System of Measurement System of Measurement |
---|
|
For Shaft Diameter For Shaft Diameter | Show |
---|
|
For Shaft Diameter For Shaft Diameter | Hide |
---|

For Motion Type For Motion Type |
---|
![]() | Rotary |
For Use With For Use With |
---|
For Sealing For Sealing |
---|
![]() |
Shafts |
Material Material |
---|
|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
---|
|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
---|
Hardness Rating Hardness Rating |
---|
|
Hardness Hardness |
---|
|
Maximum Temperature Maximum Temperature |
---|
|
Flange OD Flange OD |
---|
|
Spring-Loaded Rotary Shaft Seals



Also known as oil seals, use these to retain oil on rotating shafts in motors, pumps, bearings, and gearboxes. A spring secures the lip against the shaft, preventing messy leaks. Press-fit seals into the bore around the shaft.
Seals with an acrylic-coated case have a coating that compensates for surface imperfections in the housing bore for a tight seal on the OD.
Note: Maximum performance values cannot be achieved simultaneously; for example, speed is affected by pressure, temperature, and other operating conditions.
For technical drawings and 3-D models, click on a part number.

For Bore | Case | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | Dia. | Min. Wd. | Max. Speed, rpm | Max. Pressure, psi | Temp. Range, °F | Hardness | Color | Finish | Color | Specifications Met | Each | |
Buna-N Rubber with Steel Case and Spring | ||||||||||||
2 3/8" | 3.125" | 0.391" | 2,700 | 10 | -40° to 210° | Durometer 75A (Hard) | Black | Acrylic Coated | Green | DIN 3760, ISO 6194 | 00000000 | 000000 |
High-Speed Rotary Shaft Seals




A slippery PTFE surface allows these seals to function at speeds at least 25% faster than other rotary shaft seals. Also known as oil seals, use these to retain oil on rotating shafts in motors, pumps, bearings, and gearboxes. An O-ring secures the lips to prevent leaks, while sealing against the housing. Press-fit seals into the bore around the shaft.
Note: Maximum performance values cannot be achieved simultaneously; for example, speed is affected by pressure, temperature, and other operating conditions.
For technical drawings and 3-D models, click on a part number.
For Bore | O-Ring | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | Dia. | Min. Wd. | Max. Speed, rpm | Max. Pressure, psi | Temp. Range, °F | Hardness | Color | Hardness | Color | Each | |
Graphite-Filled PTFE Plastic with Buna-N Rubber O-Ring | |||||||||||
2 3/8" | 2.875" | 0.323" | 8,000 | 150 | -40° to 250° | Durometer 60D (Extra Hard) | Black | Durometer 70A (Hard) | Black | 0000000 | 000000 |
Shaft-Mounted Rotary Seals
Also known as V-rings and flingers, these seals protect shaft bearings by blocking dust and other contaminants while retaining lubricant. They’re Buna-N for excellent resistance to oil and grease. To install, stretch the seal over your shaft and press it firmly against the face plate. The Seal ID, OD, and Width listed are the dimensions of the seal after it is installed.
Note: Maximum performance values cannot be achieved simultaneously; for example, speed is affected by pressure, temperature, and other operating conditions.
For technical drawings and 3-D models, click on a part number.




For Shaft | Seal | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Dia. | Dia. Range | For Face Plate Dia. | ID | OD | Wd. | Max. Speed, rpm | Max. Pressure, psi | Temp. Range, °F | Hardness | Color | Each | |
Buna-N Rubber | ||||||||||||
2 3/8" | 2.290"-2.480" | 2.890"-3.080" | 2.107" | 2.975" | 0.500" | 2,900 | 100 | -20° to 225° | Durometer 85A (Hard) | Black | 0000000 | 00000 |
Heavy Duty Shaft-Mounted Rotary Seals




These seals are fluoroelastomer, so they have excellent chemical resistance and withstand temperatures up to 390° F. Also known as V-rings and flingers, they protect shaft bearings by blocking dust and other contaminants while retaining lubricant. To install, stretch the seal over your shaft and press it firmly against the face plate.
Note: Maximum performance values cannot be achieved simultaneously; for example, speed is affected by pressure, temperature, and other operating conditions.
For technical drawings and 3-D models, click on a part number.
For Shaft | Seal | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Dia. | Dia. Range | For Face Plate Dia. | ID | OD | Wd. | Max. Speed, rpm | Max. Pressure, psi | Temp. Range, °F | Hardness | Color | Each | |
Fluoroelastomer Rubber | ||||||||||||
2 3/8" | 2.283"-2.48" | 2.874"-3.071" | 2.126" | 2.520" | 0.354" | 2,800 | 5 | 5° to 390° | Durometer 60A (Medium) | Brown | 0000000 | 000000 |
Shaft Repair Sleeves


Also known as speedi sleeves, use these to repair and protect worn shafts for a smooth sealing surface without machining. Each sleeve comes with an installation tool. To install, place the installation tool around the sleeve and gently tap the installation tool until the sleeve covers the worn shaft surface.
For technical drawings and 3-D models, click on a part number.
For Shaft | Flange | |||||||
---|---|---|---|---|---|---|---|---|
Dia. | Dia. Range | Max. Installed Dp. | Sealing Face Wd. | OD | Wd. | Sleeve Thick. | Each | |
300 Series Stainless Steel | ||||||||
2 3/8" | 2.374"-2.380" | 1.375" | 0.781" | 2.750" | 0.157" | 0.011" | 0000000 | 000000 |