We will reply to your message within an hour.
The standard for high-strength fastening.
Use these general purpose 18-8 stainless steel screws for a variety of fastening applications. They have good chemical resistance.
Choose these metric screws for high-strength fastening. Often used in high-stress applications, such as valves, pumps, motors, and automotive suspension systems, these screws are at least 25% stronger than medium-strength steel screws.
Choose these metric screws for fastening most machinery and equipment. They are twice as strong as low-strength steel screws.
Choose these metric screws for heavy duty stamping applications as well as earth-moving machinery, such as bulldozers and excavators. These screws are 10% stronger than our high-strength metric steel screws.
More corrosion resistant than 18-8 stainless steel screws, these 316 stainless steel screws have excellent resistance to chemicals and salt water.
Designed for construction and exterior building applications, these metric screws are often used to join I-beams and scaffolding. Their partial threading leaves an unthreaded portion that is strong enough to stand up to the sideways forces of joints.
These screws have metric thread sizes. They are 18-8 stainless steel for good chemical resistance.
These alloy steel set screws have a thin edge that digs into hard surfaces for a secure hold. They're available in metric sizes.
These metric set screws have a tip that makes good contact on flat surfaces and allows you to make frequent adjustments with minimal surface damage.
These metric set screws have a protruding tip that locks within a mating hole or slot to keep parts aligned. They're also known as dog-point set screws.
These metric set screws have a rolling ball that swivels 360° to minimize surface damage and allow for slight adjustments without loosening the screw.
The tensile strength of these metric Grade B7 rods is about one and a half times higher than low-strength steel rods.
Made of Grade B7 steel, the tensile strength of these threaded rods is one and a half times higher than low-strength steel threaded rods. They also meet the pressure and temperature requirements of ASTM A193 and are often used to secure pressure tanks, valves, and flanges.
An economical alternative to Grade B7 and Grade B16 threaded rods, these metric Class 8.8 rods are suitable for fastening most machinery and equipment.
These Class 10.9 steel threaded rods are about 25% stronger than medium-strength steel rods.
Class 12.9 rods are about 20% stronger than Class 10.9 threaded rods and are for use in heavy machinery.
These metric threaded rods are about half the strength of medium-strength steel threaded rods for light duty hanging, mounting, and fastening.
About half the strength of medium-strength steel threaded rods, use these metric fine-thread rods for light duty hanging, mounting, and fastening.
These metric threaded rods tighten when turned to the left; once fastened, they resist loosening from counterclockwise motion. About half the strength of medium-strength steel threaded rods, use them for light duty hanging, mounting, and fastening.
Available in metric sizes, these 18-8 stainless steel threaded rods have good chemical resistance.
These metric 316 stainless steel threaded rods are more corrosion resistant than 18-8 and 410 stainless steel threaded rods and have excellent resistance to chemicals and salt water.
Also known as setup studs, these studs withstand sideways forces better than fully threaded studs because they have an unthreaded middle that is stronger than the treaded ends.
These spring plungers have a nose that is about three-times longer than standard long hex-nose spring plungers.
Also known as trapezoidal-thread lead screws and nuts.
Install these threaded collars on a metric lead screw to separate and position components, or use them as an end stop to limit travel.
Also known as machinery eyebolts.
Also known as nut eyebolts, these are designed for through-hole applications.
Unlike conventional eyebolts, you can rotate the eye 360° to match the angle of your load.
Route wire and cable through the smooth eye without snagging.
Create your own lifting eye by adding an eye nut to a stud or bolt.
Also known as transfer screws, these punches have a uniform shoulder height so you can quickly transfer multiple hole locations at once.