We will reply to your message within an hour.
More
Resistant to mold and mildew, these sealants are well suited to high-humidity environments.
Also known as neutral-cure sealants, these won't discolor copper, brass, and concrete.
A combination of hardness and surface tension makes these sealants resistant to punctures, cuts, and abrasion.
Apply these sealants in cold temperatures, on wet surfaces, and even through running water.
Meeting requirements for semiconductor, biomedical, and electronics clean rooms, these sealants won’t contaminate air and surfaces.
These structural sealants combine the mechanical strength of an adhesive with excellent sealing properties and high flexibility.
With chemical and metal additives that are picked up by X-ray machines and metal detectors, these sealants are designed to help you comply with Hazard Analysis and Critical Control Point (HACCP) programs in food-processing facilities.
Mix a small amount of water-based paint with this caulk to match the color of your surface.
Also known as thumb-grade caulk, this forms a non-hardening, moisture-resistant seal that remains pliable.
Thinner than non-sagging sealants, these flow easily into cracks and have a smooth finish.
Thinner than non-sag sealants, these flow easily into cracks and have a smooth finish.
These non-sagging sealants will not drip while hardening on vertical and overhead surfaces.
These sealants are non-sagging, so they won't drip from vertical and overhead surfaces.
Use these coatings on tanks to create a low-friction lining that prevents bubble formation and turbulence in the liquids within.
Used to insulate, create grips, and color-code components, these coatings resist high temperatures, light abrasion, and corrosion.
Made with Viton® fluoroelastomer, use these coatings to create a flexible coating on rollers, heavy equipment, and anything else that’s exposed to corrosive chemicals or extreme temperatures.
Use these coatings in kitchens, furnace areas, and ships on plastic, metal, wood, and masonry.
Longer-lasting than antislip tape, these coatings contain grit to provide traction. They’re good for areas with pedestrian traffic.
Seal brick, mortar, and concrete to prevent water damage. These coatings create a thin, clear layer that sits on the surface of masonry and repels water.
Protect clothing, furniture, and other fabric with these oil- and water-repellent coatings. Also known as oleophobic and hydrophobic coatings, they work into a fabric’s individual fibers to repel liquid and grease.
Made of rubber and iron oxide, these sheets can be cut with scissors to create custom-shaped nonmetallic, nonmagnetic surface that magnets will stick to.
Cover scratches and wear on storage racks and carts. Match the color to your manufacturers' equipment color.
These thin primers penetrate deeply into concrete floors to create a hard surface that can then be coated with any urethane or epoxy coating.
Make a temporary repair to cracks in any flat roof. These patching compounds are a powder that forms a thick gel in minutes when poured directly into standing water and rain.
Repair holes and seal gaps in roofing and gutters. These patching compounds are durable and water resistant.
These patching compounds are the most flexible and watertight we offer.
Roll out a fast fix for leaky roofs and gutters with these peel-and-stick rolls.
Reinforce hot- and cold-applied asphalt patching compounds and coatings with this flexible fabric.
These surface fillers come in a pen for precision application. After applying, use the LED on the back of the pen to instantly cure.
Fill cracks in horizontal, vertical, and overhead concrete surfaces.
Stop slow-flowing and weeping leaks in concrete. Also known as hydraulic cement, these crack fillers begin to harden in three to five minutes to create a permanent fix that won't shrink.
Stop active leaks of up to 50 gallons per minute in concrete, brick, and stone. These crack fillers begin to harden within seconds to create a permanent fix that won't shrink.
Fill in and shape horizontal, vertical, and overhead concrete surfaces, such as steps and columns.
Use these two-part compounds to patch concrete floors, stairs, and walls in cold environments, such as freezers. At room temperature, they cure faster than any of our other concrete patching compounds.
Cover large sections of damaged concrete with these durable patching compounds. Made up of a resin, hardener, and aggregate, they cover more area than any of our other concrete patching compounds.
For use when thickness will be less than 2", sand mixes consist of cement and sand.
For use when thickness will be more than 2", concrete mixes consist of cement, sand, and gravel.
Used on ceramic, concrete, and stone floor and wall tiles, grout consists of fine sand, masonry cement, and coloring.
Mix this two-part epoxy—a resin-aggregate blend and a pigmented hardener—to create a grout that resists chemicals and doesn't require sealing. Use on ceramic, concrete, and stone floor and wall tiles.
Used for brick, block, and stone laying as well as for repairing masonry, mortar mixes consist of fine sand and masonry cement.
These durable finishes are detergent resistant and dry to a clear, high-gloss shine.
Remove silicone, foam sealants, caulk, wet or dry latex-based foams, and construction adhesives.