Use these general purpose 18-8 stainless steel screws for a variety of fastening applications. They have good chemical resistance.

Made of alloy steel, these low-profile screws are nearly twice as strong as their stainless steel counterparts. With half the height of a standard socket head, these low-profile screws fit in tight spaces.

Choose these metric screws for high-strength fastening. Often used in high-stress applications, such as valves, pumps, motors, and automotive suspension systems, these screws are at least 25% stronger than medium-strength steel screws.

Choose these metric screws for heavy duty stamping applications as well as earth-moving machinery such as bulldozers and excavators. These screws are 10% stronger than our high-strength metric steel screws.

More corrosion resistant than 18-8 stainless steel screws, these 316 stainless steel screws have excellent resistance to chemicals and salt water.

These metric screws are at least 25% stronger than medium-strength steel screws. Use them in high-stress applications, such as valves, pumps, motors, and automotive suspension systems. The flange distributes pressure where the screw meets the surface, so there's no need for a washer.

A high-strength alternative to blind rivets, use these screws when only one side of the material is accessible.

These metric 18-8 stainless steel screws have good chemical resistance and may be mildly magnetic.

Drive the pointed tip of these screws into soft material, such as wood and drywall. They are also known as lag bolts.

These screws have metric thread sizes. They are 18-8 stainless steel for good chemical resistance.

For metric thread sizes with excellent resistance to chemicals and salt water, choose these 316 stainless steel shoulder screws.

These alloy steel set screws have a thin edge that digs into hard surfaces for a secure hold. They're available in metric sizes.

These metric 18-8 stainless steel set screws are chemical resistant. The tip makes good contact on flat surfaces and allows you to make frequent adjustments with minimal surface damage.

These metric set screws have a protruding tip that locks within a mating hole or slot to keep parts aligned. They're also known as dog-point set screws.

Turn these metric screws by hand using the hex head, or tighten them with a wrench for extra torque. With an extended tip that locks into a mating hole or slot—sometimes known as a dog point—they are often used to align and secure parts such as gears and pulley wheels.

These metric set screws have a rolling ball that swivels 360° to minimize surface damage and allow for slight adjustments without loosening the screw.

These bolts have good chemical resistance. Carriage bolts have a smooth, rounded head for a finished look. The square neck keeps these bolts from turning when tightening a nut.

These metric Grade B7 fine-threaded rods meet the pressure and temperature requirements of ASTM A193 and are often used to secure pressure tanks, valves, and flanges.

About half the strength of medium-strength steel threaded rods, use these metric fine-thread rods for light duty hanging, mounting, and fastening.

These metric threaded rods tighten when turned to the left; once fastened, they resist loosening from counterclockwise motion. About half the strength of medium-strength steel threaded rods, use them for light duty hanging, mounting, and fastening.

Class 12.9 rods are about 20% stronger than Class 10.9 threaded rods and are for use in heavy machinery.

These metric 316 stainless steel threaded rods are more corrosion resistant than 18-8 and 410 stainless steel threaded rods and have excellent resistance to chemicals and salt water.

Fiberglass threaded rods are stronger than nylon threaded rods. They resist acids, solvents, salt water, and oil.

Adapt threaded rods from inch to metric. These adapters connect two male-threaded fasteners, so you can change the gender of a mating part or increase or decrease its thread size. The hex-shaped body fits into the head of a standard wrench.

Install with a driver.

These spring plungers have a nose that is about three-times longer than standard long hex-nose spring plungers.

Lock the nose into the retracted position by pulling the handle and rotating it 90°.

Lock the nose into the retracted position by pulling the ring and rotating it 90°.

Multiple thread channels (also known as thread starts) create faster linear travel than lead screws with a single thread start.

Install these threaded collars on a metric lead screw to separate and position components, or use them as an end stop to limit travel.

For quicker setups than a separate T-slot nut and stud, slide these bolts into T-slot tracks on machine tool tables.

Also known as nut eyebolts, these are designed for through-hole applications.

Route wire and cable through the smooth eye without snagging.

Designed for use with right-hand, externally threaded rod ends, these rods have right-hand threads on both ends. Use them for remote valve operators, throttle controllers, shifting mechanisms, and virtually any push/pull assembly.

Similar to turnbuckles, these rods have right-hand threads on one end and left-hand threads on the other so you can make a linkage that adjusts for tension.