Extend the service life of air-powered tools and equipment by removing particles and water droplets from compressed air.

Extend the service life of air-powered tools and equipment by removing particles and water droplets from compressed air.

Extend the service life of air-powered tools and equipment by removing particles and water droplets from compressed air.

Extend the service life of air-powered tools and equipment by removing particles and water droplets from compressed air.

Use these filters where high water and dirt removal is needed—they have a two-layer filter element made of stainless steel wire mesh and cotton/polyester packing.

Assembled, inspected, and packaged in a clean environment, these filters come sealed in anti-static double bags.

The housing and bowl are 316 stainless steel to handle extremely corrosive environments such as those in semiconductor, marine, chemical, and paper industries.

Protect small air-powered tools, such as impact wrenches, ratchet wrenches, grinders, and screwdrivers.

Also known as coalescing filters, these filters remove compressor oil to extend the service life of air-powered tools and equipment.

Also known as coalescing filters, these filters remove compressor oil to extend the service life of air-powered tools and equipment.

Also known as coalescing filters, these filters remove compressor oil to extend the service life of air-powered tools and equipment.

Also known as coalescing filters, these filters remove compressor oil to extend the service life of air-powered tools and equipment.

Designed for use in main lines with high contamination, these filters remove oil to extend the service life of air-powered tools and equipment.

Mount these filters to a 35 mm DIN rail with the included brackets.

Use these filters to extend the service life of air-powered tools and equipment and then throw them away when you're done.

Use these filters in applications where high-quality air is critical. They remove particles down to 0.003 microns, eliminating small traces of oil vapor and its associated odor.

Two-stage filtration is like getting two filters in one—the first stage removes large particles, while the second removes fine particles.

Generate clean air for instrumentation and applications with critical air requirements.

Remove bacteria, viruses, moisture, and other particles from compressed air and gases used in food, pharmaceutical, biotech, and electronics applications.

A float-operated drain valve on these separators automatically opens when the bowl begins to fill. The first step in water removal, use one of these separators to remove the large amount of water as compressed air cools.

In addition to removing large amounts of water, these separators also remove particles and oil droplets. Place them after your compressor and aftercooler, or at the point of use in applications that don't require an aftercooler.

These filter/regulator combinations come as one convenient unit that cleans the air as it regulates pressure.

A filter and regulator joined top-to-bottom, these filter/regulators fit in the same space as a filter alone.

A filter and regulator joined top-to-bottom, these filter/regulators fit in the same space as a filter alone.

A filter and regulator joined top-to-bottom, these filter/regulators fit in the same space as a filter alone.

With ±0.2 psi accuracy, these filter/regulators provide more precise control than our other compressed air filter/regulators.

Assembled, inspected, and packaged in a clean environment, these filter/regulators come sealed in antistatic double bags.

No need for thread adapters—these filter/regulators have an NPT inlet and a BSPP outlet.

Use these dryer/filters to protect air-powered tools from water, oil, oil vapor, and particles, then throw them away when you're done.

Each of these filter/dryers has two desiccant towers—one that absorbs moisture, particles, and oil in the air while the other reactivates saturated desiccant so you have an uninterrupted supply of clean, dry compressed air.

Install these dryers just before air-powered tools as final protection from water and particles and throw them away when you’re done.

Separate bearings, collars, hubs, and other shaft-mounted items so you can remove them.

Clamp these separators into the V-groove of a pulley for a secure grip.

Grip bearings, gears, and wheels from the outside edge to pull them off a shaft.

Sets include various sizes of quick-hold external grip pullers. Each puller has a cage around the jaws that keeps them in place for a quick job of gripping bearings and pulleys.

These low-capacity pullers are often used to remove corroded battery terminals.

With a variety of expanding collets that secure bearings and bushings from inside, these puller sets let you get a grip on objects with blind holes.

Also known as pilot bearing pullers, use these pullers to grip the interior edge of press-fit bearings, oil seals, and bushings.

Install and remove bearings, pulleys, sprockets, and other press-fit parts with tapered holes.

Complete with a locking storage box, use the pullers in this set to tackle a wide variety of pulling jobs—use pullers to grip objects from the outside or the inside.

Self-locking jaws hold these pullers in place for quick one-hand operation. Spring tension holds the jaws against the object being pulled, so you can tighten the locking nut.

Like the claw end of a hammer around a nail, these wedges grip studs or rods from both sides to give you leverage for prying apart two joined components.

These tools are often used for lifting and aligning machinery or to separate pipe flanges. They’re also known as banana wedges.

These wedges won't damage materials such as wood and plastic.

Make quick height adjustments. Also known as fox and flange wedges.

Insert into a tight space and then squeeze the pump to inflate and pry objects apart.

For a comfortable grip, these pry bars have a plastic handle.

Lift and pry small objects, such as electronic and circuit board-mounted components. These tools are also known as chip lifters.

Slide these bars under heavy objects for prying, lifting, and positioning jobs.

With 14 different head positions, these pry bars fit into difficult-to-access spots for maximum leverage.

The claw-shaped end grips and extracts nails, tacks, and brads. Also known as claw bars.

Made of aluminum-bronze that is Factory Mutual approved, these tools inhibit sparking and are nonmagnetic and corrosion resistant. They satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Insert the support rod into a flange bolt hole and turn the hex bolt to drive the spreader.

Attach this tool to your drill to remove all styles of domed head rivets.

Keep a selection of extractors on hand to back out a variety of broken parts without damaging the threads around them.

Drill a hole in the broken part, insert the extractor, and turn. The part will back out without damaging the threads around it.

The extractors in this set are matched with the right drill bit sizes as well as bushings to help you drill a centered hole into the broken part.

These extractors provide the tightest fit and the most contact with the part to be removed but also cause the most expansion.

Deep flutes provide a strong grip and reduced expansion of the part you need to extract.

These sets have a variety of extractors to drill and remove broken screws, bolts, and studs with a single tool.

The tapered wedge shape of these extractors won’t expand the broken part, making it easier to remove. Sets include the matching drill bit sizes.

With a short and stocky design, the extractors in these sets provide a strong grip without needing to drill a deep hole. After drilling, insert the extractor and turn.

Insert the extractors in these sets into a pipe or fitting and turn with a wrench—the knurls will grip the part so you can twist it out.

Remove button-head socket cap screws that have damaged or rounded recesses without drilling.

Extract socket head cap screws that have damaged or rounded recesses without drilling.

These sets have a variety of extractors to remove button-head socket cap screws that have damaged or rounded recesses without drilling.

Use these sets to extract flat-head socket cap screws that have damaged or rounded recesses without drilling.

Use a square-drive ratchet wrench and socket to turn and extract fasteners.

Sets include a selection of extractors you place over stripped or deformed bolt heads that can be difficult to grip with a wrench. Tap in place with a hammer and turn to extract without damaging the threads around the fastener.