front of your surface to open and close a variety of doors and drawers, including those on furniture, machines, and equipment.