Multiple internal springs ensure these seals keep the sealing surfaces in contact in demanding applications, such as agricultural, chemical, and mining pumps.

Rated for pressure up to 10,000 psi, these leather U-cups handle over 80 times more pressure than our Buna-N U-cups.

PTFE gives these seals a slippery surface that allows rod speeds more than two times faster than our other piston seals.

Rated for pressure up to 10,000 psi, these seals withstand the highest pressure of our piston seals.

Replace wipers in open-groove cylinders—these wipers have an integral steel case so they press fit into the groove around the rod.

Cut this stock to make wear rings that fit any rod or bore diameter.

These leather V-ring packing seals handle over twice the pressure as PTFE. Leather is tough, pliable, and wear resistant, so it flexes to fit uneven surfaces and fill voids.

This thin lubricant penetrates into tight spaces, and nano-sized additives fill small surface imperfections, reducing wear and heat and extending the life of both the lubricant and equipment.

For use in food-processing and preparation areas, these thin, multipurpose lubricants are NSF registered H1 or FDA compliant for incidental food contact.

Protect food-processing and preparation equipment while limiting environmental impact. These multipurpose lubricants are NSF registered H1 for incidental food contact and are rated to quickly break down in water.

Thickened with silica, this heavy grease clings to parts so it won't wash off in wet environments.

Fluorocarbon and fluorinated polymer thickeners add chemical resistance to this grease. It remains intact when exposed to water and most solvents and chemicals.

This grease meets NSF/ANSI Standard 51 and FDA 21 CFR 175.300 for direct contact with food and NSF/ANSI Standard 61 for use with components that come into contact with drinking water.

Nano-sized additives penetrate small surface imperfections, reducing wear and heat and extending the life of both the lubricant and equipment. Use it with bearings, rollers, and other equipment subjected to high loads.

For use in food-processing and preparation areas, this petroleum jelly is NSF registered H1 for incidental food contact.

Formulated to adhere to metal parts and stay in place in wet environments, this grease is commonly used in pulp and paper manufacturing and water management facilities.

Waterproof and heat-resistant, this grease can be autoclaved without washing out of equipment. It's chemically inert, so it won't interact with process fluids.

For use on metal parts to prevent corrosion and as an antiseize lubricant. Gauges are often coated in a thin layer of lanolin to move smoothly and maintain their precision.

For use in food-processing and preparation areas, this grease is rated for incidental contact with food.

Highly pure and with no additives to contaminate sensitive environments, use this grease in clean rooms and electronic assembly workstations.

Nano-sized additives fill small surface imperfections, reducing wear and heat to extend the life of both the lubricant and equipment. These lubricants dry to form a nonstick film that won’t attract dust. They are often used on hinges, gears, and roller chain.

Use at pressures up to 50,000 psi.

Apply directly to seals and O-rings to extend service life by preventing drying and cracking.

For use in food-processing and preparation areas, these lubricants are rated for incidental food contact. Coat tight-fitting parts with them before sliding together to make assembly easier.

Made of silver-plated 321 stainless steel, these O-rings can handle extreme pressure up to 11,000 psi. They resist grease, hydraulic oils, mineral oil, motor oil, and synthetic lubricants.

Softer than standard Viton® fluoroelastomer O-rings, these offer a better seal in low-pressure applications.

Inherently softer and more compressible than PTFE O-rings, these Kalrez 4079 O-rings have comparable chemical resistance.

Made of Kalrez 6230, these O-rings are for use when high purity is essential, such as with food and semiconductors.

These PTFE backup rings resist harsh chemicals, such as acetone, fluorinated solvents, methanol, and many acids.

This square-profile cord stock has flat edges on all four sides, which creates a better seal than round profile in static applications, such as hose, pipe, and faucet connections.

This square-profile cord stock has flat edges on all four sides, which creates a better seal than round profile in static applications, such as hose, pipe, and faucet connections.

Harder than standard Viton® fluoroelastomer cord stock for better wear resistance.

This cord stock is made of FDA-listed material for use with food and beverage. It resists citric acid, diluted salt solutions, glycerin, and sodium bicarbonate.

More chemical resistant than standard Viton® fluoroelastomer, this cord stock is made of Grade ETP Viton® fluoroelastomer. It resists harsh chemicals, such as calcium hydroxide, methyl ethyl ketone (MEK), and nitric and phosphoric acids.

Use this cord stock to create O-rings for high-temperature applications up to 400° F.

Create round-profile O-rings for sealing applications near ovens and other hot areas in your food plant.

All of the O-rings in these assortments are made of Buna-N. They resist animal, vegetable, and motor oils.

These O-rings are harder than standard Buna-N O-rings for better resistance to wear.

Also known as Boss O-rings, these hard Viton® fluoroelastomer O-rings are for use in tube fittings with a straight-thread connection. They offer excellent resistance to wear.

These assortments contain a mix of Buna-N O-rings that resist oil and Viton® fluoroelastomer O-rings that resist boric acid, fuels, and transmission fluid.

Thinner than non-sagging sealants, these flow easily into cracks and have a smooth finish.

Thinner than non-sagging sealants, these flow easily into cracks and have a smooth finish.

Apply these thread sealant sticks without a mess.

Much thicker than sealants for fine threads, these sealants bridge the gaps between coarse threads.

Often used in high-vibration applications that could cause standard thread sealants to fail, these never fully harden and remain pliable enough to self-heal and stop leaks before they start.

These sealants come in bottles, cans, and tubes so you can choose the quantity that covers your application.

Completely free of oil and chemically inert, these sealants are safe to use with wet and dry oxygen systems.

This tape has a higher density than standard tape for a better seal between threads.

Made of PTFE, this tape has a slippery surface that keeps threads from binding to make parts easy to assemble.