These switches withstand temporary submersion.

With a slim shape, these switches fit comfortably in your hand.

Install in 14 mm dia. cutouts.

Rated NEMA 4X and 13, all switches resist corrosion and can withstand washdowns and oil/coolant spraying.

With a stainless steel enclosure, these switches are more durable than aluminum and plastic. They're rated NEMA 4X for protection from corrosion and washdowns.

Rated NEMA 3S, NEMA 4X, NEMA 13, and IP66, these plastic switches resist corrosion better than aluminum switches and withstand washdowns and oil/coolant spraying.

Pull the hanging rope in any direction to actuate these switches.

Prevent personnel from getting too close to dangerous equipment when equipment is on—these mats turn equipment off when someone steps on them or when a fault is detected.

These narrow switches are also thin enough to be hidden under carpeting or installed anywhere space is limited.

Safe for use in wet locations, these switches are IP and NEMA rated for protection from corrosion, washdowns, and oil/coolant spraying.

Control equipment from up to 40 feet away—these switches include a transmitter and a receiver that connects to equipment.

Press these switches with your foot for convenient, hands-free operation.

Replace access door hinges with these switches; they actuate when the door opens at least 4°.

Delay access to hazardous areas until conditions are safe; use these switches with machines that take time to stop after they are turned off. They mount to a door frame.

Sealed actuators prevent these switches from jamming, even when exposed to sand, mud, or dirt. They're rated IP67 for protection from temporary submersion.

Secure these switches into panels using mounting nuts.

Rated NEMA 6P, 13, and IP67, these switches are protected from corrosion, oil/coolant spraying, washdowns, and temporary submersion.

Shorter and thinner than other safety limit switches, these are sized to fit tight spaces.

Prevent equipment from automatically restarting—these switches must be manually reset each time they're actuated.

Small enough to fit in the tiniest spaces, these switches are rated IP67 for protection from temporary submersion.

With a rubber-encased housing and stainless steel bracket, these switches resist vibration and corrosion. They're rated IP68 for protection from dust and temporary submersion.

Enclosures protect these snap-acting switches from the environment.

Sensitive along their entire length, these switches are often used to signal when an overhead door closes or an item reaches the end of a conveyor.

For optimal performance in tight spaces, these switches have a smaller beam and can detect smaller objects than standard photoelectric switches.

Rated IP69K, these switches can withstand high-pressure, high-temperature washdowns and temporary submersion.

Detect the presence or absence of an object moving at high speeds with a light beam. These switches have a longer sensing distance than proximity and ultrasonic switches.

The highly flexible fiber-optic cable and small sensing end help you position these switches in hard to reach areas.

Safely detect the presence or absence of an object moving at high speeds with a light beam. These switches produce a low-current, low-voltage NAMUR signal, so they won’t create sparks or ignite. ATEX and IECEx certified, they protect against explosion in environments containing flammable gases and combustible dust.

Support flow and temperature control in your system with these intrinsically safe switches, which sense when a valve is open or closed in volatile areas. They are ATEX and IECEx certified to protect against explosion.

These switches use a NAMUR signal to operate at a low current and voltage, so they won’t ignite or produce sparks. ATEX certified, they protect against explosion in environments containing flammable gases and combustible dust. Switches sense both metallic and nonmetallic objects.

Easily mount these flat switches to a base or rail.

Switches accept both AC and DC input voltage.

Twist the sensor to detect metallic objects where explosive dust or gas may be present—the sensor rotates for front, side, top, or bottom sensing. These switches are UL and C-UL listed as well as ATEX and IECEx certified for hazardous locations.

These switches use DC input voltage and produce PNP or NPN signal output. They're often used with programmable logic controllers (PLCs).

Eliminate the need to calculate the sensing distance when using different metals—these switches sense all metal at the same distance. Also known as K=1 sensors.

Mount these flat inductive switches to a base or rail to remotely detect metallic objects in wet and dirty environments.

The flexible cable on these switches withstands applications that require frequent motion, such as robotics.

The short body on these switches makes them suitable for tight spaces.

These inductive proximity switches sense metallic objects each time they pass through the slot, even when they’re obscured by water, oil, dirt, or a surface finish. Use them to measure the speed of rotating equipment and to count or detect moving objects, such as sheet metal being fed into a stamping process.

Turn the face on these switches to sense metallic objects from the front, sides, top, or bottom.

These intrinsically safe switches detect objects as they’re routed through the ring. They produce a low-current, low-voltage NAMUR signal, so they won’t ignite or create sparks. Switches are ATEX certified to protect against explosion.

Easily mount these flat switches to a base or rail.

These switches actuate when a magnet comes within sensing distance, and reset when the magnet moves away.

Rated IP66, these switches are protected from washdowns.

Install these switches in a panel cutout.

These switches are housed in a protective enclosure so they can be mounted wherever needed.

The NEMA 4X rated enclosure protects these starters from corrosion and washdowns.

Assemble your own motor starter by combining a switch and a thermal overload element.