Ribbed Buna-N over steel creates a tight seal with the bore, even when mating with a rough surface or in a split housing.

Also known as oil seals, use these to retain oil on rotating shafts in motors, pumps, bearings, and gearboxes. A spring secures the lip against the shaft, preventing messy leaks. Press-fit seals into the bore around the shaft.

Also known as grease seals, these are designed to retain thick lubricant at low pressure. They have a light grip on the shaft that creates less friction than spring-loaded seals.

Swap out old seals without disassembling components—these seals come split for easy installation. They're also known as clipper seals.

These seals are fluoroelastomer, so they have excellent chemical resistance and withstand temperatures up to 390° F.

With a smaller seal OD than standards seals, these seals have an extended spring that accommodates variations in seal cavity length.

Multiple internal springs ensure these seals keep the sealing surfaces in contact in demanding applications, such as agricultural, chemical, and mining pumps.

Also known as loaded-lip seals and PolyPaks, an O-ring secures these U-cups to the rod or piston for better sealing performance at lower pressures than unsupported U-cup seals.

These U-cup seals create less friction than O-ring-loaded U-cups, so they wear more slowly. Also known as lip seals, U-cups have a sealing lip on both the inside and outside edges, so they can be used for rod and piston sealing.

These seals have a beveled lip that optimizes contact against the rod, while a secondary lip keeps the seal stable.

The slippery PTFE surface of these seals allows rod motion up to seven times faster than our other rod seals.

PTFE gives these seals a slippery surface that facilitates rod speeds over seven times faster than our other buffering seals. They're rated for pressure up to 5,000 psi.

PTFE gives these seals a slippery surface that allows rod speeds more than two times faster than our other piston seals.

Avoid common O-ring failure in dynamic applications—the square base of these seals prevents twisting, while backup rings protect against extrusion.

A two-lip design means that these wipers also function as a rod seal.

Made from MDS-filled PTFE for a slippery surface, these wipers allow rods to move three times faster than other rod wipers.

Made from glass-filled nylon for excellent wear resistance and strength.

Aramid and PTFE fibers are blended for seals that resist chemicals and abrasion. Use these seals in pumps.

Built for high-speed pump and valve applications, these super-tough seals are made of expanded-graphite yarn with carbon-yarn corners.

These lubricated PTFE fiber seals stand up to most chemicals. Use them in pumps and valves.

Made of PTFE-impregnated synthetic fiber, these seals are for use in pumps.

The most abrasion resistant of all our packing seals, these are made of PTFE-impregnated aramid fiber that has been saturated in a lubricant. They are for use in pumps.

Use these graphite-impregnated graphite seals for steam applications in pumps and valves.

These leather V-ring packing seals handle over twice the pressure as PTFE. Leather is tough, pliable, and wear resistant, so it flexes to fit uneven surfaces and fill voids.

Use these Viton® fluoroelastomer rubber seals with fuels and aggressive chemicals, such as petroleum oil, hydrofluoric acid, and propyl alcohol.

The Buna-N foam rubber bulb on these seals also resists grease, salts, water, steam, and most detergents.

Made of fiberglass, these seals are woven tighter than High-Temperature Ultra-Conformable Slotted Edge Seals for increased durability. They resist grease, oil, hydraulic fluid, and solvents and can withstand temperatures up to 1000° F.

Flexible even at temperatures as low as -80° F, these fluorosilicone O-rings will keep your fittings free from leaks. They’re often used on fuel and coolant hose because fluorosilicone resists many chemicals, including ethanol and ethylene glycol.

These non-sagging sealants will not drip while hardening on vertical and overhead surfaces.

These non-sagging sealants will not drip while hardening on vertical and overhead surfaces.

These sealants come in bottles, cans, and tubes so you can choose the quantity that covers your application.

Much thicker than sealants for fine threads, these sealants bridge the gaps between coarse threads.

These sealants come in bottles, cans, and tubes so you can choose the quantity that covers your application.

Formulated for high lubricity, these sealants allow easy assembly of finely threaded hydraulic and compressed air system components. They're also free of fillers that could contaminate system media.

Use color to identify water, gas, and chemical connections.