Rated NEMA 4, 13, and IP66, these metal switches are protected from washdowns and oil/coolant spraying. Install them in 22 mm dia. cutouts.

These plastic switches are rated NEMA 4X, 13, and IP65 for protection from corrosion, washdowns, and oil/coolant spraying. Install them in 30 mm dia. cutouts.

Rated NEMA 4X and 13, these switches are protected from corrosion, washdowns, and oil/coolant spraying.

These switches are housed in a durable steel enclosure.

Choose an actuator and contact block to make your own 22 mm plastic switch.

Control multiple devices with one switch. Turn the shaft to change switch positions.

Sized for 22 mm dia. panel cutouts, these switches require a key to turn circuits on or off, limiting access to sensitive equipment.

Vary electrical flow to control speed, volume, and light intensity. Also known as variable output switches or rheostats.

Each selector pack includes one 2” square of FEP, polypropylene, PPS, PVC, CPVC, PVDF, and Teflon® PTFE.

One 2” square of PEEK, PFA, polyimide, Torlon PAI, and Ultem PEI is included in these selector packs.

Compare the appearance choices of our 304 stainless steel with these convenient selector packs.

Includes one 4" × 4" × 0.032" thick piece of 110 copper in the following finishes: plain, brushed, and mirror-like.

Each pack includes one 2" circle of GPO3 fiberglass and Garolite XX, XXX, CE, LE, G-3, G-7, G-9, G-10, and G-11.

Seven wool felt pieces come on a sample sheet that includes information about each felt grade.

Packs contain nine pieces of tubing, each labeled with its hardness.

For monitoring the number of shaft turns on instrumentation, these knobs have easy-to-read scales or digits for quick and accurate readings. Use them on devices with round shafts.

To prevent accidental start-up, these valves can be locked in their off position with a padlock. They create one action, such as extending a cylinder.

The push buttons that operate these valves are separate from the logic unit, allowing you to position them away from machinery. Since both hands are required to simultaneously press the buttons, they protect workers from accidental machinery start-up. They create one action, such as extending a cylinder.

Control six different outputs from a single source of airflow. These valves have one inlet port and six outlet ports. Push in and rotate the dial to move between outlet ports and send airflow to a different output.

Control these valves with one hand. Also known as 4/2 valves, they create two actions, such as extending and then retracting a double-acting cylinder.

These valves close all ports in the off position to stop equipment in a locked position with air pressure holding it in place. They create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as 4-way and 5/3 closed center valves.

In the off position, these valves exhaust all air pressure, allowing the equipment to return to the neutral position. Also known as 4/3 exhaust-center valves, they create two actions, such as extracting and then retracting a double-acting cylinder.

Often used to extend and then retract a cylinder at different speeds, these valves create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as 4-way and 5/2 valves.

Ceramic plates form a longer-lasting seal against oil and dust than rubber seals that deteriorate over time. These valves withstand use in corrosive, dusty, and dirty environments such as foundries, paper mills, and steel plants. Apply voltage to the electrical connection to actuate.

Create two actions at the same time, such as extending two single-acting cylinders at once. Apply voltage to the electrical connection to actuate. Also known as pressure center valves.

In the off position, these valves stop equipment in a locked position with air pressure holding it in place. Often used to extend and then retract a cylinder at different speeds, they create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. They actuate by air signal, so they're good for environments where electrical use may be dangerous.

A simple automation solution that requires no programming, these valves are activated when an object, such as a box rolling on a conveyor, pushes the actuator. They create one action, such as extending a cylinder. Also known as 3-way and 3/2 valves.

Often used to extend and then retract a cylinder at different speeds, these valves create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Use your foot to operate them, leaving your hands free to perform other tasks. Also known as 4-way and 5/2 valves.

Run through equipment cycles up to 30% faster than with standard valves. These valves shift between flow positions in 1.7 ms. Also known as 3/2 valves, they create one action, such as extending a cylinder. Apply voltage to the electrical connection to actuate.

These valves close all ports in the off position to stop equipment in a locked position with air pressure holding it in place. Often used to extend and then retract a cylinder at different speeds, they create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Apply voltage to the electrical connection to actuate.

Rated IP69K, these valves withstand high-pressure, high-temperature washdowns. Their smooth design keeps out dust, dirt, and contaminants, making them easier to keep clean. Apply voltage to the electrical connection to actuate.

Often used to extend and then retract a cylinder at different speeds, they create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as pilot valves and 4-way valves, they use an air signal to actuate, so they're good for environments where electrical use may be dangerous.

Use these valves in areas where ignitable gas and dust may be present. They actuate when voltage is applied to the electrical connection.

Also known as 3/3 valves, these valves close all ports in the off position to stop equipment in a locked position with air pressure holding it in place. They're often used for vacuum suction and release applications and intermediate cylinder stops.

Mount valves to a single-station base or to a manifold, which allows a single pressure source for multiple valves, then add or remove valves as your needs change.