Made from brass, these inserts are electrically conductive, nonmagnetic, and have good corrosion resistance.

These aluminum inserts are 70% lighter than brass inserts, electrically conductive, and nonmagnetic. They have good corrosion resistance, which is comparable to brass but not as good as stainless steel.

These 18-8 stainless steel inserts have better corrosion resistance than brass inserts and may be mildly magnetic.

The flange keeps these inserts from pulling through a hole. Press them in from the underside of material, and install a screw from the top of material.

The barbed sides keep these securely in place even before a screw is installed.

70% lighter than stainless steel, these aluminum inserts are mildly corrosion resistant and nonmagnetic.

Install these inserts into plastic parts to create a secure base for fasteners.

The tapered shape makes it easier to guide these inserts into a hole during installation. Use a drill bit to create a straight hole, then taper the top half.

These 18-8 stainless steel inserts have excellent resistance to chemicals and may be mildly magnetic.

Steel inserts have high strength for durability.

The flange keeps these inserts from being pulled through a hole and provides a load bearing surface.

Steel inserts have high strength for durability.

These 18-8 stainless steel tee nut inserts have better corrosion resistance than zinc-plated steel tee nut inserts.

Fewer prongs than other tee nut inserts reduce the risk of splitting hardwood—these inserts have three short prongs.

Hooked prongs give these inserts excellent holding power even when removing screws.

Mount these inserts flush or below the material's surface.

A closed end seals out elements and protects the threads on these inserts from debris.

A black-phosphate finish provides mild corrosion resistance.

These inserts are the most corrosion-resistant thread-locking inserts we offer.

Adhesive on both the internal and external threads keeps these inserts in place and holds screws tight.

Eliminating the need for primer, these inserts are coated to resist corrosion when installed in different materials.

These inserts have a high strength-to-weight ratio and resist acids and salt water better than nickel alloy and stainless steel inserts.

A distorted thread grips the screw to resist loosening.

A dry film keeps the screw from sticking or binding in these inserts during installation.

Assortments include various sizes of helical inserts and a tap, a drill bit, and an installation tool for each thread size.

A dry film keeps the screw from sticking or binding in these inserts during installation.

These kits have short-, normal-, and long-reach inserts, an installation tool, and a tap.

Made of 18-8 stainless steel, these inserts have good corrosion resistance.

The strongest key-locking inserts we offer, these inserts are made to stringent military specifications.

Forming the strongest hold of any of our threaded inserts, these inserts have a distorted internal thread to lock screws into place and keys that drive into surrounding material to prevent slipping and rotating.

Press these inserts into a drilled hole and the flexible metal teeth anchor them in the material. Use them with carbon fiber, fiberglass, and garolite.

The most corrosion resistant twist-resistant rivet nuts we offer, these stand up to chemicals.

These aluminum rivet nuts are one-third the weight of steel rivet nuts and have mild corrosion resistance.

Wedges under the flange lock the nut in place in soft materials such as brass and aluminum.

These rivet nuts are mildly corrosion resistant.

These kits include one size of low-profile rivet nuts.

The most corrosion resistant low-profile rivet nuts we offer, these stand up to chemicals.

A nonconductive rubber coating insulates the nut from electricity, seals out moisture, and damps vibration.

These aluminum rivet nuts are one-third the weight of steel rivet nuts and have mild corrosion resistance.

Threads float inside the nut so you can install a screw at a slight angle to align with off-center parts. They’re also known as Riv-Float nuts.

Projections on the base concentrate the weld and provide room for heat to dissipate.

Weld these nuts to stainless steel surfaces.

Weld these nuts to stainless steel surfaces.

These nuts can be used in channels and tight spaces where round-base weld nuts won't fit.

A smooth base on these metric nuts provides more contact with the mating surface than weld nuts with projections

Projections on the base concentrate the weld and provide room for heat to dissipate.

You can weld these nuts to flat and uneven uncoated stainless steel surfaces for a strong permanent hold.

Weld these nuts to flat and uneven uncoated steel surfaces for a strong permanent hold.

Threads float inside the retainer so you can install a bolt at a slight angle to align with off center parts.

These nuts have three mounting holes to accept screws and rivets for use with thin materials.

These adhesive-mount nuts have a zinc plating for corrosion resistance in wet environments.

These nylon nuts are chemical resistant, nonconductive, and lightweight.

Also known as clinch style captive nuts, press these nuts into a drilled or punched hole with an arbor press or similar pressure tool.

These nuts have good chemical resistance and may be mildly magnetic.

A flat hex head sits flush against the material surface for use in low-clearance applications.

Stainless steel press-fit nuts have excellent corrosion resistance in most environments.

Also known as broach style captive nuts, these nuts have good chemical resistance and may be mildly magnetic.

These press-fit nuts are tin plated to resist corrosion from chemicals and salt water.

Stainless steel nuts have excellent corrosion resistance in most environments.

About half the strength of medium-strength steel coupling nuts, these metric nuts are for light duty fastening applications.

Also known as G-style clip on nuts, slide these nuts on the edge of a panel and position them by hand.

Also known as U-style clip on nuts, these nuts have a barrel with multiple threads for secure thread engagement.

A hex-shaped barrel allows these clip-on nuts to be gripped with a wrench to hold them in place when tightening a screw. They have multiple threads for more thread engagement than low-profile clip-on nuts.

These nuts firmly clip onto the edge of panels and stay secure.

The S-style design provides more strength than other no-slip clip-on nuts.

A ribbed-shaped body holds the nut in place so it won't move when tightening a screw. Assortments contain rivet nuts, mandrels, nosepieces, and a plier-style installation tool.

Often referred to as four-way expansion anchors, these expand in four directions to resist loosening from vibration.

Also known as double expansion anchors, these expand from both sides for full contact and a secure hold.

More corrosion resistant than 18-8 stainless steel anchors, these 316 stainless steel anchors have excellent resistance to chemicals and salt water.

A zinc plating provides corrosion resistance in wet environments.

Also known as lag shields, these anchors are designed for use with large-diameter wood screws.

Also known as mungo anchors, these have large fins that prevent rotation.

Use with any type of sheet metal or wood screw.

For narrow holes and small cavities where toggle anchors won't fit.

Fins prevent these anchors from spinning during installation.

A drilled hole is required for installation.