Use these general purpose 18-8 stainless steel screws for a variety of fastening applications. They have good chemical resistance.

More corrosion resistant than 18-8 stainless steel screws, these 316 stainless steel screws have excellent resistance to chemicals and salt water.

With a tensile strength of 170,000 psi, these alloy steel screws are among the strongest we carry. They are stronger than Grade 8 steel screws and are nearly two and a half times stronger than stainless steel thread-locking screws. They have a thread locker to prevent loosening from vibration.

Seal out contaminants and prevent leaks—a rubber O-ring under the head prevents leaks and seals out contaminants.

More corrosion resistant than 18-8 stainless steel screws, these button head screws have excellent resistance to chemicals and salt water. They may be mildly magnetic.

Brass button head screws are corrosion resistant in wet environments, nonmagnetic, and electrically conductive.

Twice as strong as low-strength steel screws, these screws are suitable for fastening most machinery and equipment.

Use these general purpose 18-8 stainless steel screws for a variety of fastening applications. They have good chemical resistance.

More corrosion resistant than 18-8 stainless steel screws, these 316 stainless steel screws have excellent resistance to chemicals and salt water.

Made from Grade 8 steel, these screws can be used in high-stress applications, such as valves, pumps, motors, and automotive suspension systems. They are at least 25% stronger than medium-strength steel screws. The flange distributes pressure over the surface, eliminating the need for a washer.

Place a cotter pin through the hole in the shank to keep a nut from loosening. These screws have a stronger hold than screws with thread lockers or lock washers.

These 18-8 stainless steel screws have good chemical resistance and may be mildly magnetic.

Made from alloy steel, these screws are nearly twice as strong as stainless steel flat head screws.

Made from 18-8 stainless steel, these inch-sized shoulder screws have good chemical resistance.

More corrosion resistant than 18-8 stainless steel shoulder screws, these have excellent resistance to chemicals and salt water. These screws have inch thread sizes.

Made from 18-8 stainless steel, these set screws have good chemical resistance.

Brass set screws are corrosion resistant in wet environments, nonmagnetic, and electrically conductive.

Made from black-oxide alloy steel, these set screws resist corrosion in dry environments. They dig into hard surfaces for a secure hold and have serrations on the cup edge that grip the material surface to resist loosening.

The tip makes good contact on flat surfaces and allows you to make frequent adjustments with minimal surface damage.

These chemical-resistant 18-8 stainless steel screws have an extra-soft nylon tip, which minimizes the damage that can occur from metal-on-metal contact. Use them on soft surfaces such as aluminum.

With a tip that's harder than nylon and silver, these alloy steel set screws provide a secure hold on hard surfaces. The body has a black-oxide finish to resist corrosion in dry environments.

These 18-8 stainless steel set screws have good chemical resistance. Also known as half dog-point set screws, they have a protruding tip that locks within a mating hole or slot to keep parts aligned.

A nylon locking patch grips threads to resist loosening.

These 18-8 stainless steel set screws are chemical resistant. A pointed tip wedges into the contact surface for a secure hold on soft materials such as brass.

Stainless steel set screws have excellent corrosion resistance in most environments.

These hardened stainless steel screws combine excellent resistance to chemicals and solvents with strength comparable to Grade 9 steel. The head makes 12 points of contact with a wrench to handle more torque than a socket head or hex head screw.

Tighten these threaded rods by turning them to the left; once fastened, they resist loosening from counterclockwise motion.

These are Grade 8 threaded rods.

Grade B8 threaded rods meet the pressure and temperature requirements of ASTM A193 and are often used to secure pressure tanks, valves, and flanges. They have good chemical resistance.

One-third the weight of steel, aluminum threaded rods resist corrosion in wet environments.

A hex drive on one end allows these rods to be turned with a hex key for ease of installation.

Also known as hood pins, these studs have a cotter pin lodged through a drilled hole in the unthreaded portion for light duty holding, such as securing access panels and locking other fasteners.

Change inch threads to metric with these adapters, or swap metric threads for inch. An external hex lets you tighten or loosen them with a wrench.

One side inch, one side metric, and a hex in the middle—these handy fasteners connect two female-threaded parts, such as coupling nuts, adapting from inch threads to metric. Tighten with a standard wrench.

Designed for use with right-hand, externally threaded rod ends, these rods have right-hand threads on both ends. Use them for remote valve operators, throttle controllers, shifting mechanisms, and virtually any push/pull assembly.

Similar to turnbuckles, these rods have right-hand threads on one end and left-hand threads on the other so you can make a linkage that adjusts for tension.

Use adapters on the ends of forcing screws and face-grip puller legs when pulling shafts, bearing caps, and pinions.