For Use On For Use On |
|---|
Type Type |
|---|
|
Maximum Temperature Maximum Temperature |
|---|
|
Formulation Formulation | Show |
|---|
|
Formulation Formulation | Hide |
|---|
System of Measurement System of Measurement |
|---|
|
Overall Dry Time Overall Dry Time |
|---|
|
Approximate Coverage @ Thickness Approximate Coverage@ Thickness |
|---|
|
Maximum Application Temperature Maximum ApplicationTemperature |
|---|
|
Minimum Application Temperature Minimum ApplicationTemperature |
|---|
|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
|---|
|
Container Size Container Size |
|---|
|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement)  |
|---|
Length Length |
|---|
|
Width Width |
|---|
|
Composition Composition |
|---|
|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
|---|
|
About Paint and Protective Coatings
More
Powder Coatings
More durable and scratch resistant than liquid paint, use this dry paint with your powder coating system. Apply directly to unpainted metal and heat-cure in an oven for a smooth, baked-on finish. Before using this powder on aluminum, completely clear the surface of any aluminum oxides.
Dry Time | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| Container Net Weight, oz. | Composition | Touch, min. | Overall, min. | Approx. Coverage @ Thick. | Max. Temp., °F | Application Temp. Range, °F | For Use On | Choose a Color (Appearance) | Each | |
| 16 | Solvent Based | 10 | 10 | 68 sq. ft. @ 2 mil | 350° | 50° to 80° | Aluminum, Brass, Bronze, Copper, Steel, Titanium, Iron | 0000000 | 000000 | |
Surface Fillers
These surface fillers can be used on vertical surfaces without sagging. They repair cracked, worn, and damaged surfaces. The size listed is the combined total of the two parts.
Container | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Mfr. Model No. | Size | Type | Begins to Harden, min. | Reaches Full Strength | Consistency | Mix Ratio | Approx. Coverage @ Thick. | Temp. Range, °F | Color | Finishing Method | For Use On | Each | |
Bondo Body Filler | |||||||||||||
| 261 | 1 pt. | Can, Tube | 3 | 60 min. | Paste | 50:1 | 90 sq. in. @ 1/4" | -40° to 180° | Gray | Sand | Aluminum, Steel, Concrete, Fiberglass, Wood | 000000000 | 000000 |
| 262 | 1 qt. | Can, Tube | 3 | 60 min. | Paste | 50:1 | 180 sq. in. @ 1/4" | -40° to 180° | Gray | Sand | Aluminum, Steel, Concrete, Fiberglass, Wood | 000000000 | 00000 |
Surface Fillers | |||||||||||||
| __ | 8 fl. oz. | Tube | 15 | 3 hrs. | Paste | 50:1 | Not Rated | -40° to 180° | Yellow to Green-Blue | Sand | Fiberglass | 0000000 | 00000 |
| Replacement Hardener for Bondo Surface Fillers (0.8-fl. oz. Tube) | 000000000 | Each | 00000 |
Light-Activated Surface Filler Patches
An easy way to make repairs in the field. Cut patches to size, peel off the backing, and press into place. When exposed to sunlight or a UV lamp, they begin to harden immediately. Patches are waterproof.
| Formulation | Lg. | Wd. | Begins to Harden, sec. | Reaches Full Strength, min. | For Use Outdoors | Temp. Range, °F | Color | Finishing Method | For Use On | Each | |
| Polyester | 6" | 3" | 1 | 50 | Yes | -40° to 350° | Yellow | Drill, Sand | Vinyl Plastic, EPDM Rubber, SBR Rubber, Fiberglass, Concrete | 0000000 | 000000 |
Light-Activated Surface Fillers
Press these putty surface fillers in place to fill in holes, cracks, and dents. When exposed to sunlight or a UV lamp, they begin to harden immediately.
Container | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Formulation | Size, fl. oz. | Type | Begins to Harden, sec. | Reaches Full Strength, min. | Consistency | For Max. Crack Wd. | Approx. Coverage @ Thick. | Max. Thick. | For Use Outdoors | Temp. Range, °F | Color | Finishing Method | For Use On | Each | |
| Polyester | 3.5 | Tube | 1 | 3 | Putty | 1" | 24 sq. in. @ 1/4" | 1/2" | Yes | -40° to 220° | White | Drill, Sand, Tap | Aluminum, Brass, Copper, Steel, Stainless Steel, Cast Iron, Titanium, Polycarbonate Plastic, Polyurethane Rubber, ABS Plastic, PVC Plastic, CPVC Plastic, PETG Plastic, PVDF Plastic, Polyimide Plastic, Fiberglass, Wood | 00000000 | 000000 |