System of Measurement System of Measurement |
|---|
|
Head Type Head Type |
|---|
 | Flat |
Finish Finish | Show |
|---|
|
Finish Finish | Hide |
|---|
Drive Style Drive Style |
|---|
 | Phillips |
For Use With (Electrical) For Use With (Electrical) |
|---|
|
Tip Type Tip Type |
|---|
 | Pointed |
Number of Panel Cutouts Number of Panel Cutouts |
|---|
|
Connection End Connection End |
|---|
|
Mount Type Mount Type |
|---|
|
Installation Installation |
|---|
|
For Use In For Use In |
|---|
|
About Tapping Screws
More
Steel Phillips Flat Head Screws for Sheet Metal
These steel screws are available with corrosion-resistant finishes. They're beveled under the head for use in countersunk holes. Screws penetrate 0.025" and thinner sheet metal. Length is measured from the top of the head.
Nickel-plated steel screws have a decorative finish and are more corrosion resistant than zinc-plated screws.
For technical drawings and 3-D models, click on a part number.
Head | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| Lg. | Flat Head Profile | Dia. | Ht. | Drive Size | Drill Bit Size | Approximate Threads per Inch | Pkg. Qty. | Pkg. | |
No. 4 | |||||||||
| 1/2" | Standard | 0.212" | 0.067" | No. 1 | No. 44 | 24 | 25 | 000000000 | 000000 |
| 5/8" | Standard | 0.212" | 0.067" | No. 1 | No. 44 | 24 | 25 | 000000000 | 00000 |
| 3/4" | Standard | 0.212" | 0.067" | No. 1 | No. 44 | 24 | 25 | 000000000 | 00000 |
No. 5 | |||||||||
| 1/2" | Standard | 0.237" | 0.075" | No. 1 | No. 36 | 22 | 25 | 000000000 | 00000 |
| 3/4" | Standard | 0.237" | 0.075" | No. 1 | No. 36 | 22 | 10 | 000000000 | 0000 |
No. 6 | |||||||||
| 1/2" | Standard | 0.262" | 0.083" | No. 2 | No. 32 | 18 | 25 | 000000000 | 00000 |
| 5/8" | Standard | 0.262" | 0.083" | No. 2 | No. 32 | 18 | 25 | 000000000 | 00000 |
| 3/4" | Standard | 0.262" | 0.083" | No. 2 | No. 32 | 18 | 25 | 000000000 | 00000 |
No. 8 | |||||||||
| 5/8" | Standard | 0.312" | 0.1" | No. 2 | No. 29 | 15 | 25 | 000000000 | 00000 |
| 3/4" | Standard | 0.312" | 0.1" | No. 2 | No. 29 | 15 | 10 | 000000000 | 0000 |
Through-Panel-Mount Connectors
Before making a permanent connection, use these connectors to test a circuit. Also known as binding posts, they mount through panels to create a connection point.
All connectors are insulated to prevent contact with panels.
Nickel-plated brass offers a good compromise between conductivity and longevity.
For technical drawings and 3-D models, click on a part number.
| For Use With | For Panel Thick. | Current Per Circuit, A | For Panel Cutout Dia. | No. of Panel Cutouts | Material | Installation | Color | Each | |
Single Hex-Head Post | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| Bare Stranded Wire, Spade Terminals | 0.06"-0.13" | 30 | 0.31" | 1 | Nickel-Plated Brass | Wrench | Black | 0000000 | 000000 |
| Bare Stranded Wire, Spade Terminals | 0.06"-0.13" | 30 | 0.31" | 1 | Nickel-Plated Brass | Wrench | Red | 0000000 | 00000 |
Single Fluted Post | |||||||||
| Banana Plugs, Bare Stranded Wire, Spade Terminals | 0.01"-0.11" | 60 | 0.43" | 1 | Nickel-Plated Brass | Hand Tighten | Black | 0000000 | 00000 |
| Banana Plugs, Bare Stranded Wire, Spade Terminals | 0.01"-0.11" | 60 | 0.43" | 1 | Nickel-Plated Brass | Hand Tighten | Red | 0000000 | 00000 |