Use these general purpose 18-8 stainless steel screws for a variety of fastening applications. They have good chemical resistance.

With a tensile strength of 170,000 psi, these alloy steel screws are among the strongest we carry. They are stronger than Grade 8 steel screws and are more than twice as strong as stainless steel wire-lockable screws. These resist vibration better than any other socket head screw.

More corrosion resistant than 18-8 stainless steel screws, these button head screws have excellent resistance to chemicals and salt water. They may be mildly magnetic.

Brass button head screws are corrosion resistant in wet environments, nonmagnetic, and electrically conductive.

Tighten these screws by turning them to the left; once fastened, they prevent counterclockwise-moving parts from loosening. For use in high-strength fastening applications.

These screws are made to stringent Army-Navy specifications that ensure performance and reliability. They're comparable in strength to Grade 5 steel screws.

Choose these screws for their adherence to strict military standards for material and construction. Screws are 18-8 stainless steel for good chemical resistance.

Bronze screws are 30% stronger than brass screws and provide more corrosion resistance to salt water, gases, and sewage. They are nonmagnetic and electrically conductive.

Place a cotter pin through the hole in the shank to keep a nut from loosening. These screws have a stronger hold than screws with thread lockers or lock washers.

These 18-8 stainless steel screws have good chemical resistance and may be mildly magnetic.

Made from 18-8 stainless steel, these set screws have good chemical resistance.

Brass set screws are corrosion resistant in wet environments, nonmagnetic, and electrically conductive.

Made from black-oxide alloy steel, these set screws resist corrosion in dry environments. They dig into hard surfaces for a secure hold and have serrations on the cup edge that grip the material surface to resist loosening.

The tip makes good contact on flat surfaces and allows you to make frequent adjustments with minimal surface damage.

With a tip that's harder than nylon and silver, these alloy steel set screws provide a secure hold on hard surfaces. The body has a black-oxide finish to resist corrosion in dry environments.

Also known as half dog-point set screws, these set screws have a protruding tip that locks within a mating hole or slot to keep parts aligned.

These alloy steel set screws have a pointed tip that wedges into the contact surface for a secure hold on soft materials such as brass.

Stainless steel set screws have excellent corrosion resistance in most environments.

Tighten these threaded rods by turning them to the left; once fastened, they resist loosening from counterclockwise motion.

Comparable to Grade 8 steel, these threaded rods have a tensile strength of 150,000 psi, making them about 25% stronger than medium-strength steel rods.

Tighten these threaded rods by turning them to the left; once fastened, they resist loosening from counterclockwise motion.

More corrosion resistant than 18-8 and 410 stainless steel threaded rods, these 316 stainless steel rods have excellent resistance to chemicals and salt water.

Brass threaded rods are corrosion resistant in wet environments, electrically conductive, and nonmagnetic.

Change inch threads to metric with these adapters, or swap metric threads for inch. An external hex lets you tighten or loosen them with a wrench.

One side inch, one side metric, and a hex in the middle—these handy fasteners connect two female-threaded parts, such as coupling nuts, adapting from inch threads to metric. Tighten with a standard wrench.

Adapt threaded rods from inch to metric. These adapters connect two male-threaded fasteners, so you can change the gender of a mating part or increase or decrease its thread size. The hex-shaped body fits into the head of a standard wrench.

Designed for use with right-hand, internally threaded rod ends, these rods have right-hand threads on both ends. Use them for remote valve operators, throttle controllers, shifting mechanisms, and virtually any push/pull assembly.

Similar to turnbuckles, these rods have right-hand threads on one end and left-hand threads on the other so you can make a linkage that adjusts for tension. Add right- and left-hand threaded rod ends to build your linkages.

Replace worn or broken caster axles.

Use adapters on the ends of forcing screws and face-grip puller legs when pulling shafts, bearing caps, and pinions.