System of Measurement System of Measurement |
|---|
|
For Shaft Diameter For Shaft Diameter | Show |
|---|
|
For Shaft Diameter For Shaft Diameter | Hide |
|---|
For Motion Type For Motion Type |
|---|
 | Rotary |
For Use With For Use With |
|---|
Maximum Temperature Maximum Temperature |
|---|
|
For Sealing For Sealing |
|---|
 |
| Shafts |
Hardness Rating Hardness Rating |
|---|
|
Hardness Hardness |
|---|
|
Spring Material Spring Material |
|---|
|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
|---|
|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement)  |
|---|
High-Speed Rotary Shaft Seals
A slippery PTFE surface allows these seals to function at speeds at least 25% faster than other rotary shaft seals. Also known as oil seals, use these to retain oil on rotating shafts in motors, pumps, bearings, and gearboxes. An O-ring secures the lips to prevent leaks, while sealing against the housing. Press-fit seals into the bore around the shaft.
Note: Maximum performance values cannot be achieved simultaneously; for example, speed is affected by pressure, temperature, and other operating conditions.
For technical drawings and 3-D models, click on a part number.
For Bore | O-Ring | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Dia. | Min. Wd. | Max. Speed, rpm | Max. Pressure, psi | Temp. Range, °F | Hardness | Color | Hardness | Color | Each | |
Graphite-Filled PTFE Plastic with Buna-N Rubber O-Ring | |||||||||||
| 4" | 4.500" | 0.323" | 4,800 | 150 | -40° to 250° | Durometer 60D (Extra Hard) | Black | Durometer 70A (Hard) | Black | 0000000 | 000000 |
Split Rotary Shaft Seals
Replace old seals without disassembling components—these seals come split for easy installation. Also known as clipper seals, they retain oil on rotating shafts in motors, pumps, bearings, and gearboxes. A spring secures the lip to prevent leaks; fasten the hook and eye closure to secure. Press-fit seals into the housing bore; they fit tight for installation without a cover plate.
Note: Maximum performance values cannot be achieved simultaneously; for example, speed is affected by pressure, temperature, and other operating conditions.
For technical drawings and 3-D models, click on a part number.
For Bore | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Dia. | Min. Wd. | Max. Speed, rpm | Temp. Range, °F | Hardness | Color | Case Color | Each | |
Buna-N Rubber with Aramid Fiber Case and Stainless Steel Spring | |||||||||
| 4" | 5.000" | 0.500" | 1,900 | -20° to 250° | Durometer 75A (Hard) | Black | Black | 0000000 | 000000 |
Shaft-Mounted Rotary Seals
Also known as V-rings and flingers, these seals protect shaft bearings by blocking dust and other contaminants while retaining lubricant. They’re Buna-N for excellent resistance to oil and grease. To install, stretch the seal over your shaft and press it firmly against the face plate. The Seal ID, OD, and Width listed are the dimensions of the seal after it is installed.
Note: Maximum performance values cannot be achieved simultaneously; for example, speed is affected by pressure, temperature, and other operating conditions.
For technical drawings and 3-D models, click on a part number.
For Shaft | Seal | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Dia. | Dia. Range | For Face Plate Dia. | ID | OD | Wd. | Max. Speed, rpm | Max. Pressure, psi | Temp. Range, °F | Hardness | Color | Each | |
Buna-N Rubber | ||||||||||||
| 4" | 3.860"-4.140" | 4.460"-4.740" | 3.551" | 4.609" | 0.500" | 1,700 | 100 | -20° to 225° | Durometer 85A (Hard) | Black | 0000000 | 000000 |
Heavy Duty Shaft-Mounted Rotary Seals
These seals are fluoroelastomer, so they have excellent chemical resistance and withstand temperatures up to 390° F. Also known as V-rings and flingers, they protect shaft bearings by blocking dust and other contaminants while retaining lubricant. To install, stretch the seal over your shaft and press it firmly against the face plate.
Note: Maximum performance values cannot be achieved simultaneously; for example, speed is affected by pressure, temperature, and other operating conditions.
For technical drawings and 3-D models, click on a part number.
For Shaft | Seal | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Dia. | Dia. Range | For Face Plate Dia. | ID | OD | Wd. | Max. Speed, rpm | Max. Pressure, psi | Temp. Range, °F | Hardness | Color | Each | |
Fluoroelastomer Rubber | ||||||||||||
| 4" | 3.858"-4.134" | 4.567"-4.843" | 3.543" | 4.016" | 0.433" | 1,700 | 5 | 5° to 390° | Durometer 60A (Medium) | Brown | 0000000 | 000000 |